Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 600~8000W U Distributed Power/Charger System RHP-U Rack System File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System SPECIFICATION - Power Supply System MODEL OUTPUT INPUT FUNCTION NOTE RECTIFIER RACK SHELF OUTPUT OLTAGE RHP-8KU - RHP-8KU -4 RHP-8KU -48 RCP-600- RCP-600-4 RCP-600-48 RHP-UI-A or RHP-UT-A MAX. OUTPUT CURRENT 65A 335A 67.5A MAX. OUTPUT POWER Note.5 7500W 8040W 8040W OLTAGE RANGE Note.6 90 ~ 64AC 7 ~ 370DC FREQUENCY RANGE 47 ~ 63Hz AC CURRENT (Typ.) per RECTIFIER 4A/5AC 8A/30AC 5A/5AC 8.5A/30AC 5A/5AC 8.5A/30AC LEAKAGE CURRENT per RECTIFIER <.5mA / 30AC Note.8 OUTPUT OLTAGE PROGRAMMABLE(P) Adjustment of output voltage is allowable to 40 ~ 5% of nominal output voltage(60~5% for ). Please refer to the Function Manual. CONSTANT CURRENT LEEL PROGRAMMABLE(PC) Adjustment of constant current level is allowable to 0 ~ 00% of rated current. Please refer to the Function Manual. REMOTE ON-OFF CONTROL By electrical signal or dry contact ON:short OFF:open ALARM SIGNAL WORKING TEMP. WORKING HUMIDITY ENIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT IBRATION SAFETY & EMC (Note 4) OTHERS REMOTE SENSE Compensate voltage drop on the load wiring up to 0.5 AUXILIARY POWER 5 @ 0.3A, @ 0.8A SAFETY STANDARDS WITHSTAND OLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY 4 Isolated TTL signal output for T-Alarm, AC-OK and DC-OK -30 ~ +70 (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH non-condensing ± 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL60950-, TU EN60950- approved I/P-O/P:3KAC I/P-FG:KAC O/P-FG:.5KAC (0.5KAC for ) I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500DC / 5 / 70% RH Parameter Standard Conducted Radiated Harmonic Current oltage Flicker EN5504, EN604-3, EN6000-6- Parameter ESD Radiated EFT / Burst Surge Conducted Magnetic Field oltage Dips and Interruptions EN550 (CISPR) / EN550 (CISPR) EN550 (CISPR) / EN550 (CISPR) EN6000-3- EN6000-3-3 Standard EN6000-4- EN6000-4-3 EN6000-4-4 EN6000-4-5 EN6000-4-6 EN6000-4-8 EN6000-4- DIMENSION Rack 365*48.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket) PACKING 5.5Kg; 3pcs/7.5Kg/.CUFT 48 Test Level / Note Class B Class A Class A ----- Test Level / Note Level 3, 8K air ; Level, 4K contact Level 3 Level 3 Level 4, K/Line-Line K/Line-Earth Level 3 Level 4 >95% dip 0.5 periods, 30% dip 5 periods, >95% interruptions 50 periods File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System SPECIFICATION - Charger System MODEL RHB-8KU - RHB-8KU -4 RHB-8KU -48 CHARGER RCB-600- RCB-600-4 RCB-600-48 RACK SHELF RHP-UI-A or RHP-UT-A OUTPUT BOOST CHARGE OLTAGE(boost)(default) 4.4 8.8 57.6 FLOAT CHARGE OLTAGE(float)(default) 3.8 7.6 55. CURRENT RANGE 0 ~ 500A 0 ~ 75A 0 ~37.5A OLTAGE RANGE Note. 90 ~ 64AC 7 ~ 370DC FREQUENCY RANGE 47 ~ 63Hz INPUT AC CURRENT (Typ.) per CHARGER 4A/5AC 8A/30AC 5A/5AC 8.5A/30AC 5A/5AC 8.5A/30AC LEAKAGE CURRENT per CHARGER <.5mA / 30AC Note.5 OUTPUT OLTAGE PROGRAMMABLE(P) Adjustment of output voltage is allowable to 75 ~ 5% of nominal output voltage. Please refer to the Function Manual. OUTPUT CURRENT PROGRAMMABLE(PC) Adjustment of output current is allowable to 0 ~ 00% of rated current. Please refer to the Function Manual. FUNCTION REMOTE ON-OFF CONTROL By electrical signal or dry contact ON:short OFF:open AUXILIARY POWER 5 @ 0.3A, @ 0.8A ALARM SIGNAL The isolated TTL signal out, Please refer to Installation Manual TEMPERATURE COMPENSATION -3m / / cell / ( = 6 cells ; 4 = cells ; 48 = 4 cells) ENIRONMENT WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT IBRATION -30 ~ +70 (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-, TU EN60950- approved SAFETY & WITHSTAND OLTAGE I/P-O/P:3KAC I/P-FG:KAC O/P-FG:.5KAC (0.5KAC for ) EMC (Note 4) ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500DC / 5 / 70% RH Compliance to EN550 (CISPR) Conduction Class B, Radiation Class A ; EN6000-3-,-3 EMC IMMUNITY Compliance to EN6000-4-,3,4,5,6,8,, EN6000-6- (EN5008-), light industry lev el, criteria A OTHERS DIMENSION Rack 365*48.