Certificate of Compliance Certificate: 1001924 (079626_0_000) Issued to: ABB Inc. 17100 Manchac Park Lane Suite B Baton Rouge, Louisiana 70817 USA Attention: Fred Ramirez The products listed below are eligible to bear the CSA Mark shown Issued by: Madhumathi Kulothungan Madhumathi Kulothungan PRODUCTS CLASS - C225802 - PROCESS CONTROL EQUIPMENT-For Hazardous Locations- CLASS - C225804 - PROCESS CONTROL EQUIPMENT-Intrinsically Safe, Entity - For Hazardous Locations- CLASS 2258 02 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations XP: Class I, Division 1, Groups A, B, C and D; Class II, Groups E, F and G; Class III: Level Transmitter AT100, AT100S and AT200 Series with 3/4" NPT probe entry with rigid probe. Input rated: 36Vdc, 4-20mA; Enclosure: Type 4X; Maximum ambient: 66 C; Maximum Working Pressure (MWP): 3000 psi Single Seal. XP: Class I, Division 1, Groups B, C and D; Class II, Groups E, F and G; Class III: Level Transmitter AT100, AT100S and AT200 Series with 1-1/8" UNEF probe entry with rigid probe. Input rated: 36Vdc, 4-20mA; Enclosure: Type 4X; Maximum ambient: 66 C; Maximum Working Pressure (MWP): 3000 psi, Single Seal. CLASS 2258 04 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe Entity - For Hazardous Locations IS: Class I, Division 1, Groups A, B, C and D; Class II, Groups E, F and G; Class III; NI: Class I, Division 2, Groups A, B, C and D: DQD 507 Rev. 2016-02-18 Page 1
Intrinsically Safe Level Transmitter AT100, AT100S and AT200 Series. Enclosure Type 4X Maximum ambient: 66 C; Temperature Code: T4; Maximum Working Pressure (MWP): 3000 psi, Single Seal, Fieldbus: Entity Parameters for module options with F suffix: Vmax = 28V; Imax = 250mA; Pmax = 1.2W; Ci = 0.005µF; Li = 10µH when installed in accordance with the installation drawing ELE1036. All other Options: Entity Parameters: Vmax = 36V; Imax = 200mA; Pmax = 1W; Ci = 0.005µF; Li = 10µH when installed in accordance with the installation drawing ELE0001. Model Nomenclature for XP, NI and IS Equipment: Model AT100.a.b.c.d.e.f.g.h.i.j.k.l.m.n.o.p.q.r.s.t.u where: a = Probe Material: S6, A2, H1 or TF. b = Transmitter Configuration L, LW, T, TW, C, CW or Z9. d = Probe Configuration: R1, HP, SW1 or SW2. (For XP and NI rated products.) d = Probe Configuration: R1, F1, HP, SW1, SW2 or SW3 (For IS rated products.) e = Process Temperature Options: H0, H1, H2 or H3. f = Electronic Module: M4A, M4B, M4AS, M4BS, M5A, M5B, M5AS, M5BS, M4AF, M4BF, M5AF or M5BF. g = Second 4-20mA Analog Output: Y or AR (For XP rated products.) g = Second 4-20mA Analog Output: Y (For IS rated products.) h = Agency Approvals: N2 or N3. (For XP and NI rated products.) h = Agency Approvals: N1 or N3. (For IS rated products.) i = Process Connection Type (Any connection type, not part of CSA evaluation.) j = Process Connection Material (Any connection material, not part of CSA evaluation.) k = Flange or Plug Size / Rating / Type (Any flange/plug, not part of CSA evaluation.) l = Float Type (Any float type, not part of CSA evaluation.) m = Second Float Type (Any second float type, not part of CSA evaluation.) n = Probe End Connection Type (Any probe end connection, not part of CSA evaluation.) o = Additional Approvals or Certifications (Any additional approvals, not part of CSA evaluation.) p = Sensor Options (Any sensor options, not part of CSA evaluation.) q = Device Identification Plate: (Any identification plate, not part of CSA evaluation). r = Electrical Connector Type: U8 or U9. s = Not used t = Special Other: TEZ, STH or STF. u = Mounted Accessories: A3. Model AT100S.a.b.c.d.e.f.g.h.i.j.k.l.m.n.o.p.q.r.s.t.u where: a = Probe Material: S6, A2 or H1 b = Transmitter Configuration: L, LW, T, TW, C, CW or Z9. d = Probe Configuration: S1, S2, S3, S4 or SW1. (For XP and NI rated products.) d = Probe Configuration: S1, S2, S3, S4 SW1 or SW3. (For IS rated products.) e = Probe Finish: Y0, 1F, 2F, EP or Z9. DQD 507 Rev. 2016-02-18 Page 2
