INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE Phone: (800) 421-6144 Fax: (800) 582-7501 crlaurence.com usalum.com crl-arch.com 11M0230
HANDLING, STORAGE, AND PROTECTION OF The following precautions are recommended to protect the material against damage. Following these precautions will help ensure early acceptance of your products and workmanship. A. HANDLE CAREFULLY. All aluminum materials at job site must be stored in a safe place, well removed from possible damage by other trades. Cardboard wrapped or paper interleaved materials must be kept dry. B. CHECK ARRIVING MATERIALS. Check for quantities and keep records of where various materials are stored. C. KEEP MATERIALS AWAY FROM WATER, MUD, AND SPRAY. Prevent cement plaster or other materials from damaging the finish. D. PROTECT THE MATERIALS AFTER ERECTION. Protect erected frame with polyethylene or canvas splatter screen. Cement, plaster, terrazzo, other alkaline solutions, and acid based materials used to clean masonry are harmful to the finish. If any of these materials come in contact with the aluminum, immediately remove with water and mild soap. IMPORTANT: READ THIS MANUAL THOROUGHLY BEFORE BEGINNING INSTALLATION. 2
GENERAL INSTALLATION NOTES Recommended Guidelines For All Installations: 1. REVIEW CONTRACT DOCUMENTS. Check shop drawings, installation instructions, architectural drawings, and shipping lists to become thoroughly familiar with the project. The shop drawings take precedence and include specific details for the project. Note any field verified notes on the shop drawings prior to installing. The installation instructions are of a general nature and cover most conditions. 2. INSTALLATION. All materials are to be installed plumb, level, and true. Install operable windows preglazed only. 3. BENCH MARKS. All work should start from bench marks and/or column lines as established by the architectural drawings and the general contractor with guaranteed accuracy. Working from these datum points and lines determine: a) The plane of the wall in reference to offset lines provided on each floor. b) The finish floor lines in reference to bench marks on the outer building columns. c) Mullion spacing from both ends of masonry opening to prevent dimensional build-up of daylight opening. 4. FIELD WELDING. All field welding must be adequately shielded to avoid any splatter on glass or aluminum. Results will be unsightly and/or structurally unsound. Advise general contractor and other trades accordingly. All field welds of steel anchors must receive touch-up paint (zinc chromate) to avoid rust. 5. SURROUNDING CONDITIONS. Make certain that construction which will receive your materials is in accordance with the contract documents. If not, notify the general contractor in writing and resolve differences before proceeding with work. 6. ISOLATION OF. Aluminum to be placed in direct contact with uncured masonry or incompatible materials should be isolated with a heavy coat of zinc chromate or bituminous paint. 7. SEALANTS. Sealants must be compatible with all materials with which they have contact, including other sealant surfaces. Consult with sealant manufacturer for recommendations relative to joint size, shelf life, compatibility, cleaning, priming, tooling, adhesion, etc. It is the responsibility of the Glazing Contractor to submit a statement from the sealant manufacturer indicating that glass and glazing materials have been tested for compatibility and adhesion with glazing sealants, and interpreting test results relative to material performance, including recommendations for primers and substrate preparation required to obtain adhesion. The chemical compatibility of all glazing materials and framing sealants with each other and with like materials used in glass fabrication must be established. This is required on every project. 