Installation instructions, accessories Instruction No 30756561 Version 1.1 5 Part. No. 30756181, 30756569 TV receiver, digital Volvo Car Corporation TV receiver, digital- 30756561 - V1.1 Page 1 / 36
Equipment A0000162 A0000165 IMG-239981 IMG-239664 IMG-317204 Page 2 / 36
IMG-213320 Page 3 / 36
INTRODUCTION Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer. Note! When installing Digital TV-receiver on car with existing RSEsystem, start by changing the cable harness for the tunnel console. See installation instructions Multimedia monitor with DVD, Dual screen. 1 Remove the right front seat mounting's panel of the second row's right seat by pressing down the pawl (1) on top and pulling it forward. Remove the screw underneath. R8504171 Page 4 / 36
2 Remove the panel for the front seat mountings of the second row's right seat/centre seat by pressing down the pawls (1) on top and pulling the panel forward. Remove the screw for the right seat. IMG-318763 3 Fold down the backrest. Remove the seat links and bolts. Lift out the seat. Note! This step should be performed carefully to avoid damaging interior or door panel. IMG-242247 Page 5 / 36
4 Carefully pry loose and remove the panel located over the joint between the door sills on the right side. IMG-317225 5 Loosen the upper part of the sill moulding at the rear edge and loosen the seat belt from the end-fitting. The belt is loosened by carefully pressing with a weatherstrip tool on the lock lug so that it releases from the end-fitting. IMG-317226 Page 6 / 36
6 Pull the sill protection upward until the three clips release. Angle out the sill protection from the B-pillar panel. IMG-317227 7 Insert a screwdriver through the hole (1) on the right seat's left rear seat link and press in the pawl. Move the link backwards by prying with a screwdriver between the seat rail and the link. IMG-242244 Page 7 / 36
8 Remove the rear roof panel covers and the screws beneath them. Carefully pry away the panel at the rear edge with a plastic weatherstrip tool. Pull the rear edge of the panel downwards until the four clips on the top have released. Unplug the connector for the lighting. Pull the panel backwards to release it. R8504201 9 Pull loose the rubber strip at the trailing edge of the left door opening, directly opposite the C-pillar panel. Carefully pry off the left C-post panel by the sides at the top with a plastic weatherstrip tool. Then pull until the three clips on the inside release. Do not damage the headlining or the panel. If a headphone socket is mounted, disconnect the connector to such. Remove the panel by pulling upwards slightly and unhooking it from the side panel. IMG-317228 Page 8 / 36
10 Carefully loosen the pillar panel. Start at the top and continue downwards until the three clips on the inside have released. Remove the connector on the D-pillar panel. Cars with D-pillar speakers have the connector located on the speaker. Remove the panel by pulling upwards slightly and unhooking it from the side panel. IMG-317304 11 Applies to cars with two rows of seats Open up the floor hatch (1). If the floor hatch is equipped with a grocery bag holder on the underside, then it is fastened with a strap on both sides of the storage box. Then these shall be loosened by first removing the storage box under the floor hatch and then removing the floor hatch by almost closing it and pulling it backwards out of its attachments. Applies to cars with three rows of seats and integrated carrier bag holder on the underside of the floor hatch. Fold up the floor hatch (1). Loosen the two straps on the underlying panel. Lift up the trailing edge of the panel, fold the floor hatch back towards the panel and lift out the floor hatch and panel. IMG-242240 Applies to cars with three rows of seats without an integrated carrier bag holder. Open the floor hatch (1) at the trailing edge and lift it out. Page 9 / 36
12 Remove the three screws on the battery holder and lift it out. Remove the battery cover. R3100130 13 Remove both covers on the floor. IMG-242241 Page 10 / 36
14 Remove both panels. IMG-242242 15 Fold out the load lashing eye on the right side. Take a scriber or special tool part no.9995919 and insert the angled point in the hole in the top edge of the cover. Twist the scriber so it grips the rear of the cover (1) and pull it loose. This should be performed on both the front and rear load lashing eyes. R8504313 Page 11 / 36
16 Applies to cars with two rows of seats Remove the screws (2) on the load securing eyelets. Remove the cover (3), by prying off using a weatherstrip tool or a small screw driver. Remove the screws (4). Remove the panel by pulling it out slightly at the top edge so that the clips on the inside release. Then pull it straight up. Unplug the connector for the 12V socket. IMG-317343 17 Applies to cars with three rows of seats Fold up the left-hand seat in the third row of seats. Remove the screws (2) on the load securing eyelets. Remove the covers (3) by prying with a weatherstrip tool or a small screwdriver. Remove the screws (4). Remove the panel by pulling it out slightly at the top edge so that the clips on the inside release. Then pull it straight up. Unplug the connector for the 12V socket. IMG-317363 Page 12 / 36
18 Remove the two clips. IMG-317383 19 Install plastic nuts in the holes where the clips were located, as shown. Note! Turn the plastic nut so that it faces the right way. IMG-317384 Page 13 / 36
20 Remove the cover panel under the tail lamps on the right and left sides by carefully prying them loose using a weatherstrip tool. R8600873 21 Loosen the rear fog light at the front with a weatherstrip tool. Done on both sides. R3501466 Page 14 / 36
