Xitanium 40W 0.2-0.7A LS 12-24V DC input off-grid constant-current LED driver Philips Xitanium DC input off-grid drivers are specifically designed to deliver high performance and configurability in battery-powered off-grid applications. The portfolio offers both a central and a standalone dimming protocol, further increasing the energy savings and CO 2 reductions achieved with LED lighting. The Xitanium technology ensures maximum robustness combined with a very long lifetime. Benefits Features Applications Ultimate robustness, offering peace of mind and lower Long lifetime and high application robustness Residential areas maintenance costs Adjustable Output Current (AOC) City centres Easy to design-in, configure and install for insulation Class PWM interface for external dimming Street lighting III applications Single-step autonomous dimming via configurable LumiStep Parks Energy savings through high efficiency and via multiple Thermal protection for the LED module (MTP) Small stadiums dimming options Configurable via HyperTerminal Security lighting Suitable for use with standard 12 and 24V batteries Protection against deep discharge of batteries July 2015
Electrical input data Rated input voltage range V bat 12... 24 Vdc Performance range Rated input voltage range V bat 10.5... 32 Vdc Operational range Input undervoltage lockout V bat 9.5 Vdc Restart at 10.5Vdc Rated input current range 0.37... 3.62 Adc @ output power range @ rated input voltage range Max. input current 4.4 Adc @ rated output power @ minimum performance input voltage Inrush peak current and width 30/20 A p/µs @ 24Vdc, 50% pulse time width Rated input power 50 W @ rated output power @ rated input voltage Driver efficiency 90 % @ rated output power @ rated input voltage Input-output insulation None Electrical output data Regulation method Constant Current Output voltage 40... 100 Vdc V bat = 24Vdc 25... 100 Vdc V bat = 12Vdc Output voltage max. 110 V Peak voltage at open load Output current 250/300/350/450/480/500/515/600/650/700 ma See important remark at page 5 Output current tolerance ± 5 % Output current ripple HF 150 mapp 100... 150kHz range Output power range 8... 40 W Electrical data controls input Control method LumiStep Output current amplitude dimming External PWM V control = 3.3... 5.0V, f = 250Hz. Response time: 2s Dimming range 10...100% % Galvanic insulation None Logistical data Specification item Value Product name Xitanium 40W 0.2-0.7A LS 12-24V Order code EOC 872790092559300 Logistic code 12NC 9290 006 11903 Pieces per box 6 Wiring & Connections Battery input wire cross-section 0.5... 2.5 mm 2 WAGO 804, solid / stranded wire; 1.5 mm 2 recommended 22...12 AWG Input wire strip length 10... 11 mm PWM control input wire cross-section 0.5...1.5 mm 2 WAGO 250, solid / stranded wire 22... 14 AWG Input wire strip length 8.5... 9.5 mm Programming interface 3.5mm mini jack Cable type FTDI TTL-232R-3V3-AJ TTL-USB Output connection JST - Maximum NTC output cable length 0.6 m Connector type: JST BM07B-PASS-TFT (LF)(SN) Connector counterpart Housing: PAP-7-V-S Connector counterpart Contacts: SPHD-002T-P0.5
Insulation Insulation Inputs Chassis LED NTC RSET Inputs Basic None None None Chassis Basic Basic Basic Basic LED None Basic None None NTC None Basic None None RSET None Basic None None Dimensions and weight Length (A1) 149.6 mm Width (B1) 90 mm Height (C1) 36.8 mm Fixing hole diameter (D1) 4.5 mm Mounting screw: M4 Fixing hole distance (A2) 134 mm Fixing hole distance (B2) 70 Weight 191 gram
Operational temperatures and humidity Driver ambient operational temperature -20...+65 o C At rated output power. Higher ambient temperature allowed as long as Tcase-max is not exceeded. Tcase-max 85 o C Maximum temperature measured at Tcase-point Tcase-life 75 o C Measured at Tcase-point Maximum housing temperature 120 o C In case of failure Relative humidity 10... 90 % Non-condensing Ingress Protection 20 Storage temperature and humidity Ambient temperature -40...+85 o C Relative humidity 5... 95 % Non-condensing Lifetime Driver lifetime 50,000 hours Tcase Tcase-life. See graph. Maximum failures = 10% Features Specification item Programmable Remark Default setting LumiStep Yes Single-step, light turn-off possible Disabled Adjustable Output Current (AOC) No Discrete steps possible, see page 2 and 5 700mA (open RSET interface) Module Temperature Protection (MTP) No NTC type: Vishay 15kOhm p/n NTCS0805E3153GMT Permanently enabled. Threshold value: 2536 Ohm Features Specification item Value Remark Condition Reversed input polarity protection Yes Open load protection Yes Automatic recovering Short circuit protection Yes Automatic recovering Over power protection Yes Output will shut down, no recovery Overheating protection Yes Hot wiring No Suitable for luminaire insulation class III Per IEC60598
Certificates and standards Specification item Approval marks Value CE / ENEC / UL / CSA Surge immunity Surge immunity (comm. mode) 0.5 kv Input/output - chassis Graphs Operating window & dimming Important design-in and application notes: 1: This driver can only be set at following discrete output currents with corresponding RSET values as shown below. The use of inbetween resistance values may lead to instable driver operation and is not recommended. The RSET resistor must be connected to driver terminals RSET and RSET/RNTC COMM. Required power rating of this resistor is 0.125... 0.25W. Maximim distance between RSET resistor and driver is 0.6m. RSET (k-ohm) Output current (ma) 0.27 250 0.56 300 0.91 350 2.2 450 2.7 480 3.3 500 3.6 515 8.2 600 18 650 infinite (open) 700 2: The prescribed NTC must be connected to driver terminals RNTC and RSET/RNTC COMM. A 15 kilo-ohm fixed-value dummy resistor with 0.125... 0.25W power rating may be used as substitute if MTP functionality is not required. If the RNTC interface is left open then the driver will not start up. Maximim distance between the NTC and driver is 0.6m. 3: The forward voltage of the connected LED module must remain within the specified operating window limits under all operating conditions. Otherwise, the driver will shut down. 4: It is not allowed to combine the RSET/RNTC COMM connection with the LED output minus connection. 5: Please refer to Appendix B of the Philips Fortimo LED LLM Design-in guide for further driver configuration details. Philips MultiOne software does not support configuration of this driver. 6: The following output cable is required for driver output connection and available from Philips: Description: Cable Fortimo solar 7pin to 7pin 12NC: 9290 008 38003 EOC: 871829125424900 2017 Philips Lighting Holding B.V. All rights reserved. This document contains information relating to the Philips Lighting portfolio, intended for companies who may be interested in developing their product offering. Note that the information provided is subject to change. Philips Lighting does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. Date of release: October 2017 www.philips.com/technology