8. FASTENING. Within the body of these instructions "fastening" means any method of securing one part to another or to adjacent materials. Only those fasteners used within the system are specified in these instructions. Due to the varying perimeter conditions and performance requirements, perimeter and anchor fasteners are not specified in these instructions. For perimeter and anchor fasteners refer to the shop drawings or consult the fastener supplier. 9. BUILDING CODES. Due to the diversity in state/provincial local, and federal laws and codes that govern the design and application of architectural products, it is the responsibility of the individual architect, owner, and installer to assure that products selected for use on projects comply with all the applicable building codes and laws. U.S. Aluminum exercises no control over the use or application of its products, glazing materials, and operating hardware and assumes no responsibility thereof. 10. EXPANSION JOINTS. Expansion joints and perimeter seals shown in these instructions and in the shop drawings are shown at normal size. Actual dimensions may vary due to perimeter conditions and/or difference in metal temperature between the time of fabrication and the time of installation. Gaps between expansion members should be based on temperature at time of installation. 11. COORDINATION WITH OTHER TRADES. Coordinate with the general contractor any sequence with other trades which offset curtain wall installation (i.e. fire proofing, back-up walls, partitions, ceilings, mechanical ducts, converters, etc.) 12. CARE AND MAINTENANCE. Final cleaning of exposed aluminum surfaces should be done in accordance with AAMA 609.1 for anodized aluminum and 610.1 for painted aluminum. 3
ORDER OF ASSEMBLY AND INSTALLATION FABRICATION CALCULATIONS... 5 PARTS IDENTIFICATION... 6-7 SITE PREPARATION... 8 DOOR WITH SIDELITE INSTALLATION... 9 Threshold Installation... 10 Sub Sill Track Installation... 11 Top Track and Header Installation... 12 Installation... 13 Top and Bottom Rail Installation... 14 Sidelite Glass Installation... 15 at Sidelite Installation... 16-17 at Wall Installation... 18 Cladding Installation... 19 TRANSOM DOOR INSTALLATION... 20 Transom Installation... 21 Transom Vertical Jamb Installation... 21 Transom Top Rail Installation... 22 Transom Header Installation... 22 Transom Glass Installation... 23 Support Fin Installation... 24 FIXED LITE INSTALLATION... 25 Fixed Lite Top and Bottom Rail Installation... 26 Fixed Lite Glass Installation... 27 Intermediate Vertical Mullion Installation... 28 DOUBLE DOOR WITH FRAME INSTALLATION... 29 DOOR INSTALLATION... 30 PERIMETER SEALING... 31 GLASS REPLACEMENT FOR DOORS... 32 Remove Damaged Glass... 32 Install Replacement Glass... 33-34 JOB SITE ESSENTIALS...35 4
FABRICATION CALCULATIONS FABRICATION DEDUCTIONS: Intermediate Vertical Mullion Sub Sill Top Anchor Track and Sidelite Rail (Wall to Doorway) Top Anchor Track and Sidelite Rail (Wall to Wall) DOOR SIZE: Door Height with Standard Header and Threshold Door Height with Recessed Flush Header (for Overhead Closer) and Threshold Door Width R.O. Height Minus 1-3/32 (27.8 mm) R.O. Height Minus 9-13/32 (238.9 mm) R.O. Height Minus 1/2 (12.7 mm) R.O. Width Minus 1/2 (12.7 mm) Minus 2-5/8 (66.7 mm) Minus 3 (76.2 mm) R.O. Height Minus 1-5/16 (33.3 mm) R.O. Height Minus 27/32 (21.4 mm) D.L.O. Minus (6.4 mm) Top Anchor Track Top Rail Header D.L.O. Door with Sidelite and Fixed Lite Rough Opening Height Intermediate Mullion Jamb Anchor Bottom Rail Sub Sill Threshold Rough Opening Width NOTE: R.O. = Rough Opening D.L.O. = Daylight Opening 5
