FM 357-2 POSITIONING MODULE Function FM 357-2 with FM 357L system firmware 4 measuring circuits for the connection of position-controlled servo axes/stepper drives or external master axis Relationship of axes: Linear, circular interpolation, independent single axes Axis synchronization via coupled motion or curve tables (electronic cam) also with external master Motion control with programmable acceleration and jerk limitation Transformable coordinate systems Operating modes: Jog, incremental, reference-point approach, MDI (Manual Data Input), automatic, automatic single-block Limit switching signals (cam controller) Special emergency stop routines with high-speed restart Program-controlled motion output from the motion program, M instructions Parameterizable programs via user variables Programming in accordance with DIN 66025 with high-level language elements (loops, conditions) Data backup to memory card (optional) Multichannel capability (up to 4 channels can be defined in any combination, 1 channel in the case of FM 357-2H) Page 1210 Mar 2008 Siemens ITS
FM 357-2 with FM 357 LX system firmware As for FM 357-2 with FM 357L system software, plus: Spline interpolation (A-, B-, C spline) for definition of movements via interpolation points High-value gantry functions with rigid compensation control Flexible synchro actions (expanded interrupt routines) Probe analysis without time-delay Programmable overlay of oscillation movement Path-speed-dependent variable control Programmable travel against fixed stop 3 D protection zones FM 357-2 with FM 357 Handling system firmware As for FM 357-2 with FM 357LX system software, plus: Coordinate transformation for jointed-arm, Scara and gantry systems with up to 4 axes Teach-in functions with the HT6 handheld terminal Page 1211 Mar 2008 Siemens ITS
Mode of operation Preparatory steps Load the firmware and parameterization software supplied separately Wizard-supported comparison of machine data with the configuring software integrated in STEP 7 Generation of traversing programs: Generation with the editor of the parameterization software according to DIN 66025 Implementation of coordination and sequence control functions in the STEP 7 user program on the CPU. Standard function blocks simplify this task. Positioning and continuous-path control The FM 357-2 controls the axes independently. Positioning tasks are started via the OP or higher-level programmable controller Human machine interface Using any SIMATIC HMI components; SIMATIC OP7 and OP17 also support direct communication with the FM 357-2. Direct variable access is also possible with ProTool Version 6 and Windows-CE-based operator panels from TP170B upwards. Technical specifications Page 1212 Mar 2008 Siemens ITS
Technical specifications 6ES7 357-4AH01-0AE0 Supply voltage 24 V DC Yes Input current from backplane bus 5 V DC, max. 100 ma Encoder supply 5 V encoder supply 5 V Yes Output current, max. 210 ma 35 m 24 V encoder supply 24 V Yes Output current, max. 300 ma 100 m Power Power consumption, typ. 24 W Memory NC program memory 750 Kibyte Digital inputs Number/binary inputs 18 Functions 4 Bero, 2 probes, 12 for any use Page 1213 Mar 2008 Siemens ITS
Input voltage Rated value, DC 24 V for signal "0" -3 to +5 V for signal "1" 11 to 30 V Input current for signal "0", max. (permissible quiescent 2 ma current) for signal "1", typ. 6 ma; 6 to 30 ma Digital outputs Number/binary outputs 8 Functions 8 for any purpose Output voltage Rated value (DC) 24 V for signal "1", min. UP -3 V Output current for signal "1" permissible range for 0 to 0.5 A; with UPmax 55 C, max. for signal "0" residual current, max. 2 ma Encoder Connectable encoders Incremental encoder (symmetrical) Yes Absolute encoder (SSI) Yes Encoder signals, incremental encoder (symmetrical) Page 1214 Mar 2008 Siemens ITS
Trace mark signals A, nota, B, notb Zero mark signal N, notn Input signal 5 V difference signal (phys. RS 422) Input frequency, max. 1 MHz Encoder signals, absolute encoder (SSI) Input signal 5 V difference signal (phys. RS 422) Data signal DATA, notdata Clock signal CL, notcl Telegram length 13, 21 or 25 bit Clock frequency, max. 1.5 Mbit/s Cable length, shielded, max. 250 m; At max. 187.5 kbit/s Positioning Programmable traverse speed, max. 1 000 m/min Drive interface Signal output I Type 5 V difference signal (phys. RS 422) Function Direction, enable, clock pulse Differential output voltage, min. 2 V; RL = 100 Ohm Differential output voltage for signal "0", 1 V; Io = 20 ma max. Differential output voltage, for signal "1", 3.7 V; Io = -20 ma min. Pulse frequency 750 khz 50 m; 35 m in hybrid mode with servo Page 1215 Mar 2008 Siemens ITS
Signal output II Type Function Load Signal output III Type Function Output voltage Output current Galvanic isolation Galvanic isolation digital inputs Galvanic isolation digital inputs Galvanic isolation digital outputs Galvanic isolation digital outputs Connection method required front connector Dimensions Width axes Controller release (contact), FM-READY output (contact) Drive disconnection for operation via contact relay, Data set ready for link with Emergency STOP 1 A/50 V/30 VA DC Analog output Drive interface for analog drives: setpoint output for drive -10 to +10 V -3 to +3 ma 35 m Yes Yes 1x 40-pin 200 mm Page 1216 Mar 2008 Siemens ITS