Wireless light & temperature New Product Temperature & Light Sensors powered by Beanair Low cost & small package Ultra-low Consumption No need of calibration IEEE 802.15.4 Wireless Stack Very easy to install Two versions of probe available Applications Technical Building Management Cold chain traceability Medical lab & white room Solar Panels Monitoring Transport Air-conditionning System (HVAC) Main Features High & standard accuracy silicon temperature Light measurement range: 0,1 to 40000 Lux Ultra-low power consumption technology IEEE 802.15.4 : Current consumption in idle mode < 15 ua with a maximum autonomy of 7 years Radio range : 30 m to 150 m (L.O.S) «Plug and Play» installation : requires no knowledge of wireless technology No need of calibration (temperature ) Temperature measurement range: -50 C to +150 C or 10 c to +60 C Very small (55 mm x 53 mm x 35 mm) & watertight enclosure (IP65) Entirely autonomous system : powered by Lithiumthionyl chloride primary battery 80
Telemetry on a solar pannels farm The BeanDevice allows a real-time energy performance evaluation of your solar pannels farm. The sunshine and temperature measurements are transmitted by our wireless network coordinator, the BeanGateway, either to your local server (through the BeanScape, our supervision and control monitor), or through a Web site (Remote Web Server OneSense powered by our partner Vertical M2M). The use of the BeanDevice allows the monitoring of the temperature and the sunshine inside greenhouses. The BeanDevice is ecological and highly sustainable. The entire wireless network developped by BeanAir is completely autonomous and energy-saving thanks to an ultra-low consumption technology. The BeanDevice is small -sized and unintrusive. Sunshine and temperature monitoring in greenhouses 81
Thanks to the BeanDevice, you are now able to supervise, and trace the state of your containers. The light can send an alarm when a door is opened/closed on a container. Temperature traceability in containers Geo-location GPS Technical Building Management The BeanDevice helps quickly identifying the sources of energy savings and deficiencies within your building. The BeanDevice is fast and easy to install, as a result you will speed up your installation time and speed up your measurement campaigns. 82
Product reference N- Number of temperature probe : - 1 : one probe BND-SUNT -NCH ST CL-WP ST Temperature Sensor accuracy - HA: high accuracy - CL Cable length WP Wireless Protocol - IEEE : IEEE 802.15.4 (2006) - 0: Sensor probe is integrated in its case - 15: 15 cm cable length - 80: 80 cm cable length - 150: 150 cm cable length Measurement range Photo technology Accuracy Temperature Characteristics Ambient Light Sensor Specifications 0,1 to 40000 Lux Automatically Rejects 50/60-Hz Lighting Silicon photodiodes 3% @25 C 0.1% C Temperature specifications Temperature Sensor technology silicon temperature probe Probe watertightness : IP67 Mechanical assembly type : steel tube Measurement range Measurement accuracy HA: high accuracy HA: high accuracy - 50 C to +150 C for a probe separated from its case - 10 C to +60 C +/- 0.2 C between -10 C and +5 C +/- 0.2 C between +5 C and +45 C +/- 0.2 C between +45 C and +60 C +/- 0.3 C between -10 C and +60 C +/- (0.3 + 0.012(T-60)) C between +60 C and +150 C +/- (0.3-0.012(T+10)) C between -50 C and -10 C HA: high accuracy 0.0034 C Sensor resolution 0.1 C 83
RF Specifications Wireless Protocol Stack IEEE 802.15.4 (2006 version) WSN Topology Point-to-Point / Star Encryption AES 128 bits (AES integrated coprocessor) Data rate 250 Kbits/s RF Characteristics ISM 2.4GHz 16 Channels. Antenna diversity architecture designed by Beanair TX Power -7 dbm to +18 dbm Receiver Sensitivity -95,5 dbm to -104 dbm Radio Range 30 m to 100 m (L.O.S) Antenna Ceramic Antenna 2 dbi -V.S.W.R: 2 :1 Over-the-air configuration (OTAC) parameters Data Acquisition mode Alarm Threshold Low Duty Cycle Data Acquisition (LDCDA) Mode: 1s to 24 hour Alarm mode: the measured value is transmitted by radio whenever an alarm threshold (fixed by the user) is detected (4 alarm threshold levels High/Low). 2 high levels alarms & 2 low levels alarms Power Mode System on «Idle» or «Active» TX Power -7 dbm / -1 dbm / 5 dbm / 11 dbm / 15 dbm / 18 dbm Others specifications During data acquisition : 20 to 30 ma Current consumption During Radio transmission : 40 ma @ 5dBm, 70 ma @ 18 dbm During Idle : < 15 ua Operating Temperature Industrial temperature : -40 C to +85 C Enclosure Norms Included non-rechargeable battery ABS, Watertight IP65 Fire Protection : ULV94 Enclosure dimensions : 55 mm x 53 mm x 35 mm Weight (battery included): 90g CE Labelling Directive R&TTE (Radio) ETSI EN 300 328 ROHS - Directive 2002/95/EC Lithium-thionyl chloride battery with 1350 mah capacity Power-supply bloc (Option) Wall plug-in, Switchmode power Supply 12V @ 1,25A Choose an ultra low power wireless RF Transmission in minutes Every 2 minutes Every 5 minutes Every 10 minutes Autonomy in month 22 months 51 months 102 months 84