Linear Shower Bases 6030 Linear RH Drain (LBUxx603025R) 6030 Linear LH Drain (LBUxx603025L)

DO NOT RETURN PRODUCT OR CONTACT STORE! FOR QUESTIONS OR CONCERNS please call or e-mail our customer support team 8:00am-4:30pm EST. Monday - Friday 1-800-458-9036 lyonssupport@lyonsindustries.com 6032 Linear RH Drain (LBUxx603225R) 6032 Linear LH Drain (LBUxx603225L) Linear Shower Bases 6030 Linear RH Drain (LBUxx603025R) 6030 Linear LH Drain (LBUxx603025L) 317/8" 597/8" 297/8" 597/8" 20 20 20 20 20 20 33½" 159 1 8½" 6032 Stud Layout Base with LH drain shown opposite for RH drain 159 1 149/1 31½" 8½" 6030 Stud Layout Base with LH drain shown opposite for RH drain 60" 4834 Linear CTR Drain (LBUxx483425) 3636 Linear CTR Drain (LBUxx363625) 60" 337/8" 477/8" 357/8" 357/8" 14" 20" 14" 8" 20" 8" 35½" 169 1 24" 4834 Stud Layout 37½" 179 1 18" 3636 Stud Layout 48" 3 3232 Linear CTR Drain (LBUxx323225) 317/8" 317/8" 33½" 159 1 20" 1 32" 3232 Stud Layout *Stud spacing critical for shelf placement when installing Linear Shower Wall Subject to manufacturing tolerance of [+] or [-] 1/8" Page 1

TOOLS YOU WILL NEED: Level Jig saw Tape measure Pencil Power Drill Safety Glasses SUPPLIES YOU WILL NEED: Screws, 2" Flathead Shims Construction Adhesive Mortar compound (optional) Drain assembly Silicone caulk Sioux Chief drain body: (Model#825-L20P / Menards SKU#6895847) Sioux Chief square strainer: (Chrome Model#821-2SCQPK2 / Menards SKU#6895841) (Bronze Model#821-2SRBQPK2 / Menards SKU#6895843) (Nickel Model#821-2SKQPK2 / Menards SKU#6895845) IMPORTANT Allow base to reach room temperature before installation. Before you begin determine appropriate product reference (Page 1). Read installation instructions carefully before starting project. Do not use plumber's putty. May result in product failure. Use a high grade silicone caulk for all necessary locations. Keep instructions for warranty information. Before installation, peel away protective film to ensure correct color. INSTALLATION INSTRUCTIONS STEP 1. PREPARING ALCOVE a. Strip alcove to bare studs. b. Shower stud pocket should be constructed as shown on page 1. Studs should be plumb and square to sub-floor. c. Sub floor must be clean, smooth, and level (check with level). Do not install shower base on open floor joists. d. Cut hole in sub floor as shown on page 1 to accommodate drain (not included). STEP 2. TRIAL FIT BASE a. Trial fit base in prepared alcove. With base sitting flat on floor ensure base is level (Fig 1). NOTE: If sub-floor is not level, use shims or a leveling compound (smooth mortar) or a similar quick-setting compound specifically made for leveling floors. This fully supports and levels base. b. Remove base from alcove. STEP 3. INSTALLING BASE a. Follow Sioux Chief's instructions for installing square drain. b. Apply construction adhesive to all feet (and shims if needed) (Fig 2 & 3). c. Carefully set shower base in alcove. Avoid sliding base, which will smear adhesive. d. If needed, shim between nail flange and stud(s) to create a tight fit. e. Once leveled, screw nail flange to all studs (Fig 4). IMPORTANT - PLEASE READ Failure to adhere feet to subfloor and screw flange to all studs will void warranty 5/8" waterproof board is required when installing tile FIGURE 1. Check to assure base is level. FIGURE 2. Apply construction adhesive to all feet. Adhesive and Shims FIGURE 3. If needed, place shims under feet into adhesive to level base. Page 2 FIGURE 4. If needed, shim between nail flange and stud(s) for tight fit. Screw flange to all studs.

