; 5 w_p_rogr_a_m_m_ab_l_e_s_i_ng_le_o_utp_u_t A_E_-_5 s_e_rie_s - THE POWER SUPPLERTM Features:... Universal AC input Full range '... Programmable output Voltage (% - 5%) ' Programmable output Current (% - 5%) Forced current sharing at parallel operation Constant current limit Selectable +5V.5A or +9V.3A auxiliary output Global control via RS232 Remote setting multiple PSU via RS232, RS485 & 2 C Power OK signal Remote ON OFF, Remote sense function Protection: OVP, OlP, OTP, Fan failure 3 years warranty c'i\lus C E: E2483 MODEL AE 5 2 AE 5 5 AE 5 24 AE 5 3 AE 5 36 AE 5-48 AE 5-6 DC Voltage Range 2V 5V 24V 3V 36V 48V 6V Rated Current 25A A 62,5A 5A 4,7A 3,3A 25A Current Range -25A -looa o -62,5A - SOA - 4,7A - 3,3A o -25A Rated Power 5W 5W 5W 5W 5W 52W 5W Ripple & Noise (Max.) Note.2 5mVp-p lsomvp-p 24mVp-p 3mVp-p 36mVp-p 48mVp-p 6oomVp-p Output Voltage Adj, Range ::5,% Typical adjustment by potentiometer. (VR) Voltage Tolerance Note,3 %2,% Line Regulation ::,% Load Regulation Setup, Rise Time Hold Up Time (Typ.) Voltage Range Frequency Range Power Factor (Typ,) ±l,o% SOOms, looms at full load 4ms 23VAC at full load Note.4 9-264VAC, 27-37VDC 47-63Hz,95 23VAC,,99 5VAC at fulload nput Efficiency (Typ,) 89% 9% 92% 92% 92% 92/. 93% Protection Function AC Current (Typ.) nrush Current (Typ,) Leakage Current Over Load Over Voltage Over Temperature Auxiliary Power Remote ON OFF Control lsa 5VAC, 9A 23VAC 3A 5VAC.45A/23VAC < 2.5mA 24VAC 5% rated output power Protection type: Constant current limit Variable OVP, 2 ± 7% Vout. Refer to VC VS OVP curve. Protection type: Latch-style (Recovery after reset AC power ON or inhibit) 85 ±S'C detect on heat sink of secondary side ProteclionlJlpe: Auto recovery after temperature goes down Selectable +5V.5A or +9V.3A auxiliary output By external swlch Power OK Signal Open drain signal low when PSU turns on, Max. sink current: 2mA, Max. drain voltage: 4V. Output Voltage Trim Output Current Trim Parallel (Current Sharing) Note,5 Please refer to page 5 Working Temp. Working Humidity Adjustment of output voltage s between - 5% of rated output Adjustment of output current is between - 5% of rated output -2 - +6' C (Refer to load de-rating curve) 2-9% RH non-condensing Environment Storage Temp. & Humidity -4 - +S5 C, - 95% RH Safety & EMC Temp. Coefficient ::.2% ' C ( - SO' C) Vibration - 5Hz. 2G min, cycle. period for 6min. each along X. Y. Z axes Compliance to EC 68-2-6. EC 68-2-64 Safety Standards Certified UL 695-: EN 695- Withstand Voltage solation Resistance Note.? /P-O/P: 3KVAC (4242VDC), /P-FG:.5KVAC (22VDC), O/P-FG:.5KVAC (77VDC) P-OP, P-FG, O/P-FG: M Ohms SOOVDC EM Conduction & Radiation Certified EN 5522; EN 624-3; EN 6-6-3 Harmonic Current Certified EN 6-3-2: EN 6-3-3 Note.6 EMS mmunity Certified EN 5524; EN6 24-3; EN6-6-; EC 6-4-2, 3, 4, 5, 6, 8, Cooling Load and temperature control fan Others Dimension (WxHxD) 27x63.5x28 mm 5.x2.5xll.24 inch Note Packing 2.6kg: Spes S.6kg.S6CUFT. All parameters NOT specially mentioned are measured at 23VAC input, rated load and 25 C of ambient temperature. 2. Ripple & noise are measured at 2MHz of bandwidth by using a 2 twisted pair-wire terminated with a O.luF & 47uF parallel capacitor. 3. Tolerance: includes setup time tolerance, line regulation and load regulation. 4. De-rating may apply in low input voltage. Please check the de-rating curve for more details. 5. n parallel connection only one unit will operate if the total output load is less than 5% of the rated power. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. REV. 8< 7. This test is done without enclosure. 45.'2