ENTICE SERIES ENTRANCE SYSTEMS EXTERIOR GLAZE PARTS IDENTIFICATION 4 Square Door Rail Housing 4 Square Door Rail Clad 10 Door Rail Extension 2-5/8 Door Stile 2-5/8 Door Stile Clad Vertical Stile Vertical Stile Clad Stile Glass Attachment Strip Door / Mount Center Pivot Vertical Stile Center Pivot Vertical Stile Clad Header for Top Pivots Header Clad Half Saddle Threshold Offset Pivot Saddle Threshold Offset Pivot Saddle Threshold Center Pivot Half Saddle Threshold Center Pivot Threshold Offset Pivot End Cap Sidelite Rail Exterior and Interior Top Anchor Sidelite Rail Exterior Top Anchor / Interior Bottom Anchor Sidelite Rail Fastening Clip Sidelite Rail Setting Block 4 Square Sidelite Rail Housing 4 Square Sidelite Rail Clad For replacement parts, please contact Technical Sales at (800) 582-7501. 6
ENTICE SERIES ENTRANCE SYSTEMS EXTERIOR GLAZE PARTS IDENTIFICATION (CONTINUED) Sidelite Rail Exterior Bottom Anchor Transom Header Main Body Transom Header Main Body Clad Transom Header Main Body Clad Corner, and Transom Header Removable Stop Corner Main Body Clad Tall Corner Main Body Clad Short Corner Tall Interior Removable Stop L Clad Corner Short Interior Removable Stop L Clad Corner Main Body Main Body Vertical Mullion Main Body Vertical Mullion Removable Stop Vertical Mullion Removable Stop Clad Shear Clip Aluminum Clad OR Stainless Steel Clad Vertical Shear Clip PART # GH342 PART # NP238 Gasket Gasket PART # 20092003 PART # 10X112HHDTEK 10-16 X 5/8 Hex Washer Self Drilling Screw 10 X 1-1/2 Hex Washer Self Drilling Screw Corner Shear Clip Recessed Shear Clip 1 x 4 x 1/8 (25.4 mm x 101.6 mm x 3.2 mm) 65 +- 5 Durometer Neoprene Edge Block Setting Block 7
SITE PREPARATION 1. Review and measure the opening. 2. Verify rough window opening size 1/2 (12.7) clearance in both width and height to the window. Verify framing is plumb, straight, and true around window opening. Measure opening at each end and at center vertically and horizontally. Make corrections to openings as required. Measure opening diagonally to check squareness. Chip concrete high points to flush and rounded corners to square. Measure LEVEL VERTICAL DIMENSION Measure Measure SQUARE HORIZONTAL DIMENSION 8
DOOR WITH SIDELITE INSTALLATION 3 3 5 Door with Sidelite Installation Order 4 Sidelite 6 5 7 Door 10 8 1 Threshold Page 10 2 Sub Sill Page 11 3 Top Track and Header Page 12 4 Page 13 5 Top and Bottom Rail Page 14 6 Sidelite Glass Page 15 7 at Sidelite Page 16 8 at Wall Page 18 9 Cladding Page 19 10 Door Page 30 11 Finishing and Sealing Page 31 2 1 4 7 8 3 3 6 10 5 Exterior at Sidelite at Wall 5 Exterior 2 Sidelite Exterior 1 Door 9
THRESHOLD INSTALLATION 1. Determine the perimeter centerline of the opening and location of the bottom door spindle from the shop drawings. 2. Install the cement box and closer if applicable. 3. Apply a continuous bead of Cat. No. 33S Sealant to the floor substrate around the perimeter line below the threshold. Leave two weep gaps for water drainage and set threshold while sealant is wet. 4. Fasten the threshold to the floor with the appropriate fasteners as specified in the engineering requirements. Cover fastener heads with Cat. No. 33S Sealant. NOTE: For installations with doors, the threshold must be installed first to determine the location of the other components. Threshold is notched on each end for s that run through. Centerline Threshold Closer Drainage gaps in sealant Cat. No. 33S Sealant Exterior Threshold Options OR OR OR Half Saddle Threshold Offset Pivot Saddle Threshold Offset Pivot Saddle Threshold Center Pivot Half Saddle Threshold Center Pivot NOTE: Saddle Threshold Offset Pivot shown in illustrations. 10
