eburring and chamfering for smooth finishing operations
2 Chamfering in smallest dimensions CrazyMill Frontchamfer matches ideally the existing cutting tool program of Mikron Tool. Available from diameter 1, this chamfer milling cutter is suitable for machining smallest workpieces and can reach practically all angles and corners. The high number of teeth to depending on diameter allows high feeds. The positive cutting geometry guarantees an excellent surface quality. The features: Carbide alloy All tools are coated iameters from 1 to Chamfer of to teeth Suitable for all materials Item number z l (h) FC.0010090.1 0. 1 0 FC.0020090.1 0. 2 0 FC.1000090.1 1-0 FC.100090.1 1. - 0 FC.2000090.1 2-0 Upon request: special executions in particular dimensions, number of teeth or different chamfer angle definite geometry for the machining of hardened steel over HRC Executions 1 an 0 l Executions to FC.0020090.1
Guidelines for cutting parameters Materials to be machined Examples Cutting speed vc m/min mill Ø 1.0-2.0 Feed f z in /revolution per tooth mill Ø.0 -.0 Ck, 1MnCr, 20MnCr up to 120 0.01-0.0 0.0-0.0 Tool Steels 100Cr, 90MnCrV8 0.01-0.0 0.02-0.0 high-alloy G-X 100 CrMoV 1, X210CrW12, S 18-1-2-10 up to 80 0.01-0.02 0.01-0.0 Hardened Steel >0HRC 90MnCrV8, X0CrV-1 up to 0 0.01-0.02 0.01-0.0 ferritique X17CrNi1-2, XCrMo 17-1, X20Cr1, G-X10CrSi29 up to 0 0.01-0.02 0.02-0.0 austenitique XCrNi 18-10, X10CrNiS 18-9 up to 0 0.01-0.02 0.02-0.0 Titanium and Titanium alloy Ti. Gr2, Ti. Gr up to 0 0.01-0.02 0.02-0.0 Cast iron GG 20 - GGG 0 GGG 0 - GGG GTW/GTS up to 0 0.01-0.02 0.01-0.0 easy to machine CuZn9Pb2 0.02-0.0 0.0-0.07 hard to machine Cu, CuZn10, CuZn0, CuNi18Zn20 0.02-0.0 0.0-0.07 Alloys wrought, Magnesium alloys AlSi1, AlSi1 MGMn, AlCuMgPb 0.02-0.0 0.0-0.07 alloys cast 0.02-0.0 0.0-0.07 Gold Silver 0.01-0.0 0.02-0.0 These values are intended to represent approximate ranges. ifferent conditions due to machine, spindle, coolant, etc. can influence the performance. The optimized parameters for each operation should be determined by tests or during the machining process. Important for successful machining: - Mikron Tool recoends simultaneous milling in two steps, thus avoiding secondary burrs. - ue to the high number of teeth 0% higher feeds are allowed.
Back chamfering without re-clamping With CrazyMill Backchamfer no work piece turnover and re-clamping is necessary to machine hard-to-reach holes or edges on the back side of a work-piece. This chamfer mill allows miniature machining, starting from holes or slots as small as 0.. The high number of teeth guarantees an excellent surface quality. Main applications for this new milling cutter are found where small machining operations with very high quality are required, such as med-tech parts, watch industry, automotive, etc. CrazyMill Backchamfer can be used for all metals and is also suitable for tough materials that generate long chips. The features: Carbide alloy All tools are coated iameters from 0. to.7 For hole diameters from 0. Chamfer of to teeth Suitable for all materials imensions matched to Crazyrill program Usable length x Item number z (h) Max. chamfer width (f) BC.00090.1 0.22 0. 1. 0.20 0.0 BC.00090.1 0. 0. 1.9 0.2 0.0 BC.00090.1 0. 0. 2. 0. 0.0 BC.0090090.1 0. 0.9.7 0.0 0.07 BC.010090.1 0.9 1.. 0.90 0.1 BC.0190090.1 1.0 1.9 7.8 1.00 0.1 BC.0290090.1 2.10 2.9 10.8 1.0 0 0.2 BC.0090.1 2..7 1.0 0 0. BC.0090.1.0.7 17. 0. BC.0090.1.00.7 20 0. Usable length x Item number z (h) Max. chamfer width (f) BC.00090.1 0.22 0. 2. 0.20 0 0.0 BC.00090.1 0. 0..0 0.2 0 0.0 BC.00090.1 0. 0..2 0. 0 0.0 BC.0090090.1 0. 0.9.0 0.0 0 0.07 BC.010090.1 0.9 1. 9.0 0.90 0 0.1 BC.0190090.1 1.0 1.9 12.0 1.00 0 0.1 BC.0290090.1 2.10 2.9 18.0 1.0 0.2 BC.0090.1 2..7 2.0 0. BC.0090.1.0.7 0.0 80 0. BC.0090.1.00.7.0 80 0. Upon request: special executions for different lengths, dimensions, number of teeth or different chamfer angle definite geometry for the machining of hardened steel over HRC