CLEANING +Do not use any abrasive cleaners or metal scrapers. +If drywall mud or plaster gets on your shower, it may be carefully removed with a wooden scraper made from a piece of scrap wood. +Adhesive may be removed with mineral spirits. +Ideal cleaners are Soft Scrub Gel or Comet Gel. WARNING: Some cleaning products are not suitable for use. Read all labels carefully. DO NOT USE if they say not suitable for use with ABS, acrylic, or polystyrene." SCRATCH REMOVAL INSTRUCTIONS 1. For effective scratch removal and polishing, you will need to purchase these items. 1 sheet 1000 grit 3M wet-dry sandpaper 1 sheet 1500 grit 3M wet-dry sandpaper 1 sheet 2000 grit 3M wet-dry sandpaper 1 small container of 3M rubbing compound These items can be purchased at most auto supply stores that provide supplies to professional paint and body shops. Call before you go. Not all auto supply stores will have these items. 2. Start sanding with 2000 grit paper. Use small squares of paper about 2" x 2" for all sanding and use lots of water. The water serves as both a lubricant and to prevent residue buildup on the paper. Residue buildup shortens the effective life of the paper and may scratch the surface you re trying to polish. 3. 2000 grit paper is the finest grit available (the higher the number, the finer the grit). If you can t remove all of the scratches with 2000 grit, switch to 1500 grit. Remember to wash the paper frequently with water as you sand. 4. If all of the scratches can t be removed with 1500 grit, switch to 1000 grit. This should remove most fine scratches. If you have deep scratches or a gouge, coarser paper may have to be used (see chart to right). Be careful! Using grit that is too coarse may actually put in more scratches than it removes. 5. Once you have removed all of the scratches, by sanding with the finest paper possible, repeat the sanding process using successively finer grits of paper until you ve once again sanded with 2000 grit. 6. Now use 3M rubbing compound on a soft, damp cloth. Polish using considerable pressure to produce a smooth, shiny finish. SUPERFICIAL SCRATCH 2000 grit LIGHT SCRATCH 1500 2000 grit MEDIUM SCRATCH 1000 2000 grit DEEP GOUGE 600 2000 grit SCRATCH / SANDPAPER GUIDE Page 3 Lyons Industries, Inc. 30000 M-62 West, Dowagiac, MI 49047 phone (800) 458-9036 fax (269) 782-5159 lyonsindustries.com e-mail lyonsind@lyonsindustries.com 09-08-2016

LYONS SHOWER FIXTURE LIMITED WARRANTY 5-YEAR CONSUMER, 2-YEAR COMMERCIAL Lyons Industries, Inc. warrants to the original purchaser that this Lyons fixture will be free of manufacturing defects, which affect its performace as a bathing or showering fixture, under the following conditions and subject to the limitations contained in the Remedies and Warranty Limitations sections. The Limited Warranty applies for 5 years from the date of purchase if the fixture is used in a residential owner-occupied building for non-commercial purposes; or for 2 years from the date of purchase if it is used in any other building, including any building used for rental, commercial, or business purposes. This Limited Warranty is void if the fixture is not installed in accordance with the installation instructions supplied by Lyons, or local building codes and ordinances, or if the care and cleaning instructions supplied by Lyons are not followed. This Limited Warranty is also void if the fixture is moved from the location of its initial installation, or is subjected to accident, abuse, or misuse. The Limited Warranty excludes normal wear and tear, and does not cover damage that can be repaired by following the Scratch Removal Instructions. This Limited Warranty shall be void unless any failure or non-conformance is discovered before the expiration of this warranty, and is reported to Lyons, in writing, accompanied by the original proof of purchase, within 30 days of discovery, to: Lyons Industries, Inc., 30000 M-62 West, Dowagiac, Michigan 49407 REMEDIES The original purchaser s remedy under this Limited Warranty is limited to the repair, replacement, or refund of the purchase price of the fixture, at Lyons sole option, of any part of the fixture which has failed or does not conform to the manufacturer's specifications. In no event shall Lyons be liable for lost profits, loss of use, incidental, special or consequential damages including, but not limited to, damage to or loss of use of the building or its contents, arising out of any defect in the fixture; nor shall Lyons be liable for any amount in excess of the original purchase price of the fixture. Lyons reserves the right to require the return, at purchaser s expense, of the damaged fixture for repair or exchange before providing services under this Limited Warranty. If Lyons elects to replace the fixture, its obligation is limited to supplying a replacement unit or component part of comparable size and style, and does not include the cost of removal, installation, or transportation, which must be borne by the purchaser. Replacement