S14 / S15 ASSEMBLY INSTRUCTIONS Assembly tools required : Hammer, Phillips #, #3 and regular screwdriver, 10 and 17mm wrenches Special Notes : To make the assembly simple and well done, you have to be familiar with the parts. Follow the step-by-step instructions on a clean area ( ex. carpet). Read instructions before starting the asembly 1- Bed side left/right - Upper/lower bed rail 3- External doors 4- Middle doors 5- Cabinet side left/right 6- Cabinet top 7- Cabinet cross rails 8- Bed wide bottom panel (S14, 4X; S15, 5X) 9- Bed narrow bottom panel (S14 only) 6 Parts not shown : 5-1 10- Cabinet upper rail 11- Bed side rail, plywood 1- Crossing rail, plywood 13- Bed rail upper/lower 31- Door reinforcement rails 8 7 5-1-1 9 3 4 1- S14 : 54 inches bed S15 : 60 inches bed Page 1
S14 / S15 Pre-Assembly check list Hardware pack Item : 14 Item : 15 Item : 16 Item : 17 Item : 18 3 3 48 1 40 15mm Eccentric housing Quick-Fit dowel Assembly screw Screw #8-1 1/8" Screw #6-5/8" Item : 19 Item : 0 Item : 1 Item : Item : 3 Item : 4 4 8 8 0 4 16 mm 7/8" Handle Screw ( round head ) Bolt M6-19 mm Screw #8-1" Screw #10-3/4" Wood dowel Item : 5 1 Item : 6 40 Item : 7 3 Item : 8 Screw cap Screw #8-1/ " reinforcement plate Item : 30 Seafty chain divice Bed feet Item : 9 Mechanism for Collapsible bed, left side shown Part b This item as a left an a right part Page Part a
Item: 15 X 5-1 S14 / S15 Wall cabinet Step 1 : Left side shown Mecanism preparation : 1a: Remove lock pin a 1b: Open mecanism b Item: 18, 11X Item 9a Item: 14, 4X from top side Step : Repeat step 1 right side without safety chain Secure two assembly screws on the top no screw cap. Step 3 5-1 Edgeband both side 10 6 Item: 16 18X Assembly screw 18 places typ. 7 7-1 7 Edgeband one side 5- Page 3 Item: 6 16X Screw cap
S14 / S15 Wall cabinet Step 4 Wall 4a. Remove bottom wall trim to install cabinet against wall 4b. Place level tool on the cabinet side and adjust if needed. 7 X 4c. Locate vertical studs in the wall, secure upper end of cabinet with a minimum of two #8 X 1/" screws in upper trim ( 3 screws included). Use proper screws depending wall construction. Remove wall trim to fit in cabinet Warning : It is mandatory to fix the cabinet firmly to the wall by locating inwall studs. Severe damage to the cabinet and possible injuries to people may result. Use longer or bigger screws if needed. Stellar Home Furniture is not responsible for part damages or injuries caused by inappropriate installation. Page 4
Step 5 Item: 4 16X Insert dowels completely to the bottom of holes to avoid doors damage S14 / S15 Bed, base 1-1 1- Step 6 Locate and secur front/ rear panel using eccentric housing. Make sure to align doors and front/ rear panels before final tight. 3 Item: 15 8X 4 4 Item: 14 16X 3 Note carefully handle holes position Insert eccentric housing then tighten clockwise with screwdriver. Page 5
S14 / S15 Bed base Slide down sides 1-1 and 1- first, then secure with eccentric housing. Place and tighten assembly screw. Step 7 1-1 1- Item: 14, 1X Step 8 Item: 16 8X Item: 6 8X Secure reinforcement plate, locate it inside, than align with M6 bolt, 4 places. Make sure to tighten bolt using 10 mm wrench. Repeat on the other side. Item: 9b X Item: 30 X DETAIL C SCALE 1 : 6 Item: 1, 8X Item: 18 6X DETAIL A SCALE 1 : 8 Do not loosen up the bolt on the rear side of the mechanism. Page 6
S14 / S15 Bed base Step 9 Inner frame assembly 1 11-1 11- Item: 16, 8X Step 10 Item: 13 X *Note holes orientation Item: 6 11X Item: 16, 14X Secure upper & lower rails #13 first, than bring down inner frame from step 9 and secure it using assembly screw. Page 7
Step 11 Note: With two people, one on each side, insert bed into cabinet by holding it verticaly and paralell to the cabinet. Make sure to align mecanism on each side as shown below. Insert part A top flat in between part B opening as shown. a b Do not loosen up the bolt on the rear side of the mechanism. Warning! Do not open bed completely until safety scews are installed. It may result in severe damages to the cabinet and bed parts as well as possible injury to people. Step 1 Open bed just enough to access mecanism and insert safety scews. Item: 3, 4X Safety screws, two on each side. DÉTAIL H ECHELLE 1 : 8 Page 8
Wall Bed Step 13 S14 / S15 9a: Once bed is installed into wall cabinet, move sideway cabinet bottom until a perfect alignement of doors with wall cabinet. Align cabinet with doors 9b: Then secure cabinet bottom with minimum one screw into lower trim. Make sure to reach wall stud. Wall move cabinet sideway Bed Lower cabinet trim 7 Step 14 Cut to size the bottom wall trim previously removed at step 4 and re-install it both sides of cabinet. Page 9 Bottom wall trim cut to size
Step 15 S14 / S15 Mur / Wall Item: 17 1X Be sure you use the right screw to avoid door damages Do not overtight Item: 31 X Step 16 Wall Item: 5 Item: 18 X Item: 0 8X D DÉTAIL V ECHELLE 1 : 10 Can be mounted left or right side (use pilot holes) Item: 0X DETAIL D DETAIL 1 : 10 Item: 19 4X Handle and screws, 4 places Item: 18 4X DETAIL E SCALE 1 : 6 Page 10 Can be mounted left or right side (use pilot holes)
S14 / S15 Step 17 Balance adjustement : For a perfect balance of mechanism, you may have to adjust it as required since not all mattresses have the same weight. Use a 17mm (or 11/16'') wrench. Do it slowly half turn at a time, equally both sides. To obtain a perfect balance, the bed must be stationary in each opened position. Do not unscrew completely the adjustement bolt DÉTAIL F ECHELLE 1 : 5 F Page 11
Warranty The warranty from Cyme Tech covers defects in material and workmanship for a period of 5 years from the date of purchase. The original purchase receipt is required as proof of purchase. This warranty is limited to the replacement of defective parts. This warranty does not cover normal wear and tear, scratches, alterations and intentional and non-intentional damages. This warranty does not cover the product if it has been placed outdoors or in a humid environment. This warranty is only valid for purchases made at an authorized Cyme Tech dealer in Canada and in the United States. This warranty defines the limits of Cyme Tech s liability and entitles the original buyer to specific rights. Any warranty defined by law in your state or province is limited to a period of 5 years. If the law in your state or province prohibits this restriction, then it does not apply. Page 1