Guidelines for cutting parameters Materials to be machined Examples Cutting speed vc m/min Ø 0. - 1.90 Feed f z in /revolution per tooth Ø 2.90 -. Ck, 1MnCr, 20MnCr up to 120 up to 0.0 Tool Steels 100Cr, 90MnCrV8 high-alloy G-X 100 CrMoV 1, X210CrW12, S 18-1-2-10 up to 80 up to 0.01 Hardened Steel >0HRC 90MnCrV8, X0CrV-1 up to 0 up to 0.01 ferritique X17CrNi1-2, XCrMo 17-1, X20Cr1, G-X10CrSi29 up to 0 up to 0.01 austenitique XCrNi 18-10, X10CrNiS 18-9 up to 0 up to 0.01 Titanium and Titanium alloy Ti. Gr2, Ti. Gr up to 0 Cast iron GG 20 - GGG 0 GGG 0 - GGG GTW/GTS up to 0 up to 0.01 easy to machine CuZn9Pb2 up to 0.0 hard to machine Cu, CuZn10, CuZn0, CuNi18Zn20 up to 0.0 Alloys wrought, Magnesium alloys AlSi1, AlSi1 MGMn, AlCuMgPb up to 0.0 alloys cast G-AlSi9Cu, G-AlSi12, G-AlSi10Mg up to 0.0 Gold Silver These values are intended to represent approximate ranges. ifferent conditions due to machine, spindle, coolant, etc. can influence the performance. The optimized parameters for each operation should be determined by tests or during the machining process. Important for successful machining: - Mikron Tool recoends conventional milling for avoiding secondary burrs. - Ideal are two milling passages - For small diameters, the quality and above all the straightness of the hole are of utmost importance. - Mikron Tool recoends to drill a pilot hole with Crazyrill Pilot and a precise drilling with Crazyrill. - Tangential approach prevents a vibration and a subsequent breakage of the milling tool.
One clamping for front and back side chamfering With a single tool front and back side chamfering of edges and hard-to-reach spots: CrazyMill oublechamfer allows it also in a smallest diameter range - for diameters from Ø 1. The high number of teeth guarantees an excellent surface quality. Main applications for this new milling cutter are found where small machining operations with very high quality are required, such as med-tech parts, watch industry, automotive, etc. The features: Carbide alloy All tools are coated iameters from 0.9 to.7 Chamfer of resp. to teeth Suitable for all materials Usable length x Item number z (h) Max. chamfer width (f) C.0090090.1 0. 0.9 2.7 0. 0.22 C.010090.1 0.7 1..2 0.7 0. C.0180090.1 0.9 1.8. 0.9 0. C.0280090.1 1. 2.8 8. 1. 0 0. C.0090.1 1.8.7 11.1 1.8 0 0.92 C.0090.1 2..7 1.1 2. 1.17 C.0090.1 2.8.7 17.1 2.8 1.2 Usable length x Item number z (h) Max. chamfer width (f) C.0090090.1 0. 0.9. 0. 0 0.18 C.010090.1 0.8 1. 8. 0. 0 0.28 C.0180090.1 1.08 1.8 10.8 0.72 0 0. C.0280090.1 1.8 2.8 1.8 1.12 0 0. C.0090.1 2.22.7 22.2 1.8 0 0.7 C.0090.1 2.82.7 28.2 1.88 80 0.9 C.0090.1.2.7.2 2.28 80 1.1 Upon request: special executions for different lengths, dimensions, number of teeth or different chamfer angle f