AKN SEo 9 poo CCOMPOANY - THE POWER SUPPLERTM 5W Programmable Single Output AE-5 series Mechanical Drawings: Unit:mm inch 28. [.2] 25. [9.84] r-- -- - - - - - - -- - - - - - --- -- -- \4-M4NUT! i - --------- - - - - _.. -,,--,-,- - 33. [2.32] 5. [.59] 635 [2 5] == = ' ' Z l = == == =; F==, = i ==, == F== B = = = 5'!!i....: 34. [.34] 237. [9.33],Hlft-----.:lt- -._- - ---- - - - - --- - ---------. \ 8-M4 NUT(Double) is.,; ' -'-.!!l--->--' --- - - - - - - - - - - - - - - - - - - - ---u AC nput Terminal Pin No. Assignment Control pin number assignment (CN2): JST S24B-PHDSS or equivalent Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment Mating Housing / Contact ACL VS+ 9 EN- 7 AUX 2 ACN 2 VO+ GND 8 GND 3 VS- EN+ 9 SCL 3 4 VO- 2 AUX 2 SDA JST PHDR-24VS JST SPHD-2T-PO.5 5 POK 3 AC 2 AUX or equivalent or equivalent 6 GND 4 GND 22 GND 7 PAR 5 VC 23 NC. 8 VSET 6 GND 24 NC. CN2 Function Description: Pin No. Function VS+ 2 VO+ 3 VS- 4 VO- 5 POK 6 GND 7 PAR 8 VSET 9 EN- GND EN+ 2 AUX Description Pin No. Function Description Positive output voltage 3 AC Program Remote sense (+) 4 GND Ground Remote sense (-) 5 VC V Program Negative output voltage 6 GND Ground Power OK 7 AUX +5V /.5A or +9V /.3A Auxiliary power Ground 8 GND Ground Parallel operation current share 9 SCL Serial Clock used in the 'C interface Aux output setting 2 SDA Serial Data used in the 'C interface nhibit ON/OFF (-) 2 AUX +5V /.5A or +9V /.3A Auxiliary power Ground 22 GND Ground nhibit ON/OFF (+) 23 NC. For RS232 Transmission function +5V /.5A or +9V /.3A Auxiliary power 24 NC. For RS232 Receiver function KEPCO, NC.. 3-38 Sanford Avenue Flushing, NY 355 USA. Tel: (78) 46-7. Fax: (78) 767-2 REV. B4 45.2 2
AKN SEo 9 poo CCOMPOANY THE POWER SUPPLERTM LED Status: Solid(Green) Solid(Orange) 5W Programmable Single Output AE-5 series LED LED Signal Status Power OK (local mode) Power OK (Remote mode) Slow Blink(Green) - - - Power Standby Fast Blink(Red) - - - - - - - - - - - Over Voltage Protection ( OVP ) Solid(Red) Over load Protection ( OlP ) Slow Blink(Red) - - - Over Temperature Protection ( OTP ) ntermittent Blink(Red) - - - - - - Fan Failure nterlace Blink(Red) - - - - Power Failure 'local mode: Use ACNC to control output current and voltage. Remote mode: Use RS-232 or 'C command to control output current and voltage. De-rating Curve: Load V.S Temp. Load V.S lip Voltage fl---------------------_\ - OJ o...j.. 8 - - - - - - - - - -:- -. - - -:- - - - - -. - - - - -:- - - - - -:- --. 6,......... -...,.... 4 ---.-----------------------,,,,,,,, 2 - - - -.- ----,------.. -----.-----... ---- co o -',.,. so -----------.------.----.------.-----.. ------,.,., 7 ----.------.------.---.------.------.------ 6 - - - - - - - - - -:- - - - - - - - - - 5 - - - - - - - - -.:. - - - -.:. - - -- 4 - - - - - - - - - -:- - - - - -:- - - --...... -25 o 2 3 4 5 6 7 Ambient Temperature (Oe) 9 264 CMD VS Output Curve: OUT '',, N Z U r + rh > + > / J J lr / :Z + z U w w.. z tii x Z ::J Z <.? <.?.. <.? g /' // ;.W (// U x --' ::J U >.. l Ul.... Z Z <.? <.? Ul Z <.? o..' v. 'ffit ' Extemal Voltage (VDC) VC VS OVP Curve: 2% 96% 2% ovp ---------------------------------- vel.5v.75v 4.5V 4.SV.75V (Output 5%) 4.5V (Output %) N Z U + rh :Z + z U > w w.... tii c c --' x u Ul 'i. x c c ::J Z Z Z Z >.. <.? <.? <.? <.? $-,.Extemal Resistor (K.!) AD --_-'HpWM 22R VC=C. R -5Vdc R=5K KEPCO, NC.. 3-38 Sanford Avenue Flushing, NY 355 USA. Tel: (78) 46-7. Fax: (78) 767-2 REV. B4 4!5l2 3
