Chester - Solid Pine Desk ssembly Instructions- Please keep for future reference 89/600 18/812 Dimensions Width - 120cm Depth - 50cm Height -,cm Important Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call t h e C ustomer Helpline: 056 00 800.
Safety and Care dvice Important Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 2 and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. ssemble the item as close to its final position (in the same room) as possible. ssemble on a soft level surface to avoid damaging the unit or your floor. This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault. The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture. On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time. This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Parts of the assembly will be easier with 2 people. Dispose of all packaging carefully and responsibly. Care and maintenance Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product. void placing the furniture in direct sunlight as this will cause the timber to prematurely age. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. 1 Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels Please check you have all the panels listed below 1 Top panel (120 x 50cm) 2 Right side panel (2,5 x 6,9cm) 5 Right front frame (2,5 x,6cm) Division (2,5 x 5,8cm) Left side panel (2,5 x 5,8cm) 6 Left front frame (2,5 x,6cm) Large back rail x2 (6,1 x 8,5cm) 8 Small back rail (2,5 x,cm) 9 Top front frame (, x,cm) 10 Middle front frame 11 ottom front frame (, x,cm) (, x 8,6cm) 12 Drawer front x2 (6,8 x 26,6cm) 1 Drawer right side x2 1 Drawer left side x2 15 Drawer back x2 (5 x 20 cm) (5 x 20cm) (, x 20cm) 16 Drawer bottom x2 (, x,cm) 1 Side drawer runner x (. x,cm) 18 ack panel (68, x,cm) 2
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 056 00 800. Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. C Wooden dowel x 5 0mm Screw x 52 Drawer handle x 2 D E F Nail x 20 22mm olt x racket x 6 G 16mm Screw x 12 Tools required Phillips screwdriver (medium & large) 2 m Ruler/tape measure Small hammer Eye protection (when using a hammer or glue) Ruler - Use this ruler to help correctly identify the screws 0 5 10 15 20 25 0 5 0 5 50 55 60 65 0 5 80 85 90 95 100 105 110 115 120 125 10 15 10 15 150 155 160 165 10
ssembly Instructions Step 1 (x) 1 09 (2x) 1 11 8 (2x) 2 10 1 (2x) Insert dowels indicated parts. into the Step 2 Fixing runners. ttach side drawer runners 1 to division using screws. ttach side drawer runners 1 to left side panel using screws. 1 1 1 ttach brackets F through pre drilled holes on left side panel and division using screws G where shown. 1 F G G F (x) (x)
ssembly Instructions Step Fixing left front frame to the left side panel (Two people required for an easier assembly). a: 6 Insert left front frame into left side panel through joints. (x) No! 6 Yes! G Note: efore fixing brakets F into place it is important to ensure that the slot and groove of parts and 6 are fully pushed together and lined up correctly at top and bottom. (+) 6 (-) Fix brakets into front frame using screws G. Top Step Fixing right front frame to division. (Two people required for an easier assembly). a: Insert right front frame 5 into division through joints. Note: efore fixing brakets F into place it is important to ensure that the slot and groove of parts and 5 are fully pushed together and lined up correctly at top and bottom. Top (-) 5 No! G Yes! 5 (x) (+) Fix brakets into front frame using screws G. 5
ssembly Instructions Step 5. ttention: ttach small back rail 8, top front frame 9 and bottom front frame 11 to left side panel using screws. Fit middle front frame 10 to left front frame 6. 11 Make sure panels are correctly positioned as shown in the diagram. 8 10 9 Step 6 Fixing the division Two people are required for an easier assembly. Fit division to the assembled part, then fix it using screws. 6
ssembly Instructions Step Fixing top panel Two people are required for an easier assembly. Caution: Carefully lay the top panel on a soft and clean surface to avoid damaging the product. ttach assembled frame to the top panel 1 using screws. Note correct position of parts as shown. 1 Step 8 Fixing back rail. Fit large back rails the right side panel then fix them using screws. 2 to 2
ssembly Instructions Step 9 Two people are required for an easier assembly. Fit back panels to division and right side panel to top panel 1 as shown. Then, fix the parts using screws. 1 Step 10 Fixing back panel. Important: Desk MUST be square when back panel is attached. ttach the back panel 18 using nails D. 18 D 8
ssembly Instructions Step 11 Drawer assembly. a: b: c: a:ttachdrawer sides 1 and 1 to the drawer front 12 usingscrews. b: slide drawer bottom 16 into slots on drawer sides 1 1 16 15 c: attach drawer back 15 using screws. 12 d:using screw E attach the drawer handle C to the drawer front. Repeat step 11 to the other drawer. (2X) d: E E Step 12 C Insert drawers into unit. With the back of the drawers past the front frames, use a hammer to tap dowels in flush to drawer sides. This is a safety catch to stop drawer falling out. ssembly is complete. 9 If you need help or have damaged or missing parts, call t h e rgos Customer Helpline: 056 00 800 or Homebase Customer Helpline: 05 0 8888.