Page 1 of 52 RF Test Report PRODUCT DESIGNATION BRAND NAME TEST MODEL CLIENT : Dual Band Mobile Radio : VGC : VR 6600PRO, VR 6610, VR 6700, VRP 6000, VRP 6800 : VERO GLOBAL COMMUNICATION CO.,LTD DATE OF ISSUE : Apr.24, 2015 ETSI EN 301 783 1 V1.2.1 2010 07 STANDARD(S) : ETSI EN 301 783 2 V1.2.1 2010 07 REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.
Page 2 of 52 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr.24, 2015 Valid Original Report
Page 3 of 52 TABLE OF CONTENTS 1.TEST RESULT CERTIFICATION 4 2.EUT DESCRIPTION 5 3.TEST METHODOLOGY 6 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS 6 3.2 DESCRIPTION OF TEST MODES 6 4.FACILITIES AND ACCREDITATIONS 7 4.1 FACILITIES 7 5.SETUP OF EQUIPMENT UNDER TEST 7 5.1 SETUP CONFIGURATION OF EUT 7 5.2 SUPPORT EQUIPMENT 7 5.3 MEASUREMENT UNCERTAINTY 7 6.CONFORMANCE REQUIREMENT 8 6.1 MAXIMUM POWER (CONDUCTED) 8 6.2 CONDUCTED SPURIOUS EMISSION IN TRANSIMIT MODE 10 6.3 CONDUCTED SPURIOUS EMISSION IN RECEIVE OR TRANSIMIT STANDBY MODE 16 6.4 RADIATED SPURIOUS EMISSION 22 6.5 RADIATED SPURIOUS EMISSION 29 6.6 CONDUCTED RF IMMUNITY 33 APPENDIX 1 36 PHOTOGRAPHS OF TEST SETUP 36 APPENDIX 2 37 PHOTOGRAPHS OF EUT 37
1. TEST RESULT CERTIFICATION Page 4 of 52 Applicant: Manufacturer: Product Designation: Brand Name: Model Name: Series Model Difference description VERO GLOBAL COMMUNICATION CO.,LTD No.3 Chongxiang St, Quanzhou Economic & Technological Development Zone, Fujian, P.R.C 362006 VERO GLOBAL COMMUNICATION CO.,LTD No.3 Chongxiang St, Quanzhou Economic & Technological Development Zone, Fujian, P.R.C 362006 Dual Band Mobile Radio VGC VR-6600PRO VR-6610, VR-6700, VRP-6000, VRP-6800 All the same except for the model name. Date of Test: Apr.17, 2015 to Apr.23, 2015 The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in the European Standard ETSI EN 301 783-1/-2. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested by Steven Zhou Apr.24, 2015 Checked By Kidd Yang Apr.24, 2015 Authorized By Solger Zhang Apr.24, 2015
Page 5 of 52 EUT DESCRIPTION Product Brand Name Model Name Hardware Version Software Version Operation Frequency Modulation Type Operation Mode Channel Separation Rated Output Power Antenna Designation Antenna type Antenna gain Dual Band Mobile Radio VGC VR-6600PRO N/A N/A VHF: 144~146MHz UHF: 430~440MHz F3E Push to talk 12.5 KHz, 25 KHz 50W (It was fixed by the manufacturer, any individual can t arbitrarily change it.) Detachable External antenna 0dBi Power Supply DC 13.8V Test Frequencies: VHF: 144.025MHz, 145.000MHz, 145.975MHz UHF: 430.025MHz, 435.000MHz, 439.975MHz (Near lowest, near middle & near highest frequencies in the frequency range of operation.) Note: For more details, please refer the user s manual
2. TEST METHODOLOGY Page 6 of 52 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: ETSI EN 301 783-1 2010-07: Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Commercially available amateur radio equipment; Part 1: Technical characteristics and methods of measurement ETSI EN 301 783-2 2010-07: Electromagnetic compatibility and Radio spectrum Matters (ERM);Land Mobile Service; Commercially available amateur radio equipment; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive 3.2 DESCRIPTION OF TEST MODES 1. The EUT has been tested under typical operating condition. No software used to control the EUT for staying in transmitting and receiving mode for testing.