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket) PACKING 5.5Kg; 3pcs/7.5Kg/.CUFT NOTE File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System Function Manual. oltage Drop Compensation (Only for power supply system). Remote Sense The remote sense compensates voltage drop on the load wiring up to 0.5. RHP-U System CN + +S -S - + - LOAD Sense lines should be twisted in pairs. Local Sense Notice : The +S,-S have to be connected to the +(signal),-(signal),respectively, in order to get the correct output voltage if the remote sensing is not used. RHP-U System CN + +S - -S 3 4. Output oltage Programming (or, P / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed by applying EXTERNAL OLTAGE. CN +S + - RHP-U System -S P CN - signal LOAD 6 EXTERNAL OLTAGE (DC) 4 +S & +, -S & - also need to be connected on CN. (Only for power supply system) OUTPUT CURRENT (%) 00 75 60 40 0 0 40 60 80 00 5 OUTPUT OLTAGE (%) (Only for power supply system) RCP-600-48 RCP-600-4 RCP-600- RCB-600-48 RCB-600-4 RCB-600- OUTPUT OLTAGE(%) 60 48 9. 30 5 60 Non-Linear 4 48 9.6 7. 36 OUTPUT OLTAGE(%) 30 4 8 5 9 Non-Linear 0 0 0 0.4 4.7 5 0 0 0 0.4 4.7 5 For power supply system EXTERNAL OLTAGE (DC) For charger system EXTERNAL OLTAGE (DC) File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System 3. Output Current Programming (or, PC / remote current programming / dynamic current trim) The output current can be trimmed to 0~00% of the rated current by applying EXTERNAL OLTAGE. CN +S + - RHP-U System -S PC CN - Signal 5 4 LOAD EXTERNAL OLTAGE +S & +, -S & - also need to be connected on CN. (Only for power supply system) Iout Iout OUTPUT CURRENT (%) 0 00 Non-Linear OUTPUT CURRENT (%) 00 Non-Linear 0 0 0.4 4.7 5 EXTERNAL OLTAGE (DC) 0.4 4.7 5 EXTERNAL OLTAGE (DC) For power supply system For charger system 4. Remote ON-OFF Control The PSU can be turned ON/OFF together or separately by using the "Remote ON/OFF" function. 3 3 CN ON/OFF A 7 CN ON/OFF A 7 ON/OFF B ON/OFF B ON/OFF C ON/OFF C RHP-U System 5 ON/OFF D RHP-U System 5 9 ON/OFF D 9 ON/OFF E ON/OFF E +5-AUX +5-AUX Between ON/OFF and +5-AUX SW Open SW Short Output OFF ON 5.PMBus Communication Interface RCP-600/RCB-600 supports PMBus Rev.. with maximum 00KHz bus speed, allowing information reading, status monitoring, output trimming, etc. For details, please refer to the Function Manual. File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System Mechanical Specification Case No.4A Unit:mm 4 6 3 5 E D CN C 4 3 CN 6 5 B JK A RHP-UT FG 0 N 8. L FG 0 N 8. L FG 0 N 8. L FG 0 N 8. L FG 0 N 8. L 4-M8 L=6 8 8 E D CN C 4 3 CN 6 5 B JK A RHP-UI IEC30-C4 4-M8 L=6 IEC30-C4 IEC30-C4 IEC30-C4 IEC30-C4 440 5-M4 L=4 5-M4 L=4 9.5 5 9.5 SR SR SR SR SR 5.6 0.7.6 0.7 35 8.4 4 max. Air flow direction Module E Module D Module C Module B Module A 7 306 365 4 7.65 4 7.65 44 0. 9.5 466. 48.6 7.4 Mounting Instruction Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque M4 4mm 7~ 0Kgf-cm Mounting Surface Mounting Screw Chassis of RHP-U RACK L File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System LED Status Indicators & Corresponding Signal at Function Pins For power supply system LED Description Green The power supply functions normally. Red The LED will present a constant red light when the abnormal status (OTP, OLP, fan fail and charging timeout) arises. Red (Flashing) The LED will flash with the red light when the internal temperature reaches 60 ; under this condition, the unit still operates normally without entering OTP. ( In the meantime, an alarm signal will be sent out through the PMBus interface.) For charger system LED Description Green Float (stage 3) Orange Charging (stage or stage ) Red The LED will present a constant red light