SUB SILL TRACK INSTALLATION NOTE: Sub Sills are shipped with Fastening Clips installed in the track and End Dams sealed at each end. 1. Shim at each screw with Cat. No. PHS4 Horseshoe Shims turned parallel to Sub Sill. Position screws in center of slotted hole to allow for expansion. SUB SILL Fastening Clips and End Dams are factory installed. Use holes in Sidelite Rails as a guide for Clip placement. Maximum distance between clips = 9 (229 mm) Concrete Screw Part No. X 2-3/4 HWH TAPCON Non Slotted Hole next to Doorway SUB SILL Threshold is notched for Position Non Slotted Hole next to Doorway Jamb to prevent expansion into Doorway. Position screws in center of Slotted Holes. Insert Cat. No. PHS4 Shim. Turn to parallel. Do NOT block Weep Holes. 2. Seal over screw heads with Cat. No. 33S Sealant. NOTE: Do NOT block Weep Holes in Sub Sill. Cat. No. 33S. 11
TOP TRACK AND HEADER INSTALLATION TOP TRACK Fastening Clips must be installed before Sidelite Rails. Use holes in Sidelite Rails as a guide for placement. Maximum distance between clips = 9 (229 mm) TOP TRACK FASTENING CLIPS CUT SHORT CENTER DIRECTLY OVER SUB SILL HEADER MOUNT DIRECTLY ABOVE THRESHOLD 1. Level and mount Header directly above Threshold. 2. Slide Fastening Clips into each top track. Mount track directly above Sub Sill. Secure with screws centered in slots. Position screws in center of slotted holes. Turn PHS4 Shims parallel. Header is notched for. TOP TRACK Fastening Clip # 10 Fastener appropriate for substrate HEADER Sidelite SUB SILL THRESHOLD Door 12
WALL JAMB INSTALLATION 1. Fit the Main Body on the Sub Sill with the cladded side facing the interior. Push it tight against the End Dam and wall. 2. Shim and fasten to the wall. NOTE: Cladded side faces interior. Cladded Side Main Body with Gasket WALL JAMB SITS ON SUB SILL SUB SILL END DAMS DOORWAY JAMBS RUN THROUGH THRESHOLD # 10 Fastener appropriate for substrate Cladded Side Part No. GH342 Position screws in center of slotted holes. Turn PHS4 Shims parallel. WALL JAMB MAIN BODY (Assembled) # 10 Fastener WALL JAMB MAIN BODY Part No. GH342 WALL JAMB REMOVABLE STOP END DAM Exterior sits on Sub Sill tight against End Dam. 13
TOP AND BOTTOM RAIL INSTALLATION 1. Position Top and Bottom Rails with Shear Clips next to. 2. Position Fastening Clips to line up with holes in Top and Bottom Rails. Secure with 10X112HHDTEK drilling screws. NOTE: Do not block the drain slots placed between the mounting holes. Fastening Clips Header slotted for Top Rail Shear Clip attaches to Shear Clip Do not block Drain Slots. Part No. 10X112HHDTEK Bottom Rail Shear Clip attaches to Shear Clip Fastening Clips Threshold slotted for View from Interior NOTE: The Shear Clips also act as spacers for the cladding. These clips are used only where the Rail butts against a. Sidelite Rail Options 4 Sidelite Rail OR 10 Sidelite Rail Fastening Clip 10 Sidelite Rail Clip NOTE: 4 Rails shown in illustrations. 14
SIDELITE GLASS INSTALLATION 1. Trim edges of the glass at face and sides with a sharp utility knife to remove any excess Silicone Sealant. 2. Place Setting Blocks at quarter points in Bottom Rail and Edge Blocks at quarter points inside pocket. Neoprene Edge Block Setting Block 3. Lift and set glass into pocket. Position glass so one end is outside opening 1/2 (12.7 mm). 1 2 3 1/2 to 9/16 (5 to 14.3 mm) Glass Bite 1/2 to 17/32 (5 to 13.5 mm) Glass Bite 15