parts provided under this Limited Warranty are warranted for the remainder of the original warranty period applicable to the fixture, as if such parts were orginal components of that fixture. WARRANTY LIMITATIONS THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IM- PLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. LYONS DISCLAIMS ANY AND ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUEN- TIAL DAMAGES. Some states do not allow limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you. In such states, Lyons liability shall be limited to the extent permitted by state law. ANY IMPLIED WARRANTIES ARISING BY WAY OF STATE LAW, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION AND IN SCOPE OF COVERAGE TO THE TERMS OF THIS LIMITED WARRANTY, UNLESS A SHORTER PERIOD IS ALLOWED BY LAW. Page 4

597/8" 57" Door 317/8" Nail DO NOT RETURN PRODUCT OR CONTACT STORE! FOR QUESTIONS OR CONCERNS please call or e-mail our customer support team 8:00am-4:30pm EST. Monday - Friday 1-800-458-9036 lyonssupport@lyonsindustries.com 331/2" Linear Shower Walls LSUxx603274 Fits most standard 60" x 32" 6032 Stud Layout 20" 20" 20" 597/8" 57" Door 297/8" Nail 311/2" LSUxx603074 Fits most standard 60" x 30" 6030 Stud Layout 20" 20" 20" 60" 60" 477/8" 337/8" 45" Door Nail 351/2" LSUxx483474 Fits most standard 48" x 34" 4834 Stud Layout 14" 20" 14" 357/8" 33" Door 357/8" Nail LSUxx363674 Fits most standard 3 x 3 371/2" 3636 Stud Layout 8" 20" 8" 48" 3 317/8" 29" Door 317/8" Nail 331/2" LSUxx323274 Fits most standard 32" x 32" 3232 Stud Layout 20" 32" Before installation, peel away protective film to ensure correct color *Stud spacing critical for shelf placement Page 1

TOOLS YOU WILL NEED Tape Measure Level Drill Pencil Safety Glasses Appropriate Hole or Saber Saw (for Faucet Installation) Caulk Gun 3 Tubes of Adhesive Compatible with Polystyrene Caulk (for Faucet Installation) Screws (Flathead Stainless) 2" Masking Tape Shims INSTALLATION INSTRUCTIONS IMPORTANT Allow panels to reach room temperature before installation. Before you begin determine appropriate product reference (Page 1). Seal strips (included) are required for proper installation. Read installation instructions carefully before starting project. When installing Lyons walls on a shower base from another manufacturer caulk is required. Do not use plumber s putty. Will cause product failure and void warranty. Use a high grade silicone caulk for all necessary locations. Keep instructions for warranty information. FIGURE 1. Check that studs are plumb with sub-floor/base. STEP 1. PREPARING ALCOVE a. Strip alcove to bare studs. b. Stud pocket should be constructed as shown on page 1. Studs must be plumb and square to sub-floor. Sub floor must be level. (Fig. 1) c. Check that there are no screws, nails or staples in the studs that will interfere with installation. d. If installing over existing shower base check that studs are plumb to the shower base and shower base is level. Go to step 3. e. If desired add appropriate rated insulation between studs. FIGURE 2. Carefully separate seal strip. DO NOT CUT! Top Nail Seal Strip Front of Back Panel STEP 2. SHOWER BASE INSTALLATION a. Follow manufacturer s instructions for installing your shower base. IMPORTANT Shower base must be plumb and square to alcove for proper wall installation FIGURE 3. Place seal strip on both sides of back panel. STEP 3. INSTALL SEAL STRIP a. Carefully separate (NOTE: PULL APART - DO NOT CUT) seal strip. (Fig. 2) b. Peel back protective film along all edges of back panel. c. Place seal strip along both sides of back panel removing protective paper as you apply. (Fig. 3) IMPORTANT - DO NOT STRETCH SEAL STRIP! d. Apply pressure along the entire length of each seal strip to activate adhesive. Trim any excess. NOTE: Failure to install seal strip will cause water damage and void warranty If seal strip is missing, please contact customer support before installing FIGURE 4. All panels must fully contact required studs. Seal Strip Front of Back Panel STEP 4. TRIAL FIT PANELS a. All panels must fully contact required studs as shown on page 1. (Fig. 4) b. Place back panel then fit side panels into place. (Fig. 5) c. Center wall on shower base. Make sure panels rest flat on shower base. d. If necessary, shim between panels and studs to provide a tight fit between the back and side panels. (Fig. 6) e. Align the front of the side walls to the front of the shower base. This makes drywall installation easier. f. Mark height of wall on each stud to indicate where to apply adhesive on the stud. (Fig. 7) g. Measure and mark all control holes. After removing side panels, drill or saw necessary holes. IMPORTANT Drill or saw holes from front side. Cover area to be cut with masking tape to prevent chipping and scratching Front of Side Panel Front of Back Panel FIGURE 5. Fit side panels into place on back wall panel. If necessary shim panels at each stud to assure proper fit. Page 2 FIGURE 6. You can shim against the stud.

