DESIGN OF THERMOELECTRIC ENERGY HARVESTER USING LTC 3108 BOOST CONVERTER MUHAMMAD ZULHAIZER BIN AB RASHID This Report Is Submitted In Partial Fulfillment Of Requirements For The Bachelor Degree of Electronic Engineering (Industrial Electronic) Fakulti Kejuruteraan Elektronik dan Kejuruteraan Komputer Universiti Teknikal Malaysia Melaka June 2013
UNIVERSTI TEKNIKAL MALAYSIA MELAKA FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER BORANG PENGESAHAN STATUS LAPORAN PROJEK SARJANA MUDA II Tajuk Projek : Sesi Pengajian Design Of Thermoelectric Energy Harvester Using LTC3108 Boost Converter : 0 8 / 0 9 Saya MUHAMMAD ZULHAIZER BIN AB RASHID mengaku membenarkan Laporan Projek Sarjana Muda ini disimpan di Perpustakaan dengan syarat-syarat kegunaan seperti berikut: 1. Laporan adalah hakmilik Universiti Teknikal Malaysia Melaka. 2. Perpustakaan dibenarkan membuat salinan untuk tujuan pengajian sahaja. 3. Perpustakaan dibenarkan membuat salinan laporan ini sebagai bahan pertukaran antara institusi pengajian tinggi. 4. Sila tandakan ( ) : SULIT* *(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia seperti yang termaktub di dalam AKTA RAHSIA RASMI 1972) TERHAD** **(Mengandungi maklumat terhad yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan) TIDAK TERHAD Disahkan oleh: (TANDATANGAN PENULIS) (COP DAN TANDATANGAN PENYELIA) Tarikh:.. Tarikh:..
iii I declare that this thesis entitled Design of Thermoelectric Energy Harvester Using LTC3108 Boost Converter is the result of my own research except as cited in the references. The thesis has not been accept for any degree and is not concurrently submitted in candidature for any other degree. Signature : Author : MUHAMMAD ZULHAIZER BIN AB RASHID Date : 10 th JUNE, 2013
iv I hereby declare that I have read this thesis and in my opinion this thesis is sufficient in term of scope and quality for the award of the Bachelor of Electronic Engineering (Electronic Industries) With Honours Signature : Supervisor name : ENGR HAZLI RAFIS BIN ABDUL RAHIM Date : 10 th JUNE, 2013
Specially dedicated to my beloved parents, family members and fellows friend v
vi APPRECIATION First of all, praise to Allah S.W.T., because of His grace, I was able to implement my final year project till the end without any problems. I want to take this opportunity to express my appreciation to those who have helped me a lot throughout completing my PSM whether directly or indirectly. Special thanks to my family especially both of my parent who non-stop gave me morale supports and financial resources. Thanks also to my supervisor, Eng. Hazli Rafis Bin Abdul Rahim, for guiding me throughout getting an analysis and also gave some advice for my project. Lastly for my love, housemate and fellow friends, thank you so much for helped me out when I need an idea or something that related with my project. I express my gratitude for everyone that I not mention above and hope God will repay you well one day.
vii ABSTRACT Renewable energy technique is the process of converting available ambient energy into usable electrical energy through the use of a particular material or transduction mechanism. Nowadays, the evolution of new technology which involving renewable energy technique and smart grid system has a huge potential in the energy market. In line with the current technology interest in the smart grid technology, power transformer health condition becomes one of the main issue need to be considered. The way to monitor health condition of the power transformer has started to evolve from typical monitoring technique to a new development of using energy harvesting technology to activate sensors network for the monitoring purpose. For this project, Thermoelectric Power Generator (TEG) is used to convert the heat energy get from the power transformer into small electrical energy in order to power up electronic devices that will triggering up the monitoring system. TEG only produces small electrical energy, so the boost converter is needed in order to increase the electrical energy from the TEG and get its maximum power point tracking (MPTT). The boost converter is a type of DC-to-DC converter which has a greater output than the input voltage. So, the result of this project will show us the small electrical energy, converted from the heat energy, range between 20 mv to 1.5V that is get from the TEG will be raised up until at least 5V using a boost converter. 5V is the minimum volts to trigger up the PIC circuit or any others small electronic appliance that has low power consumption.