4. FACILITIES AND ACCREDITATIONS 4.1 FACILITIES Page 7 of 52 Site Location Attestation of Global Compliance (Shenzhen) Co., Ltd B112-B113 Building 12, Baoan Building Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen, Guangdong, P.R.China 5 SETUP OF EQUIPMENT UNDER TEST 5.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 5.2 SUPPORT EQUIPMENT No available support equipment during the testing. Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. 5.3 Measurement uncertainty Radio frequency: 1 10-7 RF Power(up to 160W): 0.5dB Radiated RF power: 4dB Conducted spurious emission of transmitter valid up to 12.75 GHz: 2.75dB Conducted spurious emission of receiver, valid up to 12.75 GHz: 4.2dB Two-signal measurement, valid up to 4 GHz: 2dB Radiated emission of the transmitter, valid up to 4GHz: 3dB Radiated emission of the receiver, valid up to 4 GHz: 3dB
6. CONFORMANCE REQUIREMENT Page 8 of 52 6.1 MAXIMUM POWER (CONDUCTED) TEST CONFIGURATION Note: The impedance of attenuator is 50ohm. TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1 (V.1.2.1) Sub-clause 4.2 for the test conditions. 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.1.2 for the measurement method. 3. Note: 1. The EUT have been tested under DC 13.8V. 2. Only result the worst case in this part. TEST RESULT:
FM 12.5 KHz Channel Separation Page 9 of 52 modulation Channel Channel Separation Output power (dbm) 50W Low (VHF) 12.5 KHz 46.93 Middle (VHF) 12.5 KHz 46.97 High (VHF) 12.5 KHz 46.96 25 KHz Channel Separation modulation Channel Channel Separation Output power (dbm) Low (VHF) 25 KHz 46.94 FM 50W Middle (VHF) 25 KHz 46.97 High (VHF) 25 KHz 46.98 12.5 KHz Channel Separation modulation Channel Channel Separation Output power (dbm) Low (UHF) 12.5 KHz 46.96 FM 50W Middle (UHF) 12.5 KHz 46.95 High (UHF) 12.5 KHz 46.97 25 KHz Channel Separation modulation Channel Channel Separation Output power (dbm) Low (UHF) 25 KHz 46.97 FM 50W Middle (UHF) 25 KHz 46.95 High (UHF) 25 KHz 46.96
6.2 CONDUCTED SPURIOUS EMISSION IN TRANSMIT MODE Page 10 of 52 LIMIT EN 301 783-1 [1], clause 5.2.3, table 4: For UHF/VHF the rated output power is 50W, -(43+10*log(PEP))= -60 dbc, refer to table 4, the limit for UHF/VHF should be: -50dBc (-3dBm) below 30MHz, and -60dBc (-13dBm) above 30MHz. MEASUREMENT EQUIPMENT USED Equipment Name Manufacture Model No. Dul.Date spectrum analyzer Agilent E4440A 2015-07-17 Signal generator Aglient E4421B 2015-07-17 Remark: Each piece of equipment is scheduled for calibration once a year.
TEST CONFIGURATION Page 11 of 52 Note: The impedance of attenuator is 50ohm. TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.2.2.1 for the measurement method. TEST RESULTS Note: 1. The EUT have been tested under DC 13.8V. 2. Only result the worst case in this part.
