IP65 IP67 ~ A Dx File Name:ELG150SPEC 1603
SPECIFICATION SAFETY & EMC OTHERS NOTE EMC EMISSION 150W Constant Voltage Constant Current LED Driver Compliance to EN55015,EN6100032 Class C ( load) ; EN6100033 MODEL ELG15012 ELG15024 ELG15036 ELG15042 ELG15048 ELG15054 DC VOLTAGE 12V 24V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.2 6 ~ 12V 12 ~ 24V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT 10A 6.25A 4.17A 3.57A 3.13A 2.8A RATED POWER 1W 150W 150.1W 150W 150.2W 151.2W RIPPLE & NOISE (max.) Note.3 150mVpp 0mVpp 250mVpp 250mVpp 250mVpp 350mVpp VOLTAGE ADJ. RANGE Adjustable for AType only (via the builtin potentiometer) 10.8 ~ 13.2V 21.6 ~ 26.4V 32.4 ~ 39.6V 37.8 ~ 46.2V 43.2 ~ 52.8V 49 ~ 58V OUTPUT Adjustable for AType only (via the builtin potentiometer) CURRENT ADJ. RANGE 5 ~ 10A 3.2 ~ 6.25A 2.1 ~ 4.17A 1.8 ~ 3.57A 1.56 ~ 3.13A 1.4 ~ 2.8A VOLTAGE TOLERANCE Note.4 ±3.0% ±3.0% ±2.5% ±2.5% ±2.0% ±2.0% LINE REGULATION LOAD REGULATION ±2.0% ±1.0% ±1.0% SETUP, RISE TIME Note.6 500ms, 100ms/230VAC HOLD UP TIME (Typ.) 10ms/230VAC VOLTAGE RANGE Note.5 180 ~ 295VAC 254 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR 47 ~ 63Hz PF 0.95/230VAC or PF 0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< %@ load/230vac, or @ 75%load/277VAC (Please refer to TOTAL HARMONIC DISTORTION section) INPUT EFFICIENCY (Typ.) AC CURRENT 88% 0.9A / 230VAC 89% 0.7A/277VAC 90% 90% 90% 91% INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 65A(twidth=550μ s measured at Ipeak) at 230VAC; Per NEMA 410 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC <0.5W OVER CURRENT 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed PROTECTION 14 ~ 18V 28 ~ 34V 41 ~ 48V 47 ~ 54V 54 ~ 62V 59 ~ 68V OVER VOLTAGE Shut down output voltage, repower on to recover OVER TEMPERATURE Shut down output voltage, repower on to recover WORKING TEMP. Tcase=40 ~ 90 (Refer to "Derating Curve") MAX. CASE TEMP. Tcase=90 WORKING HUMIDITY ~ 95% RH noncondensing ENVIRONMENT STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 60 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750 (type HL ); CSA C22.2 No. 250.1312; ENEC EN613471, EN61347213 independent, EN62384; IP65 or IP67 approved WITHSTAND VOLTAGE ISOLATION RESISTANCE I/PO/P:3.75KVAC I/PFG:2.0KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH EMC IMMUNITY Compliance to EN6100042,3,4,5,6,8,11; EN61547, light industry level ( surge immunity LineEarth 6KV, LineLine 4KV) MTBF 313.66Khrs min. MILHDBK217F (25 ) DIMENSION 219* 63*35.5mm (L*W*H) PACKING 0.88Kg ; 16pcs/15.4kg/0.77CUFT File Name:ELG150SPEC 1603
Block Diagram PFC fosc : 50~1KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. V V O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. CASE GROUND DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) 50 (min.) (A) Constant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io(%) Typical output current normalized by rated current (%) This characteristic applies to Blank/A/B/DX/D2Type, For DAType, the Constant Current area is 70%~100% Vo. File Name:ELG150SPEC 1603
DIMMING OPERATION AC/N(Blue) AC/L(Brown) ELG150 DIM(Blue)* DIM(White)** V(Black) V(Red) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 0 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage LED Strips Output current (%) 100% 90% 80% 70% 60% 40% 30% % 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage * DIM for BType DA for DAType PROG for D2Type * *DIM for BType DA for DAType PROG for D2Type Output current (%) 100% 90% 80% 70% 60% 40% 30% % 10% 0% 0% 10% % 30% 40% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: 100% DIM Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): LED Strips V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" LED Strips V V DIM Additive Resistance DIM DO NOT connect "DIM to V" 90% 80% 70% 60% 40% 30% % 10% 0% Short 10K K 30K 40K 50K 60K 70K 80K 90K 100K Dimming input: Additive resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Output current (%) File Name:ELG150CSPEC 1603