DOORWAY JAMB AT SIDELITE INSTALLATION 1. With Slotted Holes next to Top Rail, fit onto glass and lightly tap into place. 2. Secure Jamb to Top and Bottom Rail Shear Clips with Cap Screws. Slotted Holes at top Tighten Cap Screws into holes in Shear Clip Main Body Doorway Jamb NOTE: Spray glass edge with Cat. No. 1973 to prevent Gaskets from binding. Cap Screws secure Jamb to Sidelite Rails 3. Ensure glass is fully inserted into both Jambs. Tighten Cap Screws into holes in Shear Clip (Assembled) 1/2 (5 mm) Minimum Glass Bite CRITICAL ULTRA NARROW VERTICAL STILE 4. Fit Removable Stop to Main Body and secure with screws at all predrilled hole locations. Part No. GH342 WALL JAMB REMOVABLE STOP Part No. 20092003 Part No. GH342 WALL JAMB REMOVABLE STOP Removable Stop Exterior Main Body 16
DOORWAY JAMB AT SIDELITE INSTALLATION (CONTINUED) 5. Hand tighten Set Screws in to center glass in Sidelite Rails. Torque 1/8 turn past tight to secure. Included Hex Driver Doorway Jamb Set Screws can shift Jamb from side to side for centering on Sidelite Rail. 6. Roll NP238 Gaskets into both sides of Top and Bottom Rails using a CRL Vinyl Roller. Top Rail Top Rail Gasket Part No. NP238 Part No. NP238 Gasket Bottom Rail Bottom Rail Roll Gaskets into Rails Sidelite (Assembled) 17
DOORWAY JAMB AT WALL INSTALLATION 1. Mount Jamb Anchor to wall. Header Jamb Anchor Turn PHS4 Shims parallel. Position screws in center of slotted holes. Secure Jamb Anchor to wall. 2. Place and secure using the Set Screws on each side. Included Hex Driver Jamb Anchor with Jamb Anchor Slide against Jamb Anchor. Hand tighten Set Screws in Doorway Jamb evenly. Torque 1/8 turn past tight. at Wall (Assembled) ULTRA NARROW VERTICAL STILE # 10 Fastener appropriate for substrate JAMB ANCHOR 18
CLADDING INSTALLATION Remove liner from VHB Tape and apply Cladding. Roll On Pressure = 15 Pounds Per Linear Inch. at Sidelite at Wall Intermediate Mullion Transom Header Corner NOTE: Apply Cladding to Header before hanging doors. 19
TRANSOM DOOR INSTALLATION 1 4 8 3 6 3 8 Transom 5 Door 2 9 2 1 4 5 Transom Door Installation Order 1 Threshold and Top Track Pages 10, 12 2 Transom s Page 21 3 Transom Vertical Jambs Page 21 4 Transom Top Rail Page 22 5 Transom Header Page 22 6 Transom Glass Page 23 7 Cladding Page 19 8 Support Fins Page 24 9 Door Page 30 10 Finishing and Sealing Page 31 1 1 2 3 3 2 6 TOP TRACK 8 Interior 8 TOP TRACK FASTENING CLIPS CUT SHORT CENTER ABOVE TOP RAIL TRANSOM VERTICAL JAMBS SIT ON HEADER HEADER THRESHOLD DOORWAY JAMBS NOTCHED FOR HEADER AND TRANSOM VERTICALS 1. Follow instructions on Page 8 for Site Preparation, Page 10 for Threshold Installation, and Page 12 for Top Track Installation. 20
TRANSOM DOORWAY JAMB INSTALLATION 1. Install s with notched ends at top, facing the door opening. See Pages 16-18 for mounting options. NOTCHED END AT TOP FACING DOOR OPENING TRANSOM VERTICAL MAIN BODY Part No. GH342 Interior DOORWAY JAMB Shown without Jamb Anchor or glazing inserts. See Pages 16-17 for options. TRANSOM VERTICAL REMOVABLE STOP Transom Vertical (Assembled) (Notched) NOTE: body only is shown in illustrations. Doorway Jamb Doorway Jamb TRANSOM VERTICAL JAMB INSTALLATION 1. Align Transom Vertical Jamb Main Body with top of. Fasten with 10-24 X 3/4 Phillips PHMS screws. Align at top Transom Verticals ALIGN TO TOP TRANSOM VERTICAL MAIN BODY Transom Vertical Cladded side faces interior Secure with 10-24 X 3/4 Phillips PHMS Transom Vertical Doorway Jamb Part No. GH342 Cladded Side Doorway Jamb Doorway Jamb View from Interior Transom Header aligns with bottom notch. Transom Vertical sits on Header. 21