VHF TEST RESULT TEST RESULT OF12.5KHZ CHANNEL SEPARATION Middle channel, 9KHz-150MHz Page 12 of 52 Middle channel, 150KHz-30MHz
Middle channel, 30MHz 1GHz Page 13 of 52 Middle channel, 1GHz 12.75GHz
UHF TEST RESULT TEST RESULT OF12.5KHZ CHANNEL SEPARATION Middle channel, 9KHz-150MHz Page 14 of 52 Middle channel, 150KHz-30MHz
Middle channel, 30MHz 1GHz Page 15 of 52 Middle channel, 1GHz 12.75GHz
Page 16 of 52 6.3 CONDUCTED SPURIOUS EMISSION IN RECEIVE OR TRANSIMIT STANDBY MODE LIMIT EN 301 783-1 [1], clause 5.2.3, table 5: MEASUREMENT EQUIPMENT USED Equipment Name Manufacture Model No. Dul.Date spectrum analyzer Agilent E4440A 2015-07-17 H&T Chamber EXPERY TN-400 2015-07-17 Signal generator Agilent E4421B 2015-07-17 Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION
TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. Page 17 of 52 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.2.2.1 for the measurement method. Note: 3. The EUT have been tested under DC 13.8V. 4. Only result the worst case in this part.
VHF TEST RESULT TEST RESULT OF 12.5KHZ CHANNEL SEPARATION Middle channel, 9KHz-150MHz Page 18 of 52 Middle channel, 150KHz-30MHz
Middle channel, 30MHZ-1GHz Page 19 of 52 Middle channel, 1GHz-12.75GHz
UHF TEST RESULT TEST RESULT OF 12.5 KHz CHANNEL SEPARATION Middle channel, 9 KHz-150 MHz Page 20 of 52 Middle channel, 150 KHz-30 MHz
Middle channel, 30MHZ-1GHz Page 21 of 52 Middle channel, 1GHz-12.75GHz
6.4 RADIATED SPURIOUS EMISSION ENCLOSURE PORT IN TRANSMIT MODE LIMIT EN 301 783-1 [1], clause 5.2.3, table6: Page 22 of 52 For UHF/VHF the rated output power is 50W, -(43+10*log(PEP))= -60 dbc, refer to table 4, the limit for UHF/VHF should be: -60dBc (-13dBm) above 30MHz. MEASUREMENT EQUIPMENT USED Equipment Name Manufacture Model No. Serial Number Dul.Date Spectrum Analyzer Agilent E4440A N/A 2015-07-17 Amplifier EM EM30180 0607030 2015-07-17 Horn Antenna EM EM-AH-10180 N/A 2015-07-17 Horn Antenna ETS 3117 00034609 2016-03-19 EMI Test Receiver Rohde & Schwarz ESCI N/A 2015-07-17 Bilogical Antenna A.H. Systems Inc. SAS-521-4 N/A 2015-07-17 WIDEBAND REQUENCY ANTENNA SCHWARZBECK VULB9168 492 2016-03-19 Loop Antenna Daze ZN30900N SEL0097 2015-07-17 Isolation Transformer LETEAC LTBK -- 2015-07-17
TEST CONFIGURATION Page 23 of 52 Below 1GHz
Above 1GHz Page 24 of 52 TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.2.2.2 for the measurement method. TEST RESULT Note: 1. The EUT have been tested under DC 13.8V. 2. Only result the worst case in this part. 3. The transmitter shall be modulated with same test signal as used in clause 5.1 and the measurements made over the frequency range 30 MHz to 4 GHz.
