Experiment 1: Fraunhofer Diffraction of Light by a Single Slit Purpose 1. To understand the theory of Fraunhofer diffraction of light at a single slit and at a circular aperture; 2. To learn how to measure the intensity distribution of the diffracted light by a single slit; 3. To learn how to measure the radius of the wire by the diffraction method. Apparatus Laser, diffracting objects (including a single slit, a circular aperture, a wire), lens, photocell, resistance box, MCDF20 single slit diffraction set, oscilloscope Theory "Diffraction" refers to the spreading of waves and appearance of fringes that occur when a wave front is constricted by an aperture in a screen that is otherwise opaque. The Huygens-Fresnel principle governs diffraction phenomena: "Every unobstructed element of a wavefront acts as a source of spherical waves with the same frequency as the primary wave. The amplitude of the optical field beyond is a superposition of all these wavelets taking account of their amplitudes and phases." When both the light source and the viewing plane are effectively at infinity with respect to the diffracting aperture,in this case, the incident light is a plane wave so that the phase of the light at
each point in the aperture is the same. The phase of the contributions of the individual wavelets in the aperture varies linearly with position in the aperture, this is the Fraunhofer approximation. In practice the diffraction pattern is viewed at a long distance from the diffracting object, or at the focal plane of an imaging lens. 1. Fraunhofer diffraction at a single slit Alternately dark and bright fringes will be observed at the viewing plane when parallel light is diffracted by a single slit. As shown in Fig. 1, the Fraunhofer diffraction pattern has maximum intensity at the central location which is determined by the rectilinear propagation law of light, and a series of peaks of decreasing intensity and width on each side symmetrically. The intensity distribution of the diffracted light, is given by where is the width of slit, is the diffraction angle, is light wavelength, and A is a factor for maximum intensity. The pattern is shown in the image together with a plot of the intensity vs. angle θ. Most of the diffracted light falls between the first order minima (Fig. 1). Two conclusions can be drawn herewith (1) Dark fringes correspond to zero intensities of the diffracted light, i.e.
(2) Diffraction angles corresponding to secondary maxima are determined by with normalized light intensities of respectively. Figure 1: The Fraunhofer diffraction pattern 2. Fraunhofer diffraction at a circular aperture The Fraunhofer diffraction pattern given by a circular aperture is characterized by concentric circles. The concentric intensity distribution of the diffracted light, is given by In which and b is the radius of the aperture.
It can be seen that most of the light is in the central disk. The angle subtended by this disk, known as the Airy disk, is determined according to the formula of. 3. Diffraction by objects with mutually complementary shapes Consider two diffracting bodies with mutually complementary shapes, let A be the original one, and B its complement, i.e. the body that is transparent where A is opaque, and opaque where B is transparent. Suppose and are electric fields for diffracted light by A and B on the surface of the viewing plate, because no diffracted light can reach to the viewing plate if both A and B are assembled, therefore,. This means that the sum of the radiation patterns caused by A and B must be the same as the radiation pattern of the undisturbed beam. In places where the undisturbed beam would not have reached, this means that the radiation patterns caused by A and B must be opposite in phase, but equal in amplitude, this is the Babinet's principle. Diffraction patterns from apertures or bodies of known size and shape are compared with the pattern from the object with equivalence in size and shape to be measured. Consequently, diffraction pattern of a single slit with a width of a is usually used to detect the diameter a of a wire. Experiment As shown in Fig. 2, a monochromatic laser beam is used as the incident light. The intensity of the diffracted light is measured with a photodiode or a CCD.