TRANSOM TOP RAIL INSTALLATION 1. Position Fastening Clips above holes in Top Rail and secure. Fastening Clips 4 Sidelite Rail Part No. 10X112HHDTEK TRANSOM HEADER INSTALLATION 1. Attach Left and Right Support Fin Bottom Fittings to each end of Transom Header Main Body. NOTE: Header ends are notched to accept Support Fins. Support Fins are installed on interior. Part No. GH342 Cladded Side TRANSOM HEADER REMOVABLE STOP TRANSOM HEADER MAIN BODY Transom Header (Assembled) Interior Support Fin Bottom Fitting Right Transom Header is notched at both ends. Part No. 10-16X3/4FHDSM Support Fin Bottom Fitting Left Transom Vertical 2. Match holes on s with holes of Support Fin Fitting and secure with screws. Transom Vertical Transom Vertical Transom Vertical Transom Header Transom Header Transom Header Part No. 10-16X3/4FHDSM View from Interior s Part No. 10-16X3/4FHDSM Views from Interior 22
TRANSOM GLASS INSTALLATION 1. Trim edges of the glass at face and sides with a sharp utility knife to remove any excess Silicone Sealant. 2. Place Setting Blocks 4 from each end of Transom Header and Edge Blocks at quarter points inside Transom Jamb Vertical pocket. Transom Vertical Jamb Transom Vertical Jamb Neoprene Edge Block Transom Header 3. Lift and set glass into pocket. Center. 4 (101.6 mm) 4 (101.6 mm) 4. Roll NP238 Gaskets into both sides of Top Rail using a CRL Vinyl Roller. 2 1 Transom Glass Transom Header Top Rail NP225 Gasket Top Rail Transom Glass 3 Part No. NP238 1/2 (5 mm) Minimum Glass Bite CRITICAL Transom Header Transom (Assembled) 5. Install Removable Stop for Header and then install Removable Stops for Transom Verticals. Secure with screws at all predrilled hole locations. TRANSOM VERTICAL REMOVABLE STOP Part No. GH342 Transom Vertical Doorway Jamb Transom Vertical Removable Stop Part No. GH342 TRANSOM VERTICAL REMOVABLE STOP Part No. 20092003 Part No. GH342 2 Transom Vertical Main Body 2 TRANSOM HEADER REMOVABLE STOP TRANSOM HEADER REMOVABLE STOP Part No. 20092003 Transom Header Main Body Part No. 20092003 Transom Header 1 1 Transom Header Removable Stop View from Exterior 23
SUPPORT FIN INSTALLATION NOTE: Go to Page 19 to install Cladding before proceeding with the Support Fin Installation. Ceiling Fin Mounting Bracket Sex Bolt Shanks Vinyl Insert Sex Bolts Nylon Grommets Flat Head Screws Fasteners supplied by others Gasket Position Mounting Bracket flush against cladded s. Secure to ceiling. Install Nylon Grommets in top holes and slide glass into Mounting Bracket. Secure. Fitting Cover Nylon Grommet Gasket Clamping Plate Sex Bolt Sex Bolt Shank Fitting Cover Insert Nylon Grommet in bottom hole. Position Clamping Plate and Gasket. Secure. Remove paper from Double Stick Tape and apply Fitting Covers. 24
FIXED LITE INSTALLATION 1 3 1 2 4 Fixed Lite Fixed Lite 5 4 2 4 5 4 3 3 Fixed Lite Installation Order 1 Sub Sill and Top Track Pages 11, 12 2 s Page 13 3 Top and Bottom Rail Page 26 4 Fixed Lite Glass Page 27 5 Intermediate Mullion Page 28 6 Cladding Page 19 7 Finishing and Sealing Page 31 3 1 1 Fixed Lite 2 5 2 4 4 Exterior Intermediate Mullion TOP TRACK FASTENING CLIPS CUT SHORT CENTER DIRECTLY OVER FASTENING CLIPS SUB SILL INTERMEDIATE MULLION FITS BETWEEN TOP AND BOTTOM RAILS WALL JAMB SITS ON SUB SILL BOTTOM RAIL SUB SILL END DAMS WALL JAMB SITS ON SUB SILL 1. Follow instructions on Page 8 for Site Preparation and Pages 11-12 to install Sub Sill and center Top Track above it. (Top Track is cut 1/2 (12.7 mm) short.) 2. Follow instructions on Page 13 to install s. 25
FIXED LITE TOP AND BOTTOM RAIL INSTALLATION 1. Attach Vertical Shear Clips at Intermediate Mullion position on Top and Bottom Rails. 2. Position Fastening Clips above holes in Top and Bottom Rails and secure. TOP RAIL Fastening Clips 4 Sidelite Rail Part No. 10X112HHDTEK Part No. 10X112HHDTEK Vertical Shear Clips Do not block Drain Slots. BOTTOM RAIL Vertical Shear Clips Part No. 10X112HHDTEK Fastening Clips 4 Sidelite Rail 26