Page 25 of 52 RADIATED SPURIOUS EMISSION (worst) @ 144.025 MHz With 12.5 KHz Channel Separation Below 1GHz EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: Transmitting in Middle Channel Temperature: 25 C Polarity: Horizontal Atmosphere Pressure 101.2Kpa No. Frequency Reading(dbuV) SG Cable Ant Emission Power Loss Gain Level Limit Margin (MHz) (dbuv) (dbm) (db) dbi (dbm) (dbm) (db) 1 288.05 28.53-66.67 0.21 4.4-62.06-13 -49.08 2 431.93 17.86-77.34 0.27 5.2-71.87-13 -58.87 3 576.06 14.73-80.47 0.36 4.6-75.51-13 -62.51 Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power Limit
Page 26 of 52 EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: Transmitting in Middle Channel Temperature: 25 C Polarity: Vertical Atmosphere Pressure 101.2Kpa No. Frequency Reading(dbu V) SG Power Cable Loss Ant Gain Emission Level Limit Margin (MHz) (dbuv) (dbm) (db) dbi (dbm) (dbm) (db) 1 288.05 31.89-63.31 0.26 4.3-58.75-13 -45.75 2 432.05 19.26-75.94 0.31 5.0-70.63-13 -57.63 3 576.23 14.52-80.68 0.38 4.7-75.6-13 -62.60 Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power - Limit
Above 1GHz Page 27 of 52 EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: Transmitting in Middle Channel Temperature: 25 C Polarity: Horizontal Atmosphere Pressure 101.2Kpa No. Frequency Reading(dbuV) Substitution Power Factor (MHz) (dbuv) (dbuv/m) (db) 1 2466.667 44.79-26.31-12.26 2 3650.000 45.12-25.42-11.35 Measurement Power Limit Margin (dbm) (dbm) (db) -38.57-13 -25.57-36.77-13 -23.77 Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power - Limit
Page 28 of 52 EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: Transmitting in Middle Channel Temperature: 25 C Polarity: Vertical Atmosphere Pressure 101.2Kpa No. Frequency Reading(dbuV) Substitution Power Factor (MHz) (dbuv) (dbuv/m) (db) 1 1391.667 44.69-28.24-12.95 2 2858.333 43.98-25.13-11.48 Measurement Power Limit Margin (dbm) (dbm) (db) -41.19-13 -28.19-36.61-13 -23.61
6.5 RADIATED SPURIOUS EMISSION ENCLOSURE PORT IN RECEIVE OR STANDBY MODE LIMIT EN 301 783-1 [1], clause 5.2.3,table7: Page 29 of 52 MEASUREMENT EQUIPMENT USED The same with measurement equipment used of section 6.3 TEST CONFIGURATION The same with test configuration of section 6.3 TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.2.2.2 for the measurement method. TEST RESULTS Note: 1. The EUT have been tested under DC 13.8V. 2. Only result the worst case in this part.
VHF TEST RESULT TEST RESULT OF 12.5KHZ CHANNEL SEPARATION Below 1G Page 30 of 52 EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: idle mode Temperature: 25 C Polarity: Horizontal Atmosphere Pressure 101.2Kpa No. FrequencyReading(dbuV) SG Power Cable Loss Ant Gain Emission Level Limit Margin (MHz) (dbuv) (dbm) (db) dbi 1 104.37 19.79-75.41 0.4 4.6 2 204.60 19.25-75.95 0.2 2.4 3 571.58 8.26-86.94 0.1 1.7 (dbm) (dbm) (db) -71.21-57 -14.21-73.75-57 -16.75-85.34-57 -28.34 Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power Limit
Page 31 of 52 EUT: VR-6600PRO Voltage: DC 13.8V Test Mode: idle mode Temperature: 25 C Polarity: Vertical Atmosphere Pressure 101.2Kpa No. FrequencyReading(dbuV) SG Power Cable Loss Ant Gain Emission Level Limit Margin (MHz) (dbuv) (dbm) (db) dbi 1 97.90 20.42-74.78 0.2 0.1 2 178.73 19.53-75.67 0.3 1.7 3 581.28 9-86.2 1.2 4.3 (dbm) (dbm) (db) -74.88-57 -17.88-74.27-57 -17.27-83.1-57 -26.10 Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power Limit
Page 32 of 52 Above 1G Frequency (MHz) Reading level (dbuv) Antenna Polarizatio n S.G. Cable loss Ant.Gai n Emission level Limit Margin (dbm) (db) (db) (dbm) (dbm) (db) Above 1 GHz -- V -- -- -- -- -- Above 1 GHz -- H -- -- -- -- -- At least 20 db down than the limit Remark: (1) Emission Level (dbm) = SG O/P-Cable + Ant Gain (2) Measuring frequencies from 1 MHz to the 6GHz. (3) Data of measurement within this frequency range shown -- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured.