INSTALLATION INSTRUCTIONS (continued) STEP 5. INSTALLING SHOWER WALL IN ALCOVE a. Peel back protective film along bottom edge of back and side panels. b. Apply a generous bead of adhesive below mark on each back panel stud only (follow adhesive manufacturer s recommended instructions). c. Place back panel and center on base. d. Apply adhesive to studs for side panel opposite the shower controls and place side panel. e. Apply adhesive to studs for faucet side panel and place side panel. (Fig. 8) f. Center wall panels on shower base. Make sure panels are resting flat on base. g. Reposition shims if needed. h. Press back panel firmly into place and align the front of the side walls to the front of the shower base and screw back panel nail flange to studs. i. Apply pressure to one side panel, directing the pressure towards back panel, then screw vertical nail flange to stud. Repeat for opposite side panel. j. Screw top flange of side panels to studs. k. Panels must be held tight to studs during drying process. Apply pressure to panels while adhesive dries with cross bracing. (Fig. 9) FIGURE 7. Mark studs. MARK TOP OF STUD CENTER ASSEMBLED WALL ON BATHTUB/SEATED BASE IMPORTANT - Failure to adhere panels and screw all flanges to all studs will void warranty STEP 6. CAULKING a. When installed on any Lyons shower base your Linear wall is designed to function properly without seams being caulked. b. If you prefer the appearance of caulked seams, caulk all seams or leaks may occur. c. Caulk must be applied around holes for the faucet, diverter valve and shower head. d. If your Linear wall is used on a shower base other than a Lyons, it is required to caulk all seams. e. If a shower door is installed, caulk is required between the shower base, wall, and door. f. For best results always use a high-grade silicone caulk. FIGURE 8. Apply adhesive. STEP 7. FINISHING Green Board or Other Finishing Boards a. Shim studs with lattice strips or 1/4" luan so that finishing board will overlap nail flanges. (Fig. 10) Tile a. Install finishing board up to (not over) nail flanges. b. Install tile over finishing board and nail flanges. CLEANING Do not use any abrasive cleaners or metal scrapers. If drywall mud or plaster gets on a finished surface it may be carefully removed with a wooden scraper made from a piece of scrap wood. Adhesive may be removed with mineral spirits. Ideal cleaners are Soft Scrub Gel, Comet Gel or 409. FIGURE 9. Apply pressure by cross bracing left and right panels while also applying pressure to the back panel. WARNING: Some cleaning products are not suitable for use. Read all labels carefully. DO NOT USE if they say not suitable for use with ABS, acrylic or polystyrene". FIGURE 10. Shim studs. Page 3

LYONS FIXTURE LIMITED WARRANTY 5-YEAR CONSUMER, 2-YEAR COMMERCIAL Lyons Industries, Inc. warrants to the original purchaser that this Lyons fixture will be free of manufacturing defects, which affect its performance as a bathing or showering fixture, under the following conditions and subject to the limitations contained in the Remedies and Warranty Limitations sections. The Limited Warranty applies for 5 years from the date of purchase if the fixture is used in a residential owner-occupied building for non-commercial purposes; or for 2 years from the date of purchase if it is used in any other building, including any building used for rental, commercial or business purposes. This Limited Warranty is void if the fixture is not installed in accordance with the installation instructions supplied by Lyons or local building codes and ordinances or if the care and cleaning instructions supplied by Lyons are not followed. This Limited Warranty is also void if the fixture is moved from the location of its initial installation or is subjected to accident, abuse or misuse. The Limited Warranty excludes normal wear and tear and does not cover damage that can be repaired by following the Scratch Removal Instructions. This