Sideboard ssembly Instructions - lease keep for future reference 041 xx 5535 Dimensions Width - 117.2cm Depth - 38.8cm eight - 73.6cm Important - lease read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer elpline: 01709534123 lease turn to back page for important information when contacting Customer elpline. Rev - 01/02/2017
Safety and Care dvice Important - lease read these instructions fully before starting assembly Check you have all the components and tools listed on pages 2 and 4. Remove all fittings from the plastic bags and seperate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Do not stand or put weight on the product, this could cause damage. ssemble the item as close to its final position (in the same room) as possible. ssemble on a soft level surface to avoid damaging the unit or your floor. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. nly use hand screwdrivers. Do Not dispose of packaging until assembly complete. Make sure you have enough space to layout the parts before starting. arts of the assembly will be easier with 2 people. Dispose of all packaging carefully and responsibly when assembly complete. Care and maintenance To protect the furniture, position the furniture out of direct sunlight and away from direct heat sources such as radiators and fires. Do not place the furniture in excessively dry and humid conditions. From time to time check that there are no loose screws on this unit. lways lift furniture when moving it (do not drag) otherwise the joints may be damaged. Do not place hot or cold objects on the surface, always use protective mats to avoid marking the furniture. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Clean spills up immediately Dust surfaces with a soft, dry, lint free cloth. More stubborn marks can be removed using a damp (not wet) cloth. Wipe the surface dry immediately using a soft lint free cloth. Do not use detergants, abrasive cleaning products or cleaning products that contain ammonia, solvents or silicone as these may damage the surface finish. 1
Components - anels lease check you have all the panels listed below Important - Thick lines indicate finished edges Front Grooved edge Front Grooved edge Left hand end (72x35.8cm) Right hand end (72x35.8cm) Code - 9160 Code - 9161 Left hand division (62.8x32cm) Code - 9162 Right hand division (62.8x32cm) Code - 9163 linth x 1 (110.2x7.6cm) Code - 9164 Top (117.2x38.8cm) Code - 7397 Trim x 2 (72cm long) Code - 684xx6530 ottom (110.2x32cm) Code - 7398 Drawer front x 4 (37.2x15.7cm) Code - 7292 Door x 2 (63.6x35.9cm) Code - 7293 Drawer bottom x 4 (33.8x29.8cm) Code - 2601 Shelf x 2 (35.5x30.0cm) Code - 7404 ackpanel (111.2x64.6cm) Code - 7419 Left drawer side x 4 (30x10cm) Drawer back x 4 (32.7x10cm) Right drawer side x 4 (30x10cm) Code - 622xx7002 Code - 624xx7004 Code - 623xx7002 2
Components - Exploded View Important - Thick lines indicate finished edges 684xx6530 Trim 9160 7397 7419 7404 7293 9162 9163 7404 7398 9161 622xx7002 624xx7004 7293 7292 623xx7002 9164 2601 684xx6530 Trim 3
Components-Fittings lease check you have all the fittings listed below If you have damaged or missing components, call the Customer elpline: 01709 534123 lease turn to back page for important information when contacting Customer elpline. Note: The quantities below are the correct amount to complete the assembly, In some case more fittings may be supplied than are required. C Large cam x 16 - Code 760001103 Metal dowel x 24 - Code 760003004 Small cam x 8 - Code 760003005 D E F 12mm screw x 8 - Code 690001008 anel pin x 14 - Code 760001012 anel pin guide x 1 Code 684004501 G 18mm bolt x 12 - Code 700002021 Runner x 8 - Code 760001040 9mm bolt x 8 - Code 690001078 I J andle x 6 Code 644xx3511 L 45mm screw x 4 - Code 690001075 M Shelf stud x 8 Code 681003001 N Wooden dowel x 4 Code 770001006 Fully cranked 26mm hinge x 4 Code 652001120 ingeplate x 4 Code 653006000 8mm screw x 16 Code 700003510 T anel older x 3 Code 680003505 U L racket x1 Code 760001901 V Screw x 2 Code 690001099 Tools required Cross headed screwdriver (small & large ) Tape Measure radawl Small ammer Eye protection (when using a hammer) Ruler - Use this ruler to help correctly identify the screws 0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 4
ssembly Instructions Step 1 Fitting dowels to top panel (x8) 7397 Note: Insert metal dowels as far as shown by arrows. Do not over tighten. Step 2 Fitting cams to plinth and bottom panel Large (x8) 9164 7398 Note: Ensure cam arrow points towards the edge with hole. Step 3 Fitting cams and dowels to left and right hand end panels Large (x4) (x8) Front grooved edge Note: Ensure cam arrow points towards the edge with hole. 9160 9161 5 Note: Insert metal dowels as far as shown by arrows. Do not over tighten. Front grooved edge