FIXED LITE GLASS INSTALLATION 1. Trim edges of the glass at face and sides with a sharp utility knife to remove any excess Silicone Sealant. 2. Place Edge Blocks at quarter points inside Wall Jamb Vertical pockets and Setting Blocks at quarter points in each section of Bottom Rail. Neoprene Edge Blocks Setting Blocks 3. Lift and set each glass panel into pocket and center. 1 Fixed Lite Glass Fixed Lite Glass 3 1/2 (5 mm) Minimum Glass Bite CRITICAL 2 4. Place Removable Stop on Main Body and secure with screws at all predrilled hole locations. Main Body WALL JAMB REMOVABLE STOP Part No. GH342 Part No. 20092003 Interior Part No. GH342 WALL JAMB REMOVABLE STOP Part No. 20092003 Part No. 20092003 Exterior Removable Stop 27
INTERMEDIATE VERTICAL MULLION INSTALLATION Part No. GH342 Interior INTERMEDIATE MULLION MAIN BODY Part No. GH342 Part No. GH342 INTERMEDIATE MULLION MAIN BODY INTERMEDIATE MULLION REMOVABLE STOP 1. Fit Vertical Mullion Main Body between Vertical Shear Clips. INTERMEDIATE MULLION REMOVABLE STOP Part No. 20092003 2. Fit Removable Stop and secure with screws at all predrilled hole locations. Intermediate Mullion Main Body Vertical Shear Clips Intermediate Mullion Removable Stop Intermediate Mullion Main Body Intermediate Mullion Removable Stop Vertical Shear Clip Part No. 20092003 Exterior Bottom Rail Exterior 3. Roll NP238 Gaskets into both sides of Top and Bottom Rails using a CRL Vinyl Roller. Top Rail Gasket Top Rail Gasket Top Rail Part No. NP238 Part No. NP238 Gasket Gasket Bottom Rail Bottom Rail Bottom Rail Roll Gaskets into Rails Fixed Lite (Assembled) 28
DOUBLE DOOR WITH FRAME INSTALLATION 2 Door Door 3 4 4 3 Double Door with Frame Installation Order 1 Threshold Page 10 2 Header Page 12 3 s Page 18 4 Cladding Page 19 5 Door Page 30 6 Finishing and Sealing Page 31 1 3 3 2 4 4 at Wall Exterior at Wall Exterior 1 Door 29
DOOR INSTALLATION The doors for the Entice System are shipped fully assembled. Because of the weight of both the aluminum and the glass, it is advisable that two individuals are involved in moving and installing this door. NOTE: Installation varies with hardware selection. Consult Installation Instructions in hardware packages. Use included T-Handle Key to turn the adjustment screws on the top and bottom of the hinge side of the door. With the door open, turn clockwise to adjust the Door Rail away from the jamb and counter-clockwise to adjust the Door Rail towards the jamb. Make sure the gaps are parallel and the correct size. NOTE: A slight clicking noise may be heard. This sound is caused by our friction retention mechanism that will help prevent the screw from loosening out of alignment. CENTER PIVOT DOORS: To center the door, loosen the two Pan Head Phillips Screws holding the arm to the block, then adjust the two hex bolts at the end of each arm to slightly change the angle of the arm as it mounts in the Door Rail. Make sure that both hex bolts are tightened against the inside face of the Door Rail, and the two Pan Head Phillips Screws are tightened to the block when adjustment is complete to secure the adjustments into place. 30
PERIMETER SEALING 1. Seal around at Threshold. Seal around at notched Threshold with Cat. No. 33S Clear Silicone. 2. Seal joints between Bottom Rail and Sub Sill inside and outside. Bottom Rail Cat. No. 33S Clear Cat. No. 33S Clear Cat. No. 95C Black Shim Sub Sill Backer Rod Cat. No. 95C Black Threshold 3. Install Backer Rod and seal perimeter with Cat. No. 95C Silicone Sealant at all shimmed areas inside and outside. Cat. No. 95C Black Cat. No. 95C Black 4. Seal interior perimeter at all verticals 2 (203 mm) up from ground where they meet Bottom Rails. Backer Rod Backer Rod 2 (50.8 mm) Cat. No. 95C Black at Wall Cat. No. 95C Black 2 (50.8 mm) Interior Cat. No. 33S Clear Cat. No. 33S Clear 5. Seal outside bottom corners where all verticals meet Bottom Rails. Intermediate Mullion Cat. No. 33S Clear Cat. No. 33S Clear Exterior Bottom Rail Cat. No. 33S Clear Bottom Rail Cat. No. 33S Clear Bottom Rail Exterior 31
