.56" Quadruple Digit Numeric Displays Technical Data Sheet Model No.: KW4-56NXLB-P Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 1 OF 6
Features:.56 (inch) digit height. Excellent segment uniformity. Sold state reliability. Industrial standard size. Low power consumption. The product itself will remain within RoHS compliant Version. Descriptions: The KW4-56NXXX series is a lager 14.2 mm (.56 ) high seven segments display designed for viewing distances up to 7 meters. These displays provide excellent reliability in bright ambient light. These devices are made with White segments and black surface Applications: Audio equipment. Instrument panels. Digital read out display. Device Selection Guide: Model No. Chip Material Source Color Description KW4-56NALB-P Hyper Red Common Anode AlGaInP KW4-56NCLB-P Hyper Red Common Cathode Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 2 OF 6
12 ++D6+PIN Luckylight Package Dimension: 8.1 [.319] +PIN 7 8 1.35 [.53] 8 [.315] 14.2 [.56''] 19 [.749] 15.24 [.6] PIN 1 12.7*3=38.1 [1.51] PIN 6 6.3 [.248]±.5 5.2[1.978] DIG.1 DIG.2 DIG.3 DIG.4 A F G B D5 Φ.5 [.2] E C 2.54*6=15.24 [.6] D DP KW4-56NALB-P 14 DIG.1 11 DIG.2 7 DIG.3 6 DIG.4 A B C D E F G DP A B C D E F G DP D5 D6 A B C D E F G DP A B C D E F G DP 13 9 4 2 1 12 5 3 8 KW4-56NCLB-P 14 DIG.1 11 DIG.2 7 DIG.3 6 DIG.4 A B C D E F G DP A B C D E F G DP D5 D6 A B C D E F G DP A B C D E F G DP 13 9 4 2 1 12 5 3 8 Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±.25 mm (. ) unless otherwise noted.. 3. Specifications are subject to change without notice. Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 3 OF 6
Absolute Maximum Ratings at Ta=25 Parameters Symbol Max. Unit Power Dissipation (Per Segment) PD 65 mw Peak Forward Current (Per Segment) (1/ Duty Cycle,.1ms Pulse Width) IFP ma Forward Current (Per Segment) IF 25 ma Dating Linear From 25.4 ma/ Reverse Voltage VR 5 V Operating Temperature Range Topr -4 to +8 Storage Temperature Range Tstg -4 to +85 Soldering Temperature Tsld 26 for 5 Seconds Electrical Optical Characteristics at Ta=25 Parameters Symbol Min. Typ. Max. Unit Test Condition Luminous Intensity IV 9. 18. --- mcd IF=2mA (Note 1) Luminous Intensity Matching Ratio (Segment To Segment) Iv-m --- --- 2:1 IF=mA Peak Emission Wavelength λp --- 645 --- nm IF=2mA Dominant Wavelength λd --- 63 --- nm IF=2mA (Note 2) Spectral Line Half-Width λ --- 2 --- nm IF=2mA Forward Voltage VF --- 2. 2.6 V IF=2mA Reverse Current IR --- --- 5 µa VR=5V Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 4 OF 6
Typical Electrical / Optical Characteristics Curves (25 Ambient Temperature Unless Otherwise Noted) Relative Luminous Intensity (%) Spectrum Distribution Ta=25 75 5 25 3 4 5 6 7 8 Wavelength λp (nm) Forward Current IF (ma) Forward Current & Forward Voltage 8 6 4 2 Ta=25 1.4 1.6 1.8 2. 2.2 2.4 2.6 Forward Voltage VF (V) Relative Luminous Intensity (%) Luminous Intensity & Ambient Temperature 1-6 -4-2 2 4 6 8 Ambient Temperature Ta ( ) Luminous Intensity & Forward Current Relative Luminous Intensity (%) 1 Ta=25 f=1khz Duty=1/ 1 2 3 Forward Current IF (ma) Forward Current IF (ma) Forward Current Derating Curve 5 4 3 25 2 2 4 6 8 Ambient Temperature Ta ( ) Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 5 OF 6
Please read the following notes before using the datasheets: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 If the package contains a moisture proof bag inside, please don't open the package before using. 2.2 Before opening the package, the LEDs should be kept at 3 or less and 8%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 3 or less and 6%RH or less. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 26 for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Soldering When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance from the base of the lens to the soldering point. To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Temperature Soldering Time Soldering Iron 3 Max. 3sec.Max. (one time only) Pre-heat Pre-heat Time Solder Wave Soldering Time Wave Soldering Max. 6 sec. Max. 26 Max. 5sec.Max. Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic failure of the LED. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Spec No.:W5643E/F Rev No.: V.2 Date: Oct/23/26 Page: 6 OF 6