7 Guidelines for cutting parameters Materials to be machined Examples Cutting speed vc m/min Ø 0. - 1.90 Feed f z in /revolution per tooth Ø 2.90 -. Ck, 1MnCr, 20MnCr up to 120 up to 0.0 Tool Steels 100Cr, 90MnCrV8 high-alloy G-X 100 CrMoV 1, X210CrW12, S 18-1-2-10 up to 80 up to 0.01 Hardened Steel >0HRC 90MnCrV8, X0CrV-1 up to 0 up to 0.01 ferritique X17CrNi1-2, XCrMo 17-1, X20Cr1, G-X10CrSi29 up to 0 up to 0.01 austenitique XCrNi 18-10, X10CrNiS 18-9 up to 0 up to 0.01 Titanium and Titanium alloy Ti. Gr2, Ti. Gr up to 0 Cast iron GG 20 - GGG 0 GGG 0 - GGG GTW/GTS up to 0 up to 0.01 easy to machine CuZn9Pb2 up to 0.0 hard to machine Cu, CuZn10, CuZn0, CuNi18Zn20 up to 0.0 Alloys wrought, Magnesium alloys AlSi1, AlSi1 MGMn, AlCuMgPb up to 0.0 alloys cast G-AlSi9Cu, G-AlSi12, G-AlSi10Mg up to 0.0 Gold Silver These values are intended to represent approximate ranges. ifferent conditions due to machine, spindle, coolant, etc. can influence the performance. The optimized parameters for each operation should be determined by tests or during the machining process. Important: for successful machining Mikron Tool recoends: - Conventional milling - Ideal are two milling passages for burr free edges and a good surface quality - Especially for back side chamfering: - For small diameters, the quality and above all the straightness of the hole are of utmost importance. Mikron Tool recoends to drill a pilot hole with Crazyrill Pilot and a precise drilling with Crazyrill. - Mainly for long versions, tangential approach prevents a vibration and a subsequent breakage of the milling tool.
8 For highest requirements: all in one tool This universal radius chamfer tool has a big cutting area of 00. Thus it is ideal for front and backside deburring as well as for all kind of inside and outside contours, intersections of drillings and millings. ue to its specific positive cutting geometry it also removes tenacious and ductile burrs and avoids the forming of new, secondary burrs. The extra long execution also permits machining on hard-to-reach spots (inclined hole exits etc.). The features: Usable cutting range 00 For front and backside deburring Specific positive cutting geometry Carbide alloy All tools are coated Suitable for all metals Item number R (-0.02) z (0-0,0) (h) RC.00100.1 0.0 0.0 1.0.0 0 RC.0010.1 0.7 0.7 1.. 0 RC.00200.1 1.00 1.00 2.0.0 8 0 RC.0020.1 1.2 1.2 2. 7. 10 0 RC.0000.1 1.0 1.0.0 9.0 12 0 RC.0000.1.0 12.0 1 RC.0000.1.00.00.0 18.0 2 Upon request: Special execution for lengths and other dimensions. 1 R State-of-the art: The specific positive cutting geometry: removes also tenacious and ductile burrs. The big usable cutting area of 00 : allows an universal usage for front and backside deburring and chamfering.
9 Guidelines for cutting parameters Materials to be machined Examples Cutting speed vc m/min Ø 1-2 Feed f z in /revolution per tooth Ø - Ck, 1MnCr, 20MnCr up to 120 up to 0.0 Tool Steels 100Cr, 90MnCrV8 high-alloy G-X 100 CrMoV 1, X210CrW12, S 18-1-2-10 up to 80 up to 0.01 Hardened Steel >0HRC 90MnCrV8, X0CrV-1 up to 0 up to 0.01 ferritique X17CrNi1-2, XCrMo 17-1, X20Cr1, G-X10CrSi29 up to 0 up to 0.01 austenitique XCrNi 18-10, X10CrNiS 18-9 up to 0 up to 0.01 Titanium and Titanium alloy Ti. Gr2, Ti. Gr up to 0 Cast iron GG 20 - GGG 0 GGG 0 - GGG GTW/GTS up to 0 up to 0.01 easy to machine CuZn9Pb2 up to 0.0 hard to machine Cu, CuZn10, CuZn0, CuNi18Zn20 up to 0.0 Alloys wrought, Magnesium alloys AlSi1, AlSi1 MGMn, AlCuMgPb up to 0.0 alloys cast G-AlSi9Cu, G-AlSi12, G-AlSi10Mg up to 0.0 Gold Silver These values are intended to represent approximate ranges. ifferent conditions due to machine, spindle, coolant, etc. can influence the performance. The optimized parameters for each operation should be determined by tests or during the machining process. Important for successful machining: - Mikron Tool recoends conventional milling for avoiding secondary burrs.
