Bauart gepruft Sicherheit egelma ge od o s be wac g 1W Constant Voltage Constant Current LED Driver IP65 IP67 www. tuv.com ID 00000000 Ⅰ A E
SPECIFICATION MODEL HBG124 HBG136 HBG148 HBG1 DC VOLTAGE 24V 36V 48V V CONSTANT CURRENT REGION Note.2 14.4 ~ 24V 21.6 ~ 36V 28.8 ~ 48V 36 ~ V RATED CURRENT 6.5A 4.4A 3.3A 2.6A RATED POWER Note.5 156W 158.4W 158.4W 156W RIPPLE & NOISE (max.) Note.3 0mVpp 300mVpp 300mVpp 300mVpp OUTPUT CURRENT ADJ. RANGE Adjustable for AType (via builtin potentiometer) 3.9 ~ 6.5A 2.6 ~ 4.4A 1.98 ~ 3.3A 1.6 ~ 2.6A VOLTAGE TOLERANCE Note.4 ±2.0% LINE REGULATION ±0.5% LOAD REGULATION ±1.0% SETUP, RISE TIME Note.6 2500ms, 0ms / 115VAC 500ms, 0ms / 230VAC HOLD UP TIME (Typ.) 12ms /115VAC, 230VAC INPUT PROTECTION OTHERS NOTE VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE SAFETY STANDARDS Note.5 WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC TOTAL HARMONIC DISTORTION SHORT CIRCUIT WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note. 8 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load %/115VC,230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) COLD START 65A(twidth=425μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 4 units (circuit breaker of type B) / 7 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 28 ~ 34V 41 ~ 47V 54 ~ 62V 65 ~ 75V Shut down o/p voltage with autorecovery or repower on to recovery Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase=40 ~ 85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. 92% 92% 93% 93.5% 1.7A / 115VAC 0.78A / 230VAC 0.7A / 277VAC Tcase=85 ~ 95% RH noncondensing 40 ~, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750 (type HL ),CSA C22.2 No.250.1312, TUV EN613471,EN61347213;IP65 or IP67 approved, design refer to TUV EN950 I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:0.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6032 Class C (@load %) ; EN6033 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547,light industry level ( surge immunity:lineearth:4kv,lineline:2kv) MTBF 783.1K hrs min. Telcordia SR332 (Bellcore) ; 252.3Khrs min. MILHDBK217F (25 ) DIMENSION ψ151.68mm *66.5mm (D * H) PACKING 1.53Kg; 8pcs/13.8Kg/1.61CUFT
BLOCK DIAGRAM fosc : KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.C.P. V V FG O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (min.) (A) Constant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)
DIMMING OPERATION DIM(Blue) DIM(White) V(Red) V(Black) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC % 90% V V DIM DIM Additive Voltage Output current (%) % 70% % 50% 40% 30% % DO NOT connect "DIM to V" 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Applying additive resistance: Output current (%) % 90% % 70% % 50% 40% 30% % 10% 10% % 30% 40% 50% % 70% % 90% % Duty cycle of additive 10V PWM signal dimming input V % 90% V DIM DIM DO NOT connect "DIM to V" Additive Resistance Output current (%) % 70% % 50% 40% 30% % 10% 10K/N K/N 30K/N 40K/N 50K/N K/N 70K/N K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HBG1CSPEC 1616
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HBG1 BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE LOAD (%) 50 40 230VAC Input only LOAD (%) 40 230VAC Input only 40 30 10 0 15 30 50 70 (HORIZONTAL) 40 30 0 10 30 50 70 85 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 LOAD (%) 90 70 50 40 90 125 135 145 155 165 175 1 0 230 305 INPUT VOLTAGE (V) Hz Derating is needed under low input voltage. PF 1 0.98 0.96 0.94 0.92 0.9 0.88 0.86 0.84 0.82 0.8 0.78 Constant Current Mode 50% % 70% % 90% % (1W) LOAD 277V 230V 115V TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 75 EFFICIENCY vs LOAD possess superior working efficiency that up to 93% can be reached in field applications. 48V Model, Tcase at 75 THD 25% % 15% 10% 5% 0% 50% % 70% % 90% % LOAD 277VAC 230VAC 115VAC EFFICIENCY(%) 94 92 90 88 86 84 82 78 76 74 10% % 30% 40% 50% % 70% % 90% % LOAD 277V 230V 115V
LIFE TIME 1 LIFETIME(Kh) 40 0 25 35 45 55 65 75 85 Tc a s e ( )
MECHANICAL SPECIFICATION Case No.211 Unit:mm BlankType ψ151.68 tc 66.5 52.5 8.2 14.5 M10*P1.518h 300± SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) 4ψ6.0 45 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point Ta AType ψ151.68 tc 66.5 52.5 8.2 14.5 M10*P1.518h 0± 300± SJTW 18AWG*3C SJTW 18AWG*2C V(Red) V(Black) 13.00 13.33 4ψ6.0 45 Ta tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point BType ψ151.68 tc 66.5 52.5 8.2 14.5 M10*P1.518h DIM(Blue) DIM(White) 300± SVT 18AWG*2C 300± SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) 4ψ6.0 45 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point Ta
EType 66.5 52.5 ψ151.68 tc 8.2 14.5 M10*P1.518h 300± SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) 4ψ6.0 45 Ta 1 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point INSTALLATIONS Hanger Chain Spot Light High Bay Light Stage Light Caution Please inspect the appearance of the driver if the package is damaged. There should not be any cracks. Please do not drop or bump the driver. All screws including the suspension screw should be paired with a spring washer and locked tight. The entire luminaire, including the driver, should be limited to 10Kg or less. The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation. Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.