Limited Warranty shall be void unless any failure or non-conformance is discovered before the expiration of this warranty and is reported to Lyons, in writing, accompanied by the original proof of purchase, within 30 days of discovery, to: Lyons Industries, Inc., 30000 M-62 West, Dowagiac, Michigan 49407 REMEDIES The original purchaser s remedy under this Limited Warranty is limited to the repair, replacement or refund of the purchase price of the fixture, at Lyons sole option, of any part of the fixture which has failed or does not conform to the manufacturer's specifications. In no event shall Lyons be liable for lost profits, loss of use, incidental, special or consequential damages including, but not limited to, damage to or loss of use of the building or its contents, arising out of any defect in the fixture; nor shall Lyons be liable for any amount in excess of the original purchase price of the fixture. Lyons reserves the right to require the return, at purchaser s expense, of the damaged fixture for repair or exchange before providing services under this Limited Warranty. If Lyons elects to replace the fixture, its obligation is limited to supplying a replacement unit or component part of comparable size and style, and does not include the cost of removal, installation, or transportation, which must be borne by the purchaser. Replacement parts provided under this Limited Warranty are warranted for the remainder of the original warranty period applicable to the fixture, as if such parts were original components of that fixture. WARRANTY LIMITATIONS THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. LYONS DISCLAIMS ANY AND ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you. In such states, Lyons liability shall be limited to the extent permitted by state law. ANY IMPLIED WARRANTIES ARISING BY WAY OF STATE LAW, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION AND IN SCOPE OF COVERAGE TO THE TERMS OF THIS LIMITED WARRANTY, UNLESS A SHORTER PERIOD IS ALLOWED BY LAW. SCRATCH REMOVAL INSTRUCTIONS 1. For effective scratch removal and polishing, you will need to purchase these items. 1 sheet 1000 grit 3M wet-dry sandpaper 1 sheet 1500 grit 3M wet-dry sandpaper 1 sheet 2000 grit 3M wet-dry sandpaper 1 small container of 3M rubbing compound #05933 These items can be purchased at most auto supply stores that provide supplies to professional paint and body shops. Call before you go. Not all auto supply stores will have these items. 2. Start sanding with 2000 grit paper. Use small squares of paper about 2"x 2" for all sanding and use lots of water. The water serves as both a lubricant and to prevent residue buildup on the paper. Residue buildup shortens the effective life of the paper and may scratch the surface you're trying to polish. 3. 2000 grit paper is the finest grit available (the higher the number, the finer the grit). If you can't remove all of the scratches with 2000 grit, switch to 1500 grit. Remember to wash the paper frequently with water as you sand. 4. If all of the scratches can't be removed with 1500 grit, switch to 1000 grit. This should remove most fine scratches. If you have deep scratches or a gouge, coarser paper may have to be used (see chart to right). Be careful! Using grit that is too coarse may actually put in more scratches than it removes. 5. Once you have removed all of the scratches, by sanding with the finest paper possible, repeat the sanding process using successively finer grits of paper until you've once again sanded with 2000 grit. 6. Now use 3M rubbing compound #05933 on a soft, damp cloth. Polish using considerable pressure to produce a smooth, shiny finish. SUPERFICIAL SCRATCH 2000 grit LIGHT SCRATCH 1500 2000 grit MEDIUM SCRATCH 1000 2000 grit DEEP GOUGE 600 2000 grit SCRATCH / SANDPAPER GUIDE Page 4 Lyons Industries, Inc. 30000 M-62 West, Dowagiac, MI 49047 phone (800) 458-9036 fax (269) 782-5159 lyonsindustries.com e-mail lyonsind@lyonsindustries.com 9-8-2016