10 Flexibility with CrazyMill: the universal deburring tool For difficult machining operations, tenacious burrs or hard-to-reach points. Often the individual solution is the most economical one, as it is matched ideally with the work piece and the material to be machined. Mikron Tool develops and manufactures special executions of milling tools for any application. Examples: front and backside chamfering chamfer tool diameter 2 reachable depth 10 teeth front and backside chamfering chamfer tool diameter 1.8 reachable depth teeth simultaneous front chamfering and back side deburring chamfer diameter drilling depth / border length 2 teeth back side deburring and double chamfering on frontside chamfer diameter.9 teeth multiple chamfer milling cutter x chamfer diameter 7 teeth inside cooling channels ground in shank multiple chamfer milling cutter 10x chamfer diameter 10 teeth
11 Unlimited possibilities for specific applications The CrazyMill chamfer and deburring tools can be used for various applications and for all materials. Special executions guarantee an optimal solution for every machining operation. Examples: Automotive steemncr CrazyMill Radiuschamfer Ø 1. Automotive stee8crni18 Special chamfer tool for grooves and backside Ø 1 Automotive Quadruple chamfer milling cutter Ø 8 Medical Engineering CrazyMill Radiuschamfer Ø Pneumatic Multi chamfering milling cutter Ø 8 Watch Industry Chamfering tool for 2 different hole sizes Ø 1 / 2 Appliances Steel Chamfering tool for 2 holes simultaneously Ø
12 Services that complete the concept Engineering and Consulting Mikron Tool advises its customers on the selection of suitable tools with respect to material and geometry, necessary tolerances and ideal operating parameters, and partners with them from the initial trials through mass production. Star-Service With the Star Service (Standard Tool Adjustment & Record Service), Mikron Tool also offers high-performance tools in dimensions outside the standard range. Packaging Practical packaging provides optimum protection for the tool and allows easier, safer handling without the risk of personal injury or tool damage. Recycling Worn tools are taken back by Mikron Tool, and the material is recycled holding true our statement in our environmental certificate. Certifications Mikron Tool is certified to: ISO 9001:2008 for quality ISO 1001:200 for environment OHSAS 18001:2007 for occupational health and safety management.
1 High performance tools from Mikron Tool Crazyrill: for large production lots and materials difficult to machine. Crazyrill is ideally suited for high volume production of precision parts. Crazyrill offers, comparing to standard drills, much higher cutting speeds and feeds. Pilot Pilot Pilot Pilot Twicenter Crosspilot Pilot Twicenter Crosspilot Miqurill: for smaller production lots and a variety of work pieces Mikron Tool standard quality drills Miqurill are the perfect solution for the machining of small to medium batches of parts, guaranteeing at the same time quality and process reliability. Special tools: customer tailored solutions for machining of precision parts eveloped for particular machining operations; special tools guarantee the best conditions for a process-sure, efficient machining of precision parts. Special tools
Your contacts Headquarter and Production: Mikron Tool SA Agno Postfach 0 9 Bioggio Switzerland Tel. +1 91 10 0 00 Fax +1 91 10 0 10 mto@mikron.com Production for Germany and Regrinding EU: Mikron GmbH Rottweil Abteilung Werkzeuge Berner Feld 71 7828 Rottweil Germany Tel. +9 71 80 0 Fax +9 71 80 80 info.mtr@mikron.com North and South America Sales: Mikron Corp. Monroe P.O. Box 28 200 Main Street Monroe, CT 08 USA Tel. +1 20 21 100 Fax +1 20 28 72 o@mikron.com www.mikron.com/tool Information and technical data are liable to changes without prior notification. Mikron is a trademark of Mikron Holding AG, Biel (Switzerland) 1012