ata sheet Sight glass (ow pressure) s SG, SGI, SGN, SGR, SGRI and SGRN SG is sight glasses for low pressure application (Max Working Pressure 500 psig). SG is available with flare, solder and socket connections, and with and without moisture indicators. SG and SGR, without moisture indicator, are mainly used to indicate the condition of the refrigerant in the liquid line or the flow in the oil return line from the oil separator. SGI / SGN and SGRI / SGRN are equipped with sensitive indicators that reflects a changes colour, depending on the moisture content in the refrigerant. Features Provides fast and easy indication of: igh system moisture content ack of subcooling or low system charge iquid level in receiver (vessel mount versions only) Oil level in compressor (vessel mount versions only) Two Indicator types: I provides optimal moisture indication for CFC refrigerants with mineral oil, e.g. R22 N provides optimal moisture indication for all CFC and Non-flammable FC refrigerants All indicators are dirt resistant Available in both inline and vessel mount versions ermetically sealed, tempered glass for easy viewing Available in flare / flare, solder / solder connection or socket type anfoss CS (ws) 206.0 KRCC.P.EK0.B3.22 5200673
ata sheet Sight Glass, s SG, SGI, SGN, SGR, SGRI and SGRN Approvals Technical data Refrigerants CFC / Non- flammable FC Media temperature -58 75 F Maximum working pressure PS / MWP = 500 psig Selection Note: when storing, transporting or installing the Sight Glass, avoid the chemical indicator to get in contact with non-refrigerant medium or fluid (like water, oil, ect.) Prior to selecting a sightglass with moisture indicator, the following should be considered: of refrigerant Water solubility of refrigerant The level at which a danger signal is required to prevent the formation of harmful acids The following tables indicate moisture content levels at which the sightglass indicator will register a dry or wet system for various refrigerants. The values under green / dry are to be taken as the maximum permissible moisture content for the system. When the green color begins to fade indicating an increase in moisture levels, the sightglass should be checked more frequently. If the moisture levels increase enough to change the indicator to yellow indicating a wet system, the filter drier must be changed immediately. Note: for colours reflecting moisture values of other refrigerants, please contact anfoss psi = 0.07 bar 5/9 (t F - 32) = t2 C Refrigerant R22 R34a R404A R407C R507 ) The values refer to liquid temperature Green / dry Moisture content ppm = parts per million 77 F ) 0 F ) Intermed. color Yellow / wet Green / dry Intermed. color Yellow / wet SGI < 50 50 300 > 300 < 250 250 500 > 500 SGN (recommended) < 30 30 20 > 20 < 50 50 200 > 200 SGI < 30 30 270 > 270 < 20 20 430 > 430 SGN (recommended) < 30 30 00 > 00 < 45 45 70 > 70 SGI < 90 90 70 > 70 < 25 25 250 > 250 SGN (recommended) < 20 20 70 > 70 < 25 25 00 > 00 SGI < 70 70 350 > 350 < 280 280 560 > 560 SGN (recommended) < 30 30 40 > 40 < 60 60 225 > 225 SGI < 80 80 60 > 60 < 40 40 280 > 280 SGN (recommended) < 5 5 60 > 60 < 30 30 0 > 0 anfoss CS (ws) 206.0 KRCC.P.EK0.B3.22 5200673 2
ata sheet Sight Glass, s SG, SGI, SGN, SGR, SGRI and SGRN Ordering SG without indicator Valve type type SG 22s Solder OF x OF 7 8 04-207 SGR NPT 2 04-0002 SGI with I type indicator Valve type type SGI 6 4 04-0063 Flare int. x ext. ) SGI 0 3 8 04-0064 SGI 6s Solder OF x OF 4 04-0066 SGI 0s Solder OF x OF 3 8 04-0067 SGI 2s Solder OF x OF 2 04-0068 SGI 6s Solder OF x OF 5 8 04-0069 SGI 22s Solder OF x OF 7 8 04-0070 SGRI NPT 2 04-03 ) Can be screwed directly onto the anfoss filter drier Note: for other connection SG codes, please contact anfoss manufacture factory in. = 25.4 mm SGN with N type indicator Valve type type SGN 6 4 04-032 Flare int. x ext. SGN 0 3 8 04-033 SGN 6 4 04-037 SGN 0 Flare int. x ext. ) 3 8 04-038 SGN 2 2 04-039 SGN 6s 4 04-042 SGN 0s 3 8 04-043 SGN 2s Solder OF x OF 2 04-044 SGN 6s 5 8 04-045 SGN 22s 7 8 04-047 SGN 6s 4 04-05 Solder OF x OM SGN 2s 5 6 04-055 SGRN NPT 2 04-0006 ) Can be screwed directly onto the anfoss filter drier anfoss CS (ws) 206.0 KRCC.P.EK0.B3.22 5200673 3
ata sheet Sight Glass, s SG, SGI, SGN, SGR, SGRI and SGRN imensions and weights SGI, SGN flare, int. ext. SGI, SGN flare, ext. ext. B B SGI, SGN solder OF OF SGI, SGN solder OF OM B B in. = 25.4 mm lb = 0.454 kg type B ø Net weight [lbs.] SGI / SGN 6 Flare 2.638 0.945 0.55 0.55.063 0.22 SGI / SGN 0 ext. ext. 3.228.02 0.630 0.748.260 0.44 SGI / SGN 6.8 0.945 0.55 0.630.063 0.22 SGI / SGN 0 Flare int. ext 2.244.8 0.669 0.866.260.260 SGI / SGN 2 2.323.8.8 0.945.260 0.66 SGI / SGN 6s 3.976 0.276 0.945 0.55 0.55.063 0.22 SGI / SGN 0s 4.685 0.354 0.945 0.55 0.55.063 0.22 SGI / SGN 2s OF OF solder 5.748 0.394.02 0.630 0.748.063 0.44 SGI / SGN 6s 5.748 0.472.8 0.709 0.866.063 0.44 SGI / SGN 22s 6.8 0.699.457 0.827.063.260 0.66 SGI / SGN 6s OF OM 3.976 0.276 0.945 0.55 0.55.063 0.22 SGI / SGN 2s solder 5.748 0.394.02 0.630 0.748.063 0.44 anfoss CS (ws) 206.0 KRCC.P.EK0.B3.22 5200673 4
imensions and weights (continued) SG socket B in. = 25.4 mm lb = 0.454 kg type B ø Net weight [lbs.] SGR 2 NPT.8 0.709.063 0.22 SGRI / SGRN 2 NPT.8 0.709.063 0.22 anfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. anfoss reserves the right to alter its products without notice. This also applies to product already on order provided that such alterations can be made without subsequential changes being necessary eady agreed. All trademarks in this material are property of the respective companies. anfoss and the anfoss logotype are trademarks of anfoss A/S. All rights reserved. anfoss CS (ws) 206.0 KRCC.P.EK0.B3.22 5200673 5