when the abnormal status (OTP, OLP, fan fail and charging timeout) arises. Red (Flashing) The LED will flash with the red light when the internal temperature reaches 60 ; under this condition, the unit still operates normally without entering OTP. ( In the meantime, an alarm signal will be sent out through the PMBus interface.) Connector Pin No. Assignment( CN) : HRS DF-6DP-DS 6 Mating Housing Terminal HRS DF-6DS or equivalent HRS DF-**SC or equivalent 5 Pin No. Function,5,9,3,7 AC-OK,6,0,4,8 DC-OK 3,7,,5,9 Remote ON-OFF 4,8,,6,0 T-ALARM +5-AUX 3 4 5 6 Description High (4.5 ~ 5.5) : When the input voltage is 87rms. Low (-0. ~ 0.5) : When the input voltage is 75rms. The maximum sourcing current is 0mA and only for output. (Note.) For power supply system High (4.5 ~ 5.5) : When the out 80% ± 5%. Low (-0. ~ 0.5) : When out 80% ± 5%. The maximum sourcing current is 0mA and only for output. (Note.) For charger system High (4.5 ~ 5.5) : When the out 8/6/3 ±. Low (-0. ~ 0.5) : When out 8/6/3 ±. The maximum sourcing current is 0mA and only for output. (Note.) DC OK is associated with battery low protection. The unit can turn the output ON/OFF by electrical signal or dry contact between Remote ON-OFF and +5-AUX. (Note.) Short (4.5 ~ 5.5) : Power ON ; Open (0 ~ 0.5) : Power OFF ; The maximum input voltage is 5.5. High (4.5 ~ 5.5) : When the internal temperature exceeds the limit of temperature alarm, or when fan fails. Low (-0. ~ 0.5) : When the internal temperature is normal, and when fan normally works. The maximum sourcing current is 0mA and only for output(note.) Auxiliary voltage output, 4.5~5.5, referenced to GND-AUX (pin ). The maximum load current is 0.3A. This output has the built-in "Oring diodes" and is not controlled by the remote ON/OFF control. GND-AUX +-AUX Auxiliary voltage output GND. The signal return is isolated from the output terminals (+ & -). Auxiliary voltage output, 0.8~3., referenced to GND-AUX (pin ). The maximum load current is 0.8A. This output has the built-in "Oring diodes" and is not controlled by the remote ON/OFF control. -(Signal) Negative output voltage. For local sense use only; It can't be connected directly to the load. PC Connection for output current programming. The current can be trimmed within its defined range. (Note.) P Connection for output voltage programming. The voltage can be trimmed within its defined range. (Note.) Note.: Non-isolated signal, referenced to [-(signal)]. Note.: Isolated signal, referenced to GND-AUX. Connector Pin No. Assignment( CN) : HRS DF-4DP-DS 4 3 Mating Housing Terminal HRS DF-4DS or equivalent HRS DF-**SC or equivalent For power supply system +S -S Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5. 3 4 +(Signal) -(Signal) Positive output voltage. For local sense use only, can't be connected directly to the load. Negative output voltage. For local sense use only, can't be connected directly to the load. For charger system RTH+ RTH- 3,4 NC Temperature sense associated with the temperature compensation funcion. Not use. File Name:RHP-U RACK SYSTEM-SPEC 06--09
600~8000W U Distributed Power/Charger System RHP-U Rack System Connector Pin No. Assignment( JK) : RJ45 8 positions 8 8 Pin No., 3 4 5 6 Function Description DA,DB Differential digital signal for parallel control. (Note.) Negative output voltage signal. -(signal) It is for local sense and certain function reference; it cannot be connected directly to the load. CONTROL Remote ON-OFF control pin used in the PMBus interface. (Note.) NC Retain for future use. SDA Serial Data used in the PMBus interface. (Note.) 7 SCL Serial Clock used in the PMBus interface. (Note.) 8 GND-AUX Auxiliary voltage output GND. The signal return is isolated from the output terminals (+ & -). Note.: Non-isolated signal, referenced to [-(signal)]. Note.: Isolated signal, referenced to GND-AUX. File Name:RHP-U RACK SYSTEM-SPEC 06--09