AKN SEo 9 poo CCOMPOANY - THE POWER SUPPLERTM Remote ON/OFF: (A) Default Setting J 2KO ------- rx EN+ EN- GND - }sw sw OFF Power OFF ON PowerON (A) Using internal 5V auxiliary source 5W Programmable Single Output AE-5 series (8) AU 2KO L-----t...=-:--, Tr -- Clrl L H (8) ON OFF Control by NPN transistor Clrl GND Power OFF Power ON (C) -------!7AUX Avi r-ini;laux ' ; EN- GND - sw OF Power OFF ON PowerON (C) Using external voltage source Power OK Signal: - - - - - - - - - - - - - --.,r---o'l P.OK ' Good Failure -=rl --', DCDC 5V/O.5A ------<[.) AUX 9V/c:J.3A VSET *Place an additional capacitor to have a better performance of auxiliary power operation. *The grounding of AUX power should be connected to GND port f V- is connected as Grounding, make sure to short the GND and V- ports. nternal Circuit --------------- AUX and P.OK Signal GND *,Z 47lF 6V AUX. LOAD. Remote Sense ld l [[[[[[ : :9N 2 Hi 2 CN2 VO+ VS+ VO- VS- GND POK VSET PAR GND EN+ AUX EN+ GND AC GND VC SDA SCL NC NC 24 23 2. Local Sense (Default setting) Load 2n CN2 VO+ VS+ VO- VS- f- GND POK VSET PAR GND EN+ AUX EN+ GND AC GND VC SDA SCL NC NC 24 23 - y REV. 84 <Y2 4 KEPCO, NC.. 3-38 Sanford Avenue Flushing, NY 355 USA. Tel: (78) 46-7. Fax: (78) 767-2
AN SO 9 COMPANY K E P CO. 5W Programmable Single Output - THE POWER SUPPLERTM 3. Current Sharing with Remote Sensing o]m mm,l iim Qn mm QiOm mmm i :_O9 [ l r OOr o ', L _ [ J _ :_O9 m J.'J 2 2 \\ '-- '.. 2 2 J U J VO+ VO+ VS+ VO+ VS+ VO+ VS+ VO- VS- VO- VS- VO- VS- VO- VS- GND POK GND POK GND POK GND POK VSET PAR - VSET PAR - VSET PAR f-- VSET PAR - GND EN- GND EN- GND EN- GND EN- AUX EN+ AUX EN+ AUX EN+ AUX EN+ GND AC GND AC GND AC GND AC GND VC GND VC GND VC GND VC SDA SCl SDA SCl SDA SCl SDA SCl NC NC NC NC NC NC NC NC 24 23 24 23 24 23 24 23 4. Current Sharing with Local Sensing AE-5 series Qi! [ ml i R9 liij.l QiO; ii U i :_ Qr ii i o \ 2 2 2 2 VO+ VS+ VO+ VS+ VO+ VS+ VO+ VS+ VO- VS- VO- VS- VO- VS- VO- VS- GND POK GND POK GND POK GND POK VSET PAR - VSET PAR r-- VSET PAR r-- VSET PAR - GND EN- GND EN- GND EN- GND EN- AUX EN+ AUX EN+ AUX EN+ AUX EN+ GND AC GND AC GND AC GND AC GND VC GND VC GND VC GND VC SDA SCl SDA SCl SDA SCl SDA SCl NC NC NC NC NC NC NC NC 24 23 24 23 24 23 24 23 KEPCO, NC.. 3-38 Sanford Avenue Flushing, NY 355 USA. Tel: (78) 46-7. Fax: (78) 767-2, REV.8J..4/!S(2
AKN SEo 9 poo CCOMPOANY - THE POWER SUPPLERTM nstallation nstruction:. Mounting Directions - Recommended standard mounting methods: 5W Programmable Single Output AE-5 series (a) (b) (c) 4-M4 / L=4mm max. 4-M4 / L=4mm max.. S 4-M4 / L=4mm max. S 2. Mounting Method 2- There are ventilating holes on the front and back side panels, do not obstruct; allow 5mm at least for air flow. 2-2 The Maximum allowable penetration of screw is 4mm. ncomplete threading should not be penetrated. 2-3 Recommended the torque of mounting screw: M4 screw:.27n m (3.kgf cm) More than 5mm More than 5mm Ai r flow <:::::r---...j FAN FAN KEPCO, NC.. 3-38 Sanford Avenue Flushing, NY 355 USA. Tel: (78) 46-7. Fax: (78) 767-2 REV. 84 <52 6