Figure 2: Arrangement for Fraunhofer Diffraction 1. Light intensity detection by a photocell The shot-circuit current (photocurrent) of the silicon photocell is proportional to the incident light intensity. The detector will be shifted in the direction perpendicular to slit during the experiment, in order to measure light intensity distribution in the observation screen. Weak photocurrent is determined by recording the deflection amplitude, which is also proportional to the light intensity, of the light spot on the transparent window of a galvanometer. Tune the hand screw to slide the photocell and analyzing slit along a calibrated translation stage so that the detailed shape of the diffraction pattern can be discerned. By carefully shifting the detector, central bright fringe can be located. The revolution counter reading at this point is taken as the origin. By adjusting a load resistor or adjusting slit width, the initial division reading of the galvanometer is set to be about 80. The photocell should be shifted to one side (either left side or right side) at first, so as to ensure that all the intensities near the central maximum will be
recorded in the following measurement. Begin intensity measurement in a 0.2mm step, record both the position and the intensity readings x, n, until the secondary dark fringe is covered. Be sure to tune the screw always in one direction during measurement, in order to avoid inaccuracy of position readings caused by the backlash errors of the actuating mechanism. 2. Light intensity detection by a CCD detector As shown in Fig. 3, the measuring system includes laser, analyzing slit, CCD detecting set and oscilloscope, etc. The CCD detecting set consists of a pair of polarizers, CCD detector, driving circuit, signal processing unit and power supply. The polarization direction of polarizers, one of which is fixed, and another is adjustable, can be adjusted to attenuate light that is incident on the CCD detector. The signal output of CCD is a chain of electric pulses corresponding to light intensities (in form of voltages) generated by each pixels. After amplification and filtering, time-dependent voltage signal is generated in sequence of the pixel order. An one-dimensional spatial distribution of the diffracted light can be displayed in the mode of T-V on the oscilloscope. Figure 3: Intensity detection using CCD
Essentials of adjustment (1) Connection of an oscilloscope to the measuring system A dual-channel oscilloscope is used in experiment. Connect the output end labeled signal of the measuring system to CH1, another one labeled Trigger to CH2 in the instrument. Set the triggering level, the scale divisions for CH1, CH2 and time properly so that stable triggering pulses can be fully displayed on both sides of the observation screen of the oscilloscope. (2) Light path adjustment Align the laser, slit and CCD detector to be equal in altitude and coaxial. With the laser on, carefully adjust the polarizer until the diffraction pattern is clearly visible on the entrance window of CCD detector. Further adjustment may be required in order to display the intensity distribution of the diffracted light on the oscilloscope. Locate the central peak right in the middle on the screen. If the intensity curve turns to be flattened out in case of too strong incident light, the polarizer should be rotated gradually again, in order to reduce light irradiance on the photosensitive surface of the CCD. (3) Measurement of light intensity The curve displayed on the screen of the oscilloscope corresponds to relative intensity distribution. Take note of the coordinates on the distribution curve at 15-20 arbitrary transverse positions and convert them into spacing. Measure the distance between the slit and the CCD detector. Draw a line chart showing the relationship of relative intensity to the diffraction angle, i.e., on graph paper.
Caution: 1. Avoid direct incident of laser beam on the CCD detector. 2. Carefully clean the polarizers in a way similar to optical lens cleaning and do not touch them directly with your fingers or hands. 3. Carefully change the polarization direction by gradually and slowly rotating the polarizer during experiment. Primary requirements 1. Use photocell to detect the diffracted light, measure photocurrents of the photocell at different locations from the central maximum to the secondary bright stripe. Draw a graph of, and calculate the slit width a. Repeat the measurements to get the average value of a. Compare the averaged slit width a with that measured by means of a reading microscope. 2. Use CCD as a detector, observe the diffracted light distribution pattern on an oscilloscope, record experimental data and draw a graph of. Compare a once again. 3. (optional) Try to get the diffraction pattern of the circular aperture, determine the position for the first minimum (i.e. the radius of the Airy disk), and, finally, calculate the radius of the circular aperture. 4. (optional) Try to measure radius of a thin wire by means of the diffraction method.
Problems 1. What kind of influence on the diffraction pattern to be expected when factors such as width and orientation of the single slit, and distance of the viewing plate away from the slit are concerned? 2. If red and blue lights are used simultaneously, will their central maxima overlap? And will the secondary bright fringes overlap? Give reasons. 3. What kind of influence on the diffraction pattern to be expected when wavelength of the incident light is too long or too short?