DALI Interface (primary side; for DAType) Apply DALI signal between DA and DA. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output. Smart timer dimming function (for DxxType by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details. Ex : D01Type: the profile recommended for residential lighting Set up for D01Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 T2 06:00 07:00 100% 70% T3 11:00 T4 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a residential lighting application adopts D01Type, when turning on the power supply at 6:00pm, for instance: [1] The power supply will swih to the constant current level at 100% starting from 6:00pm. [2] The power supply will swih to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will swih to the constant current level at in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 8:00am, which is 14:00 after the power supply turns on. Ex: D02Type: the profile recommended for street lighting Set up for D02Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 01:00 T2 03:00 80% T3 T4 T5 8:00 11:00 100% 60% 80% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a street lighting application adopts D02Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will swih to the constant current level at starting from 5:00pm. [2] The power supply will swih to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will swih to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will swih to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on. File Name:ELG150CSPEC 1603
Ex: D03Type: the profile recommended for tunnel lighting Set up for D03Type in Smart timer dimming software program: Dimming Level(%) T1 T2 T3 TIME** 01:30 11:00 LEVEL** 70% 100% 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a tunnel lighting application adopts D03Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will swih to the constant current level at 70% starting from 4:30pm. [2] The power supply will swih to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on. File Name:ELG150CSPEC 1603
OUTPUT LOAD vs TEMPERATURE 100 100 80 80 60 60 LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 60 70 (HORIZONTAL) 40 0 10 30 50 70 85 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 100 90 80 Tcase at 80 1 0.98 0.96 Constant Current Mode LOAD (%) 70 60 50 40 PF 0.94 0.92 0.9 0.88 277V 230V 180 190 0 210 2 230 240 250 260 270 280 295 INPUT VOLTAGE (V) 60Hz Derating is needed under low input voltage. 0.86 60% 70% 80% 90% 100% (150W) LOAD TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 54V Model, Tcase at 80 54V Model, Tcase at 80 THD 12% 10% 8% 6% 4% 2% 0% 60% 70% 80% 90% 100% 277VAC 230VAC EFFICIENCY(%) 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 277V 230V LOAD 10% % 30% 40% 60% 70% 80% 90% 100% LOAD File Name:ELG150SPEC 1603
Mechanical Specification BlankType CASE NO.: 237A Unit:mm 300± 219 8 195 300± AC/N(Blue) AC/L(Brown) 63 SJTW 18AWGx2C 45.8 105 V(Black) V(Red) 12V,24V:SJTW 14AWGx2C 36V,42V,48V,54V:SJTW 18AWGx2C 4ψ4.5 : Max. Case Temperature 35 35.5 AType 300± 219 8 195 300± AC/N(Blue) AC/L(Brown) 63 SJTW 18AWGx2C 45.8 105 V(Black) V(Red) 12V,24V:SJTW 14AWGx2C 36V,42V,48V,54V:SJTW 18AWGx2C 4ψ4.5 : Max. Case Temperature 21.5 35 35.5 14 36 File Name:ELG150SPEC 1603
B/ DA/D2Type 300± 219 8 195 300± AC/N(Blue) AC/L(Brown) 63 SJTW 18AWGx2C 45.8 105 UL2517 22AWGx2C DIM(Blue)* DIM(White)** V(Black) V(Red) 12V,24V:SJTW 14AWGx2C 36V,42V,48V,54V:SJTW 18AWGx2C 4ψ4.5 : Max. Case Temperature 35 35.5 * DIM for BType DA for DAType PROG for D2Type * *DIM for BType DA for DAType PROG for D2Type Note1: Please connect the case to FG for the complete EMC deliverance. Note2: Please contact MEAN WELL for input wiring option with FG. Installation Manual Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html File Name:ELG150SPEC 1603