GLASS REPLACEMENT FOR DOORS REMOVE DAMAGED GLASS Support door on sturdy sawhorses. NOTE: Handle Cladding with care so as to not bend or scratch it. Remove door handles and panic or exit devices and store in a safe place. Remove Cladding from both sides of Vertical Stiles. Loosen Set Screws on both sides of Vertical Stiles. Back out Clamping Screws on Top and Bottom Rails. Remove Socket Head Cap Screws from each corner. Remove Vertical Stiles and Top and Bottom Rails. If Gaskets are not in good condition, remove them. If replacing Top and Bottom Rail Cladding, do so now. 32
INSTALL REPLACEMENT GLASS Verify replacement glass size and mounting hole placement for handles. Place Top and Bottom Rails and tighten Clamping Screws. NOTE: Ensure Rails are properly supported until secured to Vertical Stiles. Vertical Stile Install replacement gasket Clamping Strip Gasket Housing Replace Gaskets in Vertical Stiles if needed. Spray glass edges with Cat. No. 1973 to prevent Gaskets from binding and install Vertical Stiles. Blue Loctite NOTE: The Vertical Stiles may be installed as three separate pieces. First apply the Clamping Strip to the glass, then fit the Gasket Housing over it and finally slide the Vertical Stile over it. This works well with oversized glass thickness. Ensure Stiles are Straight Apply Blue Loctite to Socket Head Cap Screws and fasten Vertical Stiles to Top and Bottom Rails. Rubber Setting Block inside Bottom Rail Hinge Side Vertical Stile Ensure Bottom Rail is tight against glass Push frame at bottom to ensure Setting Block is in contact with glass. Ensure Bottom Rail is tight against glass and Vertical Stiles are straight. Tighten Set Screws evenly on Hinge Side of the Vertical Stiles. Torque 1/8 turn past tight. 33
242 THREADLOCKER 24231 ENTICE SERIES ENTRANCE SYSTEMS EXTERIOR GLAZE INSTALL REPLACEMENT GLASS (CONTINUED) Measure Diagonally Use Adjuster to raise Handle Side corner 1/8 (3.2 mm) Handle Side Vertical Stile Turn Adjuster in Top Rail on Handle Side clockwise until it contacts glass. Measure diagonally to corners. If needed, turn Adjuster again to raise corner a maximum of 1/8 (3.2 mm) until door is square. Tighten Set Screws evenly on Handle Side of the Vertical Stiles. Torque 1/8 turn past tight. Measure Between Stiles Blue Loctite Measure between Vertical Stiles near Bottom Rail and again at middle to ensure Stiles are straight. Apply Blue Loctite on all attachment fasteners and install door handles. Follow instructions on Page 29 to install and adjust door. Use Adjuster to raise Handle Side corner 1/8 (3.2 mm) NOTE: If Handle Side sags, loosen Set Screws and turn Adjuster to raise. Then tighten Set Screws. Remove liner from VHS Tape and apply Cladding to Vertical Stiles. Roll On Pressure = 15 Pounds Per Linear Inch 34
JOB SITE ESSENTIALS Helpful Tools and Supplies for Installing CRL U.S. Aluminum Entrances, Storefronts, Windows, and Curtain Wall Systems CRL 95C Silicone Building Sealant CAT. NO. 95C CRL RTV408 Neutral Cure Silicone CAT. NO. RTV408 CRL33S Silicone Sealant CAT. NO. 33S CRL12:1 Ratio Strap Frame Caulking Gun CAT. NO. GA1203 CRL Complete Set of Seven All Stainless Steel Spatulas CAT. NO. AB958G CRL Open Cell Backer Rod CAT. NO. B0CBR58C CRL Backer Rod Roller Tool CAT. NO. SBRR CRL Glass Cleaner CAT. NO. 1973 CRL Glass Wipes CAT. NO. 1550 CRL Clear Loctite Poxy-Pak Two- Part Epoxy CAT. NO. 81120 CRL 1.69 Fl. Oz. (50 ml) Bottle Loctite Threadlocker CAT. NO. 24231 CRL Plumb Bob Alignment Tool for Premium Balanced Doors CAT. NO. BDPS105 35