6.6 CONDUCTED RF IMMUNITY Page 33 of 52 LIMIT REFER TO 301 783-1 SUBPART 5.3.3 Application of the test signal shall not cause the demodulated receiver output to: Be reduced to less than 12 db SINAD for analogue speech equipment; or Be reduced to less than 80 % of the original data throughput for non-speech equipment; or Be degraded to a level declared by the manufacturer as appropriate for the type of signal conveyed. MEASUREMENT EQUIPMENT USED Name of Equipment Manufacturer Model Serial Number Calibration Due Communication Test Set HP HP8920B US35010135 2015-07-17 Signal Generator R&S SMT03 100059 2015-07-17 Signal Generator Agilent E4421B LR114196 2015-07-17 TEST CONFIGURATION Signal Generator 1 Signal Generator 2 Communication Tester Combination Network (EUT) TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.3.2.1 for the measurement method.
Signal of signal generator 1: Page 34 of 52 Signal of signal generator 2: TEST RESULTS Note: 1. The EUT have been tested under DC 13.8V. 2. Only result the worst case in the part.
VHF TEST RESULT RESULT OF DC 13.8V POWER Page 35 of 52 Frequency Modulation Channel SINAD 150KHz-30MHz 30MHz to 1GHz FM FM Low(144.025MHZ) 18.47 Middle(145 MHZ) 18.66 High(145.975 MHZ) 17.67 Low(144.025MHZ) 18.72 Middle(145 MHZ) 17.45 High(145.975 MHZ) 17.64 UHF TEST RESULT RESULT OF DC 13.8V POWER Frequency Modulation Channel SINAD Low(430.025MHZ) 18.54 150KHz-30MHz FM Middle(435 MHZ) 16.93 High(439.975 MHZ) 18.75 Low(430.025MHZ) 17.96 30MHz to 1GHz FM Middle(435 MHZ) 18.22 High(439.975 MHZ) 17.99
APPENDIX 1: PHOTOGRAPHS OF TEST SETUP RADIATED SPURIOUS EMISSION TEST SETUP Page 36 of 52
APPENDIX 2: PHOTOGRAPHS OF EUT TOTAL VIEW OF EUT Page 37 of 52 TOP VIEW OF EUT
BOTTOM VIEW OF EUT Page 38 of 52 FRONT VIEW OF EUT
BACK VIEW OF EUT Page 39 of 52 LEFT VIEW OF EUT
RIGHT VIEW OF EUT Page 40 of 52 TOP VIEW OF ANCILLARY EQUIPMENT
BOTTOM VIEW OF ANCILLARY EQUIPMENT Page 41 of 52 FRONT VIEW OF ANCILLARY EQUIPMENT
BACK VIEW OF ANCILLARY EQUIPMENT Page 42 of 52 LEFT VIEW OF ANCILLARY EQUIPMENT
RIGHT VIEW OF ANCILLARY EQUIPMENT Page 43 of 52 OPEN VIEW-1 OF EUT
Page 44 of 52 OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT
INTERNAL VIEW-1 OF EUT Page 45 of 52 INTERNAL VIEW-2 OF EUT
Page 46 of 52 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT
INTERNAL VIEW-5 OF EUT Page 47 of 52 INTERNAL VIEW-6 OF EUT
INTERNAL VIEW-7 OF EUT Page 48 of 52 INTERNAL VIEW-8 OF EUT
INTERNAL VIEW-9 OF EUT Page 49 of 52 INTERNAL VIEW-10 OF EUT
INTERNAL VIEW-11 OF EUT Page 50 of 52 INTERNAL VIEW-12 OF EUT
INTERNAL VIEW-13 OF EUT Page 51 of 52 INTERNAL VIEW-14 OF EUT
INTERNAL VIEW-15 OF EUT Page 52 of 52 ---END OF REPORT---