viii ABSTRAK Teknik tenaga boleh diperbaharui adalah proses menukarkan tenaga ambien yang sedia ada kepada tenaga elektrik yang boleh digunakan melalui penggunaan bahan tertentu atau mekanisme transduksi. Kini, perkembangan teknologi baru yang melibatkan teknik tenaga boleh diperbaharui dan sistem grid pintar mempunyai potensi yang besar dalam pasaran tenaga. Selaras dengan kepentingan teknologi semasa dalam teknologi grid pintar, keadaan transformer kuasa menjadi salah satu isu utama yang perlu dipertimbangkan. Cara untuk memantau keadaan transformer kuasa telah berubah mengikut peredaran masa sehinggalah penghasilan teknologi baru melalui penuaian tenaga untuk menghidupkan rangkaian sensor sebagai tujuan pemantauan.untuk projek ini, penjana thermoelectric (TEG) digunakan untuk menukarkan tenaga haba yang diperolehi daripada transformer kuasa kepada tenaga elektrik kecil yang mampu menghidupkan alat-alat elektronik yang akan mencetuskan satu sistem pemantauan. TEG akan menghasilkan tenaga elektrik kecil, jadi penukar tingkat diperlukan dalam usaha untuk meningkatkan tenaga elektrik daripada TEG dan mendapatkan pengesanan titik kuasa maksimum (MPTT). Penukar tingkat adalah sejenis penukar DC ke DC yang mempunyai keluaran yang lebih besar daripada voltan masukan. Jadi, hasil daripada projek ini akan menunjukkan kepada kita tenaga elektrik kecil, ditukar daripada tenaga haba, julat antara 20 mv sehingga 1.5V yang didapati daripada TEG akan ditingkatkan sehingga sekurang-kurangnya 5V menggunakan penukar tingkat. 5V adalah volt minimum untuk menghidupkan litar PIC atau mana-mana perkakas elektronik lain yang mempunyai penggunaan kuasa yang rendah.
ix TABLE OF CONTENTS CHAPTER CONTENT PAGES PROJECT TITLE DECLARATION DEDICATION APPRECIATION ABSTRACT ABSTRAK TABLE OF CONTENTS LIST OF TABLES LIST OF FIGURES LIST OF ABBREVIATIONS LIST OF APPENDICES i iii v vi vii viii ix xiii xiv xvi xvii
x I INTRODUCTION 1.1 Project Introduction 1 1.2 Project Objective 5 1.3 Problem Statement 5 1.4 Scope of Work 6 1.5 Brief Description of Methodology 6 1.6 Report Overview 6 II BACKGROUND STUDY / LITERATURE REVIEW 2.1 Basic Understanding of Boost Converter (Ideal Circuit) 8 2.1.1 Mathematical Model of Boost Converter 11 2.2 Literature Review From Related Journal 12 2.3 Basic Introduction Based On Literature Review 17 2.3.1 List of Hardware Involved 17 2.3.1.1 TEG 17 2.3.1.2 LTC3108 IC 21 2.3.1.2.1 Pin Configuration of LTC3108 22 2.3.1.2.2 Operation of LTC3108 26 2.3.1.3 SMT Component 33 2.3.1.3.1 History of SMT 35
xi 2.3.1.3.2 Advantage and Disadvantage of SMT 36 2.3.1.3.3 Type and Size of SMT Component 38 2.3.1.4 Custom Made Double Layer PCB 39 2.3.2 List of Software Involved 40 III RESEARCH METHODOLOGY 3.1 Project Background 41 3.2 Project Methodology 43 3.2.1 Phase of Method and Approach 3.2.1.1 First Phase (Literature Review) 45 3.2.1.2 Second Phase (Design, Simulation and Analysis) 45 3.2.1.3 Third Phase (Implementation) 49 3.2.1.4 Fourth Phase (Thesis Writing) 49 IV RESULT AND DISCUSSION 4.1 Introduction 50 4.2 Structure of the System 51 4.3 Final Design 52 4.3.1 Circuit Diagram (Schematic) 52 4.3.2 Circuit Diagram (PCB Layout) 53
xii 4.3.2.1 Pin Name and Function 54 4.4 Final Product 55 4.5 Analysis of TEG and LTC3108 Boost Converter 58 4.5.1 Voltage Output Versus Current (TEG) 58 4.5.2 Temperature Versus V out (TEG) 59 4.5.3 Vin Versus Vout (LTC3108 Boost Converter) 60 4.6 Final Output of LTC3108 Boost Converter 62 4.7 Final Discussion 62 V CONCLUSION AND RECOMMENDATION 5.1 Conclusion 63 5.2 Potential of Commercialization 64 5.3 Recommendation 64 REFERENCES 65 APPENDICES 67