22 Remove the tail light by removing the two nuts and pulling them back. Done on both sides. R3501459 23 Take antenna and holder from the kit. Place the antenna in the casing and the cable in the slot. Snap together the casing's top and bottom parts. Done twice. IMG-317470 Page 15 / 36
24 Install the holders on the casing. Repeat the on the other casing. IMG-317472 25 Get antenna for left side (long cable) and unplug the grey connector. Insert casing with antenna in the outlet for fog lights. Press on the casing's holder on the plastic flange at the bottom edge of the plastic console. IMG-317473 Page 16 / 36
26 Route the cable up through the bumper so that it comes out at the top of the plastic console. IMG-317474 27 Remove the top part of the foam tape that covers the hole. IMG-317475 Page 17 / 36
28 Get the rubber bushing from the kit and open it up with expander pliers. Insert the antenna cable. Route the cable so that the length of the cable between the bushing and the top of the plastic console is 250 mm. Install a strip clamp around the collar on the rubber bushing so that it closes tightly around the cable. Cut off excess strip clamp. IMG-317476 29 Insert the antenna cable through the hole in the body so that it comes out in the passenger compartment. IMG-317477 Page 18 / 36
30 Check that the rubber bushing's flanges close tight against the body hole. IMG-317478 31 Install the strip clamp on the sheet metal flange. Clamp down the antenna cable in the clamp. Cut off any excess strip clamp. Carry out on both sides. IMG-317479 Page 19 / 36
32 Connect the removed antenna cable. Insert a strip clamp though the connector. Carry out on both sides. IMG-317483 33 Clamp down the connector in existing cable harness (1). Clamp down the cable in existing cable harness with the strip clamp (2). Carry out on both sides. IMG-317484 Page 20 / 36
34 Route the antenna cable along existing cable harness over to the right side through the hole in the polystyrene plastic under the right member. IMG-317551 35 Fasten the cable with strip clamps. IMG-317503 Page 21 / 36
36 Get TV-tuner, console, as well as four screws from the kit. Tighten down the tuner on the console. IMG-317504 37 Take the cable harness from the kit. Plug in the connectors in the order as shown. Note! Tighten the nuts on the antenna cables' contacts as much as possible with your fingers while the black part of the contact is held down. Then tighten the nuts (3) one complete turn with a wrench. IMG-317506 Page 22 / 36
38 Install fuse holders in the holes on the inside of the console. IMG-317507 39 Fasten the console with screws from the kit. Note! Cut away a piece of insulation for the lower attachment. IMG-317508 Page 23 / 36
40 Install the strip clamp on the tuner's sheet metal flange. Clamp down the antenna cables. IMG-317509 41 Install the strip clamp on the tuner's sheet metal flange. Clamp down the cable harness. IMG-317883 Page 24 / 36
42 Fold aside the noise absorbent so that the sheet metal flange is visible. Install the strip clamp on the sheet metal flange. Clamp down both cables (1). Fold back the noise absorbent. Clamp down both antenna cables and excess cable in existing cable harness. IMG-317510 43 Route the cable harness along the wheel housing down to the belt anchor. Fasten with strip clamps. IMG-317511 Page 25 / 36
44 Fasten the cable harness in the belt anchor with strip clamp. IMG-317512 45 Fold up the floor mat. IMG-317513 Page 26 / 36
46 Place the cable harness between polystyrene plastic and body under the floor mat so that it runs along the floor sides on to the tunnel. Make sure that the yellow marking on the cable harness is placed on the cable harness by the mat's edge at the tunnel. IMG-317514 47 Install the strip clamp on the sheet metal flange. Fasten the cable harness. IMG-317523 Page 27 / 36
48 Install the strip clamp around the cable harness by the yellow marking and press to fasten the clamp on the parking brake console's flange. IMG-317524 49 Get the side panel. Cut away the strip clamp and remove the cover. IMG-317525 Page 28 / 36
50 Remove the belt holder and rough up the fabric where the holder has been installed. IMG-317526 51 Remove the rear cup holder. IMG-317528 Page 29 / 36
52A Illustrations A and B Measure and mark out on the inside of the side panel as shown. Saw according to markings. 52B IMG-317530 IMG-317531 53 File down the edges. IMG-317532 Page 30 / 36
54 Saw by the side panel's rear cup holder as shown. IMG-317533 55 File down the edges. IMG-317534 Page 31 / 36
56 Take the casing from the kit. Mark out the middle on the three flanges with a scribe. Drill using a 3.5 mm bit. IMG-317536 57 Fasten tape as shown. IMG-317543 Page 32 / 36
58 Temporarily install the casing. IMG-317544 59 Mark the casing's three drilled holes on the tape. Remove the cover. IMG-317545 Page 33 / 36
60 Punch holes in the markings and through the panel with an awl or scribe. Remove the tape. Drill holes using a 7 mm bit. IMG-317546 61 Install the casing. Check from the rear that the four catches have engaged. IMG-317547 Page 34 / 36
62 Loosen the insulation at the top and on the sides. Note! The insulation shall be left in place at the bottom. IMG-317548 63 Tighten down the casing with three screws PF5x14 and three washers. IMG-317549 Page 35 / 36
64 Fold back the insulation and fasten it with three pieces of tape. Reinstall the side panel. Reinstall removed parts in reverse order. Tightening torque seat screws 40 Nm and load lashing eyes 25 Nm. Continue according to installation instruction Multimedia monitor with DVD, Dual Screen. IMG-317550 Page 36 / 36