ssembly Instructions Step 4 Fitting hingeplates to left hand end panel (x2) 9160 Step 5 Fitting hingeplates to right hand end panel Front grooved edge (x2) Notch in ingeplate points towards grooved edge. Front grooved edge Front grooved edge 9161 Notch in ingeplate points towards grooved edge. Step 6 Fitting cams and wooden dowels to the division panels. Large N (x4) (x4) N N N Use a hammer to knock in wooden dowels N into inner holes. N N 9162 Note: Ensure cam arrow points towards the edge with hole. 9163 6
ssembly Instructions Step 7 ttaching runners a: lign the drawer runner with the finished edge of panel 9162, the 2nd hole from the front will then line up with a pre-drilled hole, secure the runner to the panel using screws. (x4) (x8) a: Note: lease note gap from the front grooved edge. Note: Ensure these holes are positioned as shown. 9162 Front finished edge b: Slide the drawer runner forward to secure screws. The 2nd to last hole in the runner will line up with the pre-drilled holes in the panel. b: 2ND 9162 7
ssembly Instructions Step 8 ttaching runners a: lign the drawer runner with the finished edge of panel 9163, the 2nd hole from the front will then line up with a pre-drilled hole, secure the runner to the panel using screws. (x4) Front finished edge (x8) a: Note: lease note gap from the front grooved edge. Note: Ensure these holes are positioned as shown. 9163 b: Slide the drawer runner forward to secure 2 screws. The hole in the runner will line up with the pre-drilled holes in the panel. 9163 2ND b: 8
ssembly Instructions Step 9 ttach hinges and handles to doors D (x4) G (x8) J (x2) (x4) Important: a: Insert hinges into holes, ensure the hinge is straight (90 degree angle). a: 7293x2 90 b: 98 b: efore securing the 7293x2 hinges, we recommend you pre - mark the doors using a bradawl. radawl D c: D c: Secure hinges to doors 7293 using screws D. D D 7293x2 D D d: d: Secure handle doors 7293 using bolts G. 9 J to G G 7293x2 J
ssembly Instructions Step 10 Drawer assembly (x8) a: a: Insert dowels into drawer fronts 7292. Note: Insert metal dowels as far as shown by arrows. Do not over tighten. 7292 C C (x8) Small b: Right hand side 623xx7002 b: Insert small cams C into left 622xx7002 and right 623xx7002 drawer sides. Note: Ensure cam arrow points towards the edge with hole. Left hand side 622xx7002 C C c: Insert wooden dowels in drawer back 624xx7004 into holes in left 622xx7002 right 623xx7002 hand drawer sides. Left hand side 622xx7002 c: Drawer ack 624xx7004 Continued on next page. Right hand side 623xx7002 10
ssembly Instructions Step 10 - Continued Drawer assembly Continued... d: d: Slide drawer bottom 2601 into grooves in left,right drawer sides and drawer back. Ensure foil on the drawer bottom is facing upwards. 2601 FIL FCE e: Insert cams C already inserted in left and right drawer sides onto dowels in drawer fronts 7292. e: C 7292 Turn cam 180 degrees to lock f: Secure handles J to drawer fronts 7292 using bolts G. G J (x8) (x4) G f: G 7292 Repeat with remaining 3 drawers. J 11
ssembly Instructions Step 11 ttach right hand end panel, left hand division and right hand divsion to the top panel 9162 Locate cams in panels 9161, 9162 and 9163 onto dowels in top panel 7397. Then lock. 9161 9163 7397 Front finished edge Front grooved edge Turn cam 180 degrees to lock Step 12 ttach bottom panel to right hand end panel Locate cams in panel 7398 onto dowels in right hand end panel 9161. Then lock. 7398 Turn cam 180 degrees to lock 9161 12
ssembly Instructions Step 13 Secure bottom panel to left and right hand divisions L (x4) Locate wooden dowels N already inserted in divisions 9162 and 9163 into holes in bottom panel 7398. Now locate screw L through holes in bottom panel 7398 and screw into holes in divisions 9162. and 9163. L L L L 7398 9163 L 9162 Step 14 ttach plinth to right hand end panel Locate cams in panel 9164 onto dowels in right hand end panel 9161. Then lock. 9164 9161 Turn cam 180 degrees to lock 13
ssembly Instructions Step 15 ttach left hand end to top, bottom and plinth Locate cams in panel 9160 onto dowels in top panel 7397. Then lock. Locate dowels in left hand end panel 9160 into cams in bottom 7398 and plinth 9164. Then lock. 9164 7398 9160 7397 Turn cam 180 degrees to lock Step 16 Locate backpanels into grooves in left and right hand end panels and top panel Important: 2 people required 7419 lain chipboard surface Important: You do not have to turn your unit round it is shown this way just to show how backpanel is located. Locate backpanel 7419 into grooves in left hand end 9160 and right hand end 9161 slide the backpanel 7419 into groove in top 7397. 9160 9161 7397 14