xiii LIST OF TABLES NO. DESCRIPTION PAGES 2.1 Pin Function of LTC3108 23 2.2 Regulated Voltage Using Pins VS1 and VS2 25 2.3 Operation of LTC3108 27 4.1 Pins Name and Its Function 54
xiv LIST OF FIGURES NO. DESCRIPTION PAGES 1.1 Power Transformer in Distribution System 2 1.2 Hot Spot Measurement of High Voltage Transformer 3 2.1 Basic Circuit of Boost Converter 10 2.2 ON and OFF State of Basic Boost Converter 11 2.3 Example of TEG Device 18 2.4 The Seebeck Effect Due To Temperature Gradient 19 2.5 Basic Structure of Thermoelectric Couple 20 2.6 Equivalent Thermoelectric Model 21 2.7 Pin Configuration of LTC3108 23 2.8 Block Diagram of LTC3108 27 2.9 Output Voltage Sequencing with Vout Programmed for 3.3V (Time Not to Scale) 33
xv 2.10 Comparison between SMT Component (left) with Through-hole Component (right) 34 2.11 Surface-mount Capacitor 34 2.12 Size of SMT Component 38 3.1 Flow of Project 43 3.2 Methodology Flowchart 44 4.1 Structure of the System 52 4.2 Schematic Diagram of the Project 53 4.3 PCB Layout Diagram of the Project 54 4.4 Final Product Using LTC3108 IC And Surface Mount Component 56 4.5 Real Size of the Product Which Is Compact 57 4.6 Final Product Inside the Packaging 57 4.7 Vout, V VS Current,I 59 4.8 Temperature, C VS Vout, V 60 4.9 Vin, V VS Vout, V 61 4.10 Final Output 62
xvi LIST OF ABBREVIATIONS TNB Tenaga Nasional Berhad TEG Thermoelectric Generator V - Voltage PIC Programmable Integrated Circuit IC Integrated Circuit DC Direct Current PWM Pulse Width Modulator SMD Surface Mount Device SMT Surface Mount Technology PMC Power Management Circuit PCB Printed Circuit Board I Current C - Celcius
xvii LIST OF APPENDICES (noted that the appendix section is start at page 67) NO. DESCRIPTION PAGES A ELECTRICAL AND TYPICAL PERFORMANCE CHARACTERISTIC OF LTC3108 APPENDIX A-1 B TYPE OF SMT PACKAGE APPENDIX B-1 C GAANT CHART APPENDIX C-1 D COMPONENT SELECTION APPENDIX D-1
1 CHAPTER I INTRODUCTION 1.1 Project Introduction Renewable energy technique is the process of converting available ambient energy into usable electrical energy through the use of a particular material or transduction mechanism. Nowadays, the evolution of new technology which involving renewable energy technique and smart grid system has a huge potential in the energy market. Although the application of new technology in the smart grid system has evolved rapidly, devices such as power transformer is still be a major component in the power distribution system. Thus, in line with the current technology interest in the smart grid technology, power transformer health condition becomes one of the main issues considered.
2 Figure 1.1: Power Transformer In Distribution System In this situation, the health condition of power transformer is about how much the heat generate during the transformer operated. Heat is generated due to the high voltages that need to be step-up or step-down by the transformer. Overheat may cause minor or major damage to the transformer and this will affect the performance of the transformer and this also will lead to failure of the transformer. So to reduce and overcome this problem, we must have a device that could monitor the heat generate by the power transformer. This monitoring system will be used to inform the relevant authority, for example Tenaga Nasional Bhd. (TNB) or other electric supply company, whether the temperature of the transformer is in control or not. This will allowed them to make any maintenance before the transformer malfunction or get any another major damage.