f = Process Temperature Options: H0, H1 or H2. g = Electronic Module: M4A, M4B, M4AS, M4BS, M5A, M5B, M5AS, M5BS, M4AF, M4BF, M5AF or M5BF. h = Second 4-20mA Analog Output: Y or AR (For XP rated products.) h = Second 4-20mA Analog Output: Y (For IS rated products.) i = Agency Approvals: N2 or N3. (For XP and NI rated products.) i = Agency Approvals: N1 or N3. (For IS rated products.) j = Process Connection Type (Any connection type, not part of CSA evaluation.) k = Process Connection Material (Any connection material, not part of CSA evaluation.) l = Flange or Plug Size / Rating / Type (Any flange/plug, not part of CSA evaluation.) m = Float Type (Any float type, not part of CSA evaluation.) n = Second Float Type (Any second float type, not part of CSA evaluation.) o = Additional Approvals or Certifications (Any additional approvals, not part of CSA evaluation.) p = Sensor Options (Any sensor options, not part of CSA evaluation.) q = Device Identification Plate: (Any identification plate, not part of CSA evaluation.) r = Electrical Connector Type: U8 or U9. s = not used. t = Special Other: TEZ, STH or STF. u = Mounted Accessories: A3. Model AT200.a.b.c.d.e.f.g.h.i.j.k.l.m.n where: a = Mounting: BL, BLW, BR, BRW, TL, TLW, TR or TRW b = Transmitter Configuration L, L9, C, L9C or Z9. d = Probe Type: R1, H2 or IW. e = Electronic Module: M4A, M4B, M4AS, M4BS, M4AF or M4BF f = Second 4-20mA Analog Output: Y or AR (For XP rated products.) f = Second 4-20mA Analog Output: Y (For IS rated products.) g = Agency Approvals: N2 or N3. (For XP and NI products.) g = Agency Approvals: N1 or N3. (For IS products.) h = Additional Approvals or Certifications (Any additional approvals, not part of CSA evaluation.) i = Sensor Options (Any sensor options, not part of CSA evaluation.) j = Device Identification Plate: (Any identification plate, not part of CSA evaluation.) k = Electrical Connector Type: U8 or U9. l = not used. m = Special Other: TEZ, STH or STF. n = Mounted Accessories: A3, AP or AV. Notes related to CSA C22.2 No: 61010-1(Edition 3): 1. The models AT100/100S/200 are permanently connected, Equipment Class I, Over voltage category I 2. Mode of operation: Continuous 3. Pollution degree: 4 4. Environmental conditions: Temperature -40 C to +66 C, Altitude 2000m, 0-100% Relative Humidity, non-condensing DQD 507 Rev. 2016-02-18 Page 3
APPLICABLE REQUIREMENTS CSA Standard C22.2 No. 0-10 - General Requirements - Canadian Electrical Code Part II CSA Standard C22.2 No. 25-M1966 - Enclosures for Use in Class II Groups E, F and G Hazardous Locations CSA Standard C22.2 No. 30-M1986 - Explosion-Proof Enclosures for Use in Class I Hazardous Locations CSA Standard C22.2 No: 61010-1-12 - Safety requirements for electrical equipment for measurement, control (IEC 61010-1: 2010 MOD) and laboratory use CSA Standard C22.2 No. 157-M1992 - Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations CSA Standard C22.2 No. 213-M1987 - Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations ANSI/ISA-12.27.01-2003 - Requirements for Process Sealing Between Electrical Systems and Flammable or Combustible Process Fluids DQD 507 Rev. 2016-02-18 Page 4
Supplement to Certificate of Compliance Certificate: 1001924 (079626_0_000) The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Project Date Description Product Certification History 70040202 2017-02-15 Update Report 1001924 to include update of standard CSA C22.2No: 142 to CSA C22.2 No: 61010-1 (Edition 3); addition of 1, removal of 1 and revision of 8 drawings. 70043466 2015-10-15 Update report 1001924 to include an extensive nomenclature revision, several drawing updates to reconcile with other CB agencies, drawing deletions because they are obsolete or they are not deemed safety critical or they have their contents covered in another drawings and to base the NI ratings on the IS method of protection so that a further reduction in descriptive drawings would be acceptable. 70012693 2015-05-14 Update to Report 1001924 to change the method used to secure and seal the glass window for the HSG2002 enclosure assembly, based on updated CSA Report 1361004 (project 1 of 2); assumes no additional testing is required and national deviations are supplied for Canada. 2391973 2011-02-15 Update of Report 1001924 to include minor drawing revisions and to include an update to Sensor Holder Drawing MC3001 2313359 2010-08-19 Update of Report 1001924 to include listing (nomenclature) from the Report to the Certificate and revised drawings. 1995855 2008-10-02 Update to report 1001924 to include Intrinsically Safe certification for Groups A and B 1978878 2008-09-11 Update report 1001924 to include single seal evaluation to ANSI/ISA 12.27.01. Based on the provision of calculations to waive testing for fatigue and temperature cycling. 1866010 2007-02-20 Update to report 1001924 to include new LCD board (IS and Explosion-proof) based on MT2000 update with same scope. DQD 507 Rev. 2016-02-18 Page 1