Phil s Mk2 Jag body repairs

Similar documents
Please read these instructions all the way through before starting, since the order of work is important.

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS

Installation Instructions for Lambo Door Mechanism. 1. Lift the hood and remove left and right shield of front wheel.

BILLET SUICIDE HINGE INSTALL INSTRUCTIONS

Chevy Pickup / Suburban / Blazer Set Part # Rev B 5-04

Bolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.

Body Repair. Collision Repair. Specification. Fastener Specifications Fastener Specifications. Blind Rivet. Flow Drill Screw (FDS) Torque FDS

BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions

TUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS MUSTANG

Jeep Cherokee Door XJ Set Part # Revision J

SAFETY. Read and understand all safety precautions and instructions before installing this product.

Page 1 of 12 GENERAL INSTRUCTIONS KHJKK Installation

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Chevrolet Cut-Out Fender Flares Set of 4

Table of Contents F Series Frames

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Chevrolet Cut-Out Fender Flares Set of 4

Jeep Cherokee 4-Door XJ Set Part # Rev

TRANSIT 148 HIGH ROOF WALL LINERS INSTALLATION INSTRUCTIONS

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit:

Included in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION

GMC Cut-Out Fender Flares Set of 4

INSTRUCTION SHEET U19

THE 229-A SERVICE BODY WOOD DIMENSIONS. By Neil Wilson of Boulder, Colorado February 6, Baseline Structure

Dodge Dakota 2005 Quad Cab Set Part # Revision A

Chevrolet Cut-Out Fender Flares Set of 4

Toyota FJ Cruiser 2006-Up Set Part # Revision A

FENDER FLARE INSTALLATION

#2010 #1795. Frame Rack Dyna Mo Clamps Two pair of jaws with 12 draw bar. Grip surface 9-¼ wide. #1929 #1910

D. Drill Bolt Holes Through Topper Shell and Bed Rails

Included in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION:

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION

OTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE.

GMC Cut-Out Fender Flares Set of 4

Cut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

PROMASTER 136 WB LOW ROOF WALL LINERS INSTALLATION INSTRUCTIONS

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:

Please read the instructions completely BEFORE starting this project.

Clayton Off Road COR COR COR

Rubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs

Please read the instructions completely BEFORE starting this project.

Ford Cut-Out Fender Flares Rear Pair

Included in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:

20011, F100 - F150 - F250 - F350 P.U. & BRONCO Tools Needed for Installation:

MGB Sill Replacement

Detroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit Camaro/Firebird P/N:

INSTALLATION INSTRUCTIONS

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :

Chevrolet Cut-Out Fender Flares Front Pair

INSTALLATION INSTRUCTIONS 10-POINT ROLL CAGE. Please read the instructions completely BEFORE starting this project.

INSTALLATION INSTRUCTIONS

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016

Toyota Extend-A-Fender Fender Flares Set of 4

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)

INDEPENDENT FRONT SUSPENSION SWAP

Included in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Be sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.

*DO NOTE USE: Loctite, SuperGlue, or similar products on the hardware or the fl ares.

Ford Pocket Style Fender Flares Set of 4

Ford F150 Rear Flares Set Part # Revision

Detroit Speed, Inc. Heavy Duty Leaf Spring Pocket Kit X-Body P/N:

Part# C3135/C Up Challenger 8-Point Roll Bar

GMC Extend-A-Fender Fender Flares Set of 4

Ford Cut-Out Fender Flares Front Pair

SS13R SAFARI R-SPEC SNORKEL Nissan GQ Patrol with 4.2L TD42 Diesel Engine and Horizontal Pre-Cleaner.

Ford Cut-Out Fender Flares Front Pair

Introduction: The Eldorado is a classic Cadillac that is fast becoming a collectable and appreciat

INSTALLATION INSTRUCTIONS 2008-up Challenger 10-POINT ROLL CAGE C3235 / C3285. Please read the instructions completely BEFORE starting this project.

8561 / 8569 DODGE AAM FRONT AXLE C-GUSSET KIT

F-SERIES BODY INSTALLATION REGULAR CAB DOOR OPENING PANEL - SERVICE KIT INSTRUCTIONS

Toyota Pocket Style Fender Flares Set of 4

Bolt-On/Rugged Fender Flares GMC Sierra 1500/2500/3500 (14-ON) Important: Please read instructions entirely before installing this product.

NVH KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 06/15 Page 1 of 5 RANGER 900 XP

INSTALLATION INSTRUCTIONS 8-POINT ROLL BAR (TRUCK) Please read the instructions completely BEFORE starting this project.

Toyota Cut-Out TM Fender Flares Set of 4

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K

Ford Cut-Out Fender Flares Front Pair

Chevrolet Cut-Out Fender Flares Front Pair

Fig A 2. Using a 10mm Socket, remove the two bolts referenced in (Fig B). Save these bolts for reuse. Fig B ADDICTIVE DESERT DESIGNS.

WATSON RACING 4- & 6-POINT ROLL BAR Mustang Coupe p/n WR-15-BOLTINCAGE p/n WR-15-BOLTINCAGE6PT

TECHNICAL DATA SHEET STANDARD STEEL FRAMES SPECIFICATIONS MESKER STANDARD STEEL FRAMES

Ford Cut-Out Fender Flares Set of 4

Toyota Tacoma Extended Cab/Standard Cab Set Part # Rev

Tech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.