3 Figure 1.2: Hot Spot Measurement of High Voltage Transformer The way to monitor power transformer has started to evolve from typical monitoring technique to a new development of using energy harvesting technology to activate sensors network for the monitoring purpose. The ambient heat energy obtained from the power transformer will be harvested to turn on power electronic compensator and driven the sensors. In producing an auto monitoring system for the power transformer, the Thermoelectric Power Generator (TEG) can be used as a device which will generate a small electrical energy. Normally TEG will generate an electrical voltage between 20 mv to 1.5 V, depend from the heat generated. When the temperature increases, the voltage generated also increases. The output of TEG is normally very small and varies. This is because the output is depend on the temperature different between 2 different plate inside the TEG, so this small electrical energy need to be boost up to a higher level which can be used to triggering up the PIC circuit. Normally PIC usually need around 5V to 5.5V to be operated. Therefore, the input get from the TEG must be boost up at least 5V to let the PIC switch ON. There are two function of this PIC circuit in this situation. First, PIC circuit is used to triggering up the communication device such as Zigbee or Xbee to the user. Secondly, this PIC circuit reads the surrounding heat temperature using a heat sensor so that this temperature reading can be sent through the
4 communication device and be used by the user whether the temperature of power transformer is still in control or not. This project only covered up until the operation of TEG and the design a boost converter which used LTC3108 IC and also Surface Mount Device (SMD). This design of boost converter must be compact and able to step-up the voltage produce by the TEG which in range between 0.7V to 1.5V into a minimum output level which is at least 5V. The LTC3108 is a highly integrated DC-DC converter ideal for harvesting and managing surplus energy from extremely low input voltage sources such as TEGs thermopiles and small solar cells. The step-up topology operates from input voltages as low as 20mV. Using a small step-up transformer, the LTC3108 provides a complete power management solution for wireless sensing and data acquisition. The 2.2V LDO powers an external microprocessor, while the main output is programmed to one of four fixed voltages to power a wireless transmitter or sensors. The power good indicator signals that the main output voltage is within regulation. A second output can be enabled by the host. A storage capacitor provides power when the input voltage source is unavailable. Extremely low quiescent current and high efficiency design ensure the fastest possible charge times of the output reservoir capacitor. The LTC3108 is available in a small, thermally enhanced 12-lead (3mm 4mm) DFN package and a 16-lead SSOP package.
5 1.2 Project Objective i. To design a compact DC-DC boost converter using LTC3108 IC and SMD in order to increase and stabilize the output voltage generated from the TEG. ii. To demonstrate experimentally DC/DC boost converter using LTC3108. iii. To analyze and evaluate the characteristic of TEG and output range produced from the boost converter whether it capable to supply a sufficient voltage and activated at least small electronic devices. 1.3 Problem Statement i. TEG generated power which is varies, intermittent and limited, so the power management circuit (PMC) using DC-DC boost converter which use an LTC3108 and SMD component can be used to stabilize the power to the load and also extract maximum power. ii. The needs of alternative power supply to power the sensor system to grant the effectiveness of the sensor system. iii. The maintenance cost to change the battery is a big issue as batteries is known to have short lifetime iv. A renewable energy is an energy that have a large potential in the market nowadays, so we need to design a new source of energy using a renewable energy to power up small or low voltage device by manipulating an energy harvesting technique
6 1.4 Scope of Work i. Determine the output voltage that can be harvested from the TEG circuit based on temperature different from surrounding. This output voltage will be used as an input to the boost converter circuit. ii. Developed circuit which is used to power up the PIC circuit that involving the TEG and boost converter using LTC3108 IC, SMD component and fabricated circuit. Where SMD component consists of resistor, capacitor and small transformer. 1.5 Report Overview Design of Thermoelectric Energy Harvester using LTC3108 boost converter is the title of this report where it contains a combination of five chapters from the introduction of this project to the outcome, expected result and conclusion of this project. The report is written in detail on each of every step to take under consideration on the progression of the project. Chapter 1 elaborate briefly what the project is all matter. Here clearly stated the background of the project, the objective, the scope of work of this project, brief description of methodology and the overview of each of the chapter contains. Chapter 2 is some of the literature review from an article, paper work, book, website and all the written text that are related to the project topic. Where in this thesis, it is included a literature review on TEG, Boost converter, SMD component and LTC3108 as all of the materials is used in this project.
7 Chapter 3 is on the methodology of overall project. It will discuss about the project background and also project methodology. At project methodology we will discuss further the way how this project will going on. It is not limited to the hardware choose, it also discuss on the software implementation choose. Chapter 4 will discuss about the result that had been obtain from the project such as the structure of the system, finished product and analysis taken. This chapter also we will discuss about the overall data that have been collected. Chapter 5 will concludes the overall view of the project. This chapter will summarize the findings of the project, analysis achievement, potential of commercialization and suggest further research for the future.