Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 00000000 40W Constant Voltage Constant Current LED Driver IP65 IP67 Metal housing with class I design Ⅰ current output. HLG40H operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 89.5%, with the fanless design, the entire series is able to operate for 40 ~ case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG40H is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. I I B D File Name:HLG40HSPEC 161025
SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE HLG40H12 HLG40H15 HLG40H HLG40H24 HLG40H30 HLG40H36 HLG40H42 HLG40H48 HLG40H54 DC VOLTAGE 12V 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 7.2 ~12V 9 ~ 15V 12 ~ V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V RATED CURRENT RATED POWER 3.33A 39.96W 2.67A 40.05W 2A 40W 1.67A 40.08W 1.34A 40.2W 1.12A 40.32W 0.96A 40.32W 0.84A 40.32W 0.75A 40.5W RIPPLE & NOISE (max.) Note.2 150mVpp 150mVpp 150mVpp 0mVpp 0mVpp 0mVpp 0mVpp 300mVpp 300mVpp VOLTAGE ADJ. RANGE Adjustable for AType only (via builtin potentiometer) 10.8 ~ 13.5V 13.5 ~ 17V 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 40 ~ 46V 44 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE Adjustable for AType only (via builtin potentiometer) 2 ~ 3.33A 1.6 ~ 2.67A 1.2 ~ 2A 1 ~ 1.67A 0.8 ~ 1.34A 0.67 ~ 1.12A 0.58 ~ 0.96A 0.5 ~ 0.84A 0.45 ~ 0.75A VOLTAGE TOLERANCE Note.3 ±2.5% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% LOAD REGULATION ±2.0% ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME Note.6 500ms,ms/115VAC 500ms,ms/ HOLD UP TIME (Typ.) 16ms / 115VAC, VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE SAFETY STANDARDS Note.5 Note.8 47 ~ 63Hz 0.43A / 115VAC 0.24A / 0.23A / 277VAC <0.75mA / 277VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed Shut down o/p voltage, repower on to recover OVER TEMPERATURE Shut down o/p voltage, repower on to recover WORKING TEMP. Tcase= 40 ~ (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase= ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~, 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY & EMC TOTAL HARMONIC DISTORTION SHORT CIRCUIT WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) PF 0.98/115VAC, PF 0.95/, PF 0.92/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< % (@ load % / 115VAC,; @ load 75% / 277VAC) (Please refer to " TOTAL HARMONIC DISTORTION (THD)" section) 86.5% 86.5% 88% 88% 88.5% 88.5% 88.5% 89.5% 89.5% COLD START 50A(t width=210 μs measured at 50% I peak) at ; Per NEMA 410 12 units (circuit breaker of type B) / units (circuit breaker of type C) at 15 ~ 21V 18 ~ 24V 23 ~ 30V 28 ~ 35V 35 ~ 43V 41 ~ 49V 48 ~ 58V 54 ~ 65V 59 ~ 68V UL8750 (type HL ), CSA C22.2 No. 250.008 (except for 48V, 54V), TUV EN613471, EN61347213 independent, IP65 or IP67 approved ; optional models for J613471, J61347213 ; design refer to UL9501, TUV EN9501, EN3351 I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Note.8 Compliance to EN55015, EN32 Class C (@ load %) ; EN33 EMC IMMUNITY Compliance to EN42,3,4,5,6,8,11; EN61547, EN55024, light industry level ( surge immunity LineEarth 4KV, LineLine 2KV) MTBF 1131.9K hrs min. Telcordia SR332 (Bellcore) ; 336.5K hrs min. MILHDBK217F (25 ) DIMENSION 171*61.5*36.8mm (L*W*H) PACKING 0.73Kg; pcs/15.6kg/0.9cuft File Name:HLG40HSPEC 161025
BLOCK DIAGRAM Fosc : KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT V V DIM DIM (B Type) O.V.P. DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. (min.) (C) Hiccup Protection 50 Io (%) Typical output current normalized by rated current (%) File Name:HLG40HSPEC 161025
DIMMING OPERATION AC/L(Brown) AC/N(Blue) FG (Green/Yellow) HLG40H V(Red) V(Black) DIM(Blue) DIM(White) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% % 70% % 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) % 90% % 70% % 50% 40% 30% % 10% 10% % 30% 40% 50% % 70% % 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) % 90% % 70% % 50% 40% 30% DO NOT connect "DIM to V" % 10% 10K/N K/N 30K/N 40K/N 50K/N K/N 70K/N K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLG40HSPEC 161025
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Swih Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG40H BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a swih and relay can turn ON/OFF the lighting fixture. File Name:HLG40HSPEC 161025
OUTPUT LOAD vs TEMPERATURE Input only Input only LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 70 (HORIZONTAL) 40 25 0 45 55 65 75 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 70 Constant Current Mode 1 90 0.99 0.98 0.97 0.96 0.95 70 PF 0.94 0.93 277VAC LOAD (%) 50 40 0.92 0.91 0.9 0.89 0.88 0.87 115VAC 0.86 90 125 135 145 155 165 175 1 0 230 305 0.85 50% % 70% % 90% % INPUT VOLTAGE (V) Hz LOAD (40W) Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 70 25 EFFICIENCY vs LOAD possess superior working efficiency that up to 89.5% can be reached in field applications. 48V Model, Tcase at 70 92 90 88 86 THD(%) 15 10 5 277VAC 115VAC EFFICIENCY (%) 84 82 78 76 74 277VAC 115VAC 72 0 50% % 70% % 90% % 70 10% % 30% 40% 50% % 70% % 90% % LOAD LOAD File Name:HLG40HSPEC 161025
LIFETIME 1 LIFETIME(Kh) 40 0 25 30 35 40 45 50 55 65 70 75 Tc a s e ( ) File Name:HLG40HSPEC 161025
MECHANICAL SPECIFICATION Blank/DType Case No.957B Unit:mm 171 11.9 147.2 9.6 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG 3C 32 46.5 61.5 30.75 73.6 ψ 4.2 4PL SVT 18AWG 2C V(Red) V(Black) : Max. Case Temperature 36.8 AType 171 11.9 147.2 9.6 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG 3C 32 46.5 61.5 30.75 73.6 Io ADJ Vo ADJ ψ 4.2 4PL SVT 18AWG 2C V(Red) V(Black) : Max. Case Temperature BType 171 11.9 147.2 9.6 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG 3C 32 46.5 61.5 30.75 73.6 ψ 4.2 4PL SVT 18AWG 2C UL 2517 18AWG 2C V(Red) V(Black) DIM(Blue) DIM(White) : Max. Case Temperature 36.8 36.8 File Name:HLG40HSPEC 161025
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG40H to operate in dry/wet/damp or outdoor environment. AC source I/P HLG40H O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG40H O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:HLG40HSPEC 161025