ssembly Instructions Step 17 Lay unit down to square unit up Warning: 2 people to lift. Lift with care. YY DIG 1 XX Measure to external corners 7397 XX 9160 Important: Ensure a tape measure is used to square up unit! efore securing the back it is necessary to square up the unit. You can do this by measuring between XX - XX and YY - YY ensuring these are the same (DIG 1). If they are not (DIG 2) pply slight pressure as indicated (DIG 3) until they are the same. XX YY XX YY XX DIG 2 DIG 3 YY XX YY YY XX YY 9161 XX YY Step 18 Secure backpanel to bottom panel. F E T (x1) (x14) (x3) E 7419 Secure backpanel to bottom panel and divisions using panel pins E. Use the panel pin guide F when locating the panel pins E. This will hold the panel pins vertical and ensure the correct distance from the edge. You cannot use panel pin guide when securing backpanel to divisions. E E 7419 50mm 50mm 365mm T T 365mm F T 7398 E Slide the thin point of the stability blocks T between the back panel and the grooves in the top and end panels. 7398 nce inserted fully, tighten the screws in the stability blocks. 15 T
ssembly Instructions Step 19 ttach trim Turn unit over. Trims (x2) Warning: 2 people to lift. Lift with care. 9160 Locate the notch on trim into groove on left 9160 and right 9161 ends. Ensure the trims are positioned correctly. 9161 To insert trims use a hammer, place a cardboard packing piece between the hammer and trims to protect the trims. Your trims may have a protective film on. lease remove this after assembly. 16
ssembly Instructions Step 20 Lift unit up and locate drawers Warning: 2 people to lift. Lift with care. I (x8) For this step we recommend you follow the helpful hints page on page 18. I 7292 I 2nd LE 17
ssembly Instructions Step 20 - continued Locate drawers helpful hints a: ull sliding part of drawer runners out so they are fully extended. a: b: b: Locate drawer onto runners. c: Locate screwdriver into second threaded hole in drawer runner. c: d: d: Keeping screwdriver in place push the drawer closed.the screwdriver will push against the divisions and extend the drawer runner. 2nd hole e: ull drawer out slowly and line the hole in the drawer side with the 2nd threaded hole in the runner. Now insert screw l through the drawer side and into threaded hole in runner. e: f: I 2nd hole f: Now insert screw l through the drawer side and into threaded hole in runner. 18
ssembly Instructions Step 21 Locate shelf studs M ush shelf studs M into panels 9160, 9161, 9162 and 9163. (x8) M M 9160 M 9163 9161 Step 22 Locate shelves onto shelf studs Locate shelves 7404 onto shelf studs M 7404 7404 19
ssembly Instructions Step 23 anging doors a: With help, slot door hinges onto hinge plates. Ensure screw on hinge slides into the slot on hingeplate. See Diagrams 1,2 and 3. 7293 a: b: Tighten screw shown to lock hinges in position. b: Repeat a and b for opposite door. See inge adjustment in step 24 if the doors need adjusting. Diagram 1 Underside view Ensure the underside of screw slides into slot on hingeplate. Diagram 2 inge correctly attached to hingeplate. Diagram 3 inge incorrectly attached to hingeplate. 20
ssembly Instructions Step 24 inge adjustment a: a: To move doors up or down: loosen screws shown and move doors to suit. Re-tighten screws. b: To move doors in or out: loosen screw shown and move doors to suit. Re-tighten screws. b: c: To move doors left or right: loosen or tighten screw as shown. c: e careful not to fully unscrew. 21
ssembly Instructions Step 25 Fixing to wall We recommend that this unit is fixed to a suitable wall to prevent possible overbalancing. We have included a fixing bracket for this. No fixing screws are provided as they will need to suit the wall type, and the length of screw will depend on the distance from the back of the unit to the wall. lease ensure fixings used are appropriate to your wall type. Locate the bracket to the top panel or to the end panel as close to top as possible. We do not specify exact location for the bracket, this is left to the customer s discretion. With help move the unit into position. Warning: 2 people to lift. Lift with care. Warning: lease take care when drilling into the wall, avoiding any pipes and wires. Wear safety goggles when drilling. The use of residual current device (RCD) is recommended when working with tools.if in doubt consult a qualified person. U x1 V x2 22
Congratulations! your unit is complete. Important Information If you need help or have damaged or missing parts, call the Customer elpline: 01709 534123 Simply contact us on CUSTMER ELLINE : 01709 534123 etween 8am - 4.30pm Monday to Thursday and 8am - 2.30p.m friday. Your statutory rights are not affected. lease have the following information: Unit Description, roduct Code, roduct Colour, lace of urchase, Catalogue Ref. No., Item Code, and have the assembly instructions close to hand. We do have an answer machine should you contact us out of office hours, so in addition to the above information could you leave your name, address, daytime telephone number and the nature of your call on the answerphone. ll calls will be actioned asap. You can also e-mail your requests to us at: customer.helpdesk@addspacefl.co.uk lternatively Write to us at: Customer Service Department, ddspace Furniture Limited, raithwell Way, ellaby Industrial Estate, ellaby, Rotherham, South Yorkshire, S66 8Y. 23