GMC Cut-Out Fender Flares Front Pair

GMC Extend-A-Fender Fender Flares Set of 4

General Prisoner Transport Install Instructions PT-2-INST

Isuzu D-Max Part Numbers Black Polished

STEP 1 PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:

K9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS

Chevrolet Street Flares Fender Flares Set of 4

BODY REPAIR SECTION BRM CONTENTS BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY BRM-1 FUNDAMENTALS SERVICE INFORMATION FOREWORD... 5 Foreword...

Assembly & Installation Instructions FOR VEHICLE MOUNT KIT USING VEHICLE CENTER MEMBER

Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)

Hiniker Company th St. P.O. Box 3407 Mankato, MN VEHICLE INSTALLATION INSTRUCTIONS FOR: CHEV/GMC 4x4: K1500 SILVERADO/SIERRA

ASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND GM FLUSH TAILGATE WITH HANDLE

INSTALLATION GUIDE TOYOTA 4 RUNNER (2013+) REAR BUMPER

Installation Instructions Universal Crossmember Kit - 60 Track Width BEFORE Measure Twice, Weld Once! II

Toyota Extend-A-Fender Fender Flares Set of 4

NISSAN T30 X-TRAIL WITH SUNROOF CARGO BARRIER FITTING INSTRUCTION PART NO YEARS OF MANUFACTURE MAY 2002 ONWARDS.

Transcription:

Phil s Mk2 Jag body repairs Repair Description Parts ref () R/H front fender (Lower inner A pillar area) Behind front wheel R/H front fender (Outer skin) Behind front wheel, lower outer skin. R/H inner front wheel arch (splash panel) Wheel arch lip R/H area forward of front wheel R/H inner sill Cut and remove old unwanted areas at bottom of A pillar. Fabricate new sections as required and weld in place. Additional welds needed to existing repairs on inner. Cut and remove remains of lower outer skin. Trim and fit new lower patch /repair panel. Tack weld in place and test fit door. Grind and finish existing welds. Additional welds needed to existing repairs. Straighten existing inner splash panel. Additional welds needed to existing repairs. Clean and grind welds as required. a) Cut rusted areas from above bumper mount on inner panel. b) Cut rusted areas from out rigger and front of crows foot. Grind and finish existing welded repairs on inner sill (under side of car). Cut rusted areas from inside rear end of sill. MRK12RH (wheel arch front wing)

R/H rear jacking point R/H front jacking point Repair Description Parts ref () R/H A pillar area (Above top hinge area) R/H B pillar, lower area at joint to sill R/H outer sill panel Grind and clean up existing welds on inside floor of car. Cut and remove rusted section includes inner skin and outer lip of door opening. Grind and finish welds Cut/remove rusted area at bottom of B pillar at joint to top of sill. Fabricate new section and weld in place. Cut and remove remains of old outer sill. Grind and clean up surfaces. Test fit doors and align. Cut new sill to fit vehicle, tack weld in place. Check alignment and fully weld in place. MRK19RH MRK18RH The Surgery (rear jacking point) (front jacking point) MRK20RH (Outer sill panel, full sill with step)

() R/H rear quarter panel, behind rear wheel L/H rear quarter panel, behind rear wheel L/H inner sill area (forward of rear wheel) L/H rear jacking point L/H front jacking point: L/H inner front wheel arch (splash panel) L/H outer sill panel Cut remove existing old repair from outer panel. Cut rusted inner section from car. Fabricate new inner and weld in place. Fabricate new outer section, align to spat and fully weld in place. Cut rusted outer section from car. Fabricate new outer section, align to spat and fully weld in place. Cut and remove rusted section. Trim and fit new patch /repair panel. Cut and remove remains of old outer sill. Grind and clean up surfaces. Test fit doors and align. Cut new sill to fit vehicle, tack weld in place. Check alignment and fully weld in place. MRK19LH MRK18LH MK11LH MRK20LH The Surgery (rear jacking point) (front jacking point) (baffle splash panel) (Outer sill panel, full sill with step)

() L/H B pillar, lower area at joint to sill L/H A pillar area (lower area inside door opening at joint to front of sill) L/H A pillar area (Above top hinge area) L/H front fender (Lower inner A pillar area) Behind front wheel L/H front fender (Outer skin) Behind front wheel, lower outer skin Cut/remove rusted area at bottom of B pillar at joint to top of sill. Fabricate new section and weld in place. Cut and remove rusted section. Cut and remove rusted section includes inner skin and outer lip of door opening. Cut rusted area and old repair on outer skin of fender. Fabricate new sections, tack weld in place and test fit. Cut and remove old rusted areas at bottom of A pillar. Fabricate new sections as required align and weld in place. Clean and grind welds as required. Cut and remove remains of lower outer skin. Trim and fit new lower patch /repair panel. Tack weld in place and test fit door. MRK12LH (wheel arch front wing) L/H area forward of front wheel: Drill and grind spot welds to remove existing front out rigger. Clean up surfaces align and fully weld in place.

() L/H front fender light pod: Other parts purchased Cut and remove rusted sections from both inner and outer skins. Cutaway spats (LH and RH) MRK29ALH/RH LHF Door Skin (3/4) MRK16LHF LHR Door skin (3/4) MRK16LHR RHF Door skin (3/4) MRK16RHF The Surgery RHR Door Skin (3/4) MRK16RHR The Surgery