HF/VHF/UHF ALL MODE Transceiver FT-897 Technical Supplement

HF/VHF/UHF ALL MODE Transceiver FT-897 Technical Supplement 2002 VERTEX STANDARD CO., LTD. Printed in Japan. VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. International Division 8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A. YAESU EUROPE B.V. P.O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Introduction This manual provides technical information necessary for servicing the FT-897 HF/VHF/UHF ALL MODE Transceiver. Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-qualified persons to service this equipment may result in permanent damage not covered by the warranty, and may be illegal in some countries. Two PCB layout diagrams are provided for each double-sided circuit board in the Transceiver. Each side of is referred to by the type of the majority of components installed on that side ( leaded or chip-only ). In most cases one side has only chip components, and the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic capacitors, ICs, etc.), or leaded components only. While we believe the technical information in this manual to be correct, VERTEX STANDARD assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. Specifications... 2 Exploded View & Miscellaneous Parts... 4 Block Diagram... 5 Circuit Description... 7 Alignment... 10 Contents Board Unit (Schematics, Layouts & Parts) MAIN Unit... 21 PLL Unit... 53 PA Unit... 59 PANEL Unit... 73 MIC Unit... 81 VR Unit... 82 BATT-CONN Unit... 83 REF Unit... 84

Specifications General Frequency Range: Emission Modes: Synthesizer Steps (Min.): Antenna Impedance: Operating Temp. Range: Frequency Stability: Supply Voltage: Current Consumption: Case Size (W x H x D): Weight (Approx.): Receive: 0.1-56 MHz, 76-108 MHz, 118-164 MHz, 420-470 MHz Transmit: 160-6 Meters, 2 Meters, 70 Centimeters (Amateur bands only) 5.1675 MHz (Alaska Emergency Frequency: USA only) A1 (CW), A3 (AM), A3J (LSB/USB), F3 (FM), F1 (9600 bps packet), F2 (1200 bps packet) 10 Hz (CW/SSB), 100 Hz (AM/FM/WFM) 50 Ohms, Unbalanced (M) +14 F to +140 F ( 10 C to +60 C) ±4 ppm from 1 min. to 60 min after power on. @25 C: 1 ppm/hour ±0.5 ppm/1 hour @25 C, after warmup (with optional TCXO-9) Normal: 13.8 VDC ±15 %, Negative Ground FNB-78 (Ni-MH Battery Pack): 13.2 V (Option) Squelched: 600 ma (Approx.) Receive: 1 A Transmit: 22 A 7.87 x 3.15 x 10.3 (200 x 80 x 262 mm) 8.6 lb (3.9 kg) (w/o Ni-MH battery, antenna, Microphone) Transmitter RF Power Output (@13.8 V DC): Modulation Types: FM Maximum Deviation: Spurious Radiation: Carrier Suppression: Opp. Sideband Suppression: SSB Frequency Response: Microphone Impedance: SSB/CW/FM AM Carrier 160-6 Meter: 100 W 25 W 2 Meter: 50 W 12.5 W 70 Centimeter: 20 W 5 W SSB: Balanced Modulator, AM: Early Stage (Low Level), FM: Variable Reactance ±5 khz (FM-N: ±2.5 khz) 50 db (1.8-29.7 MHz) 60 db (50/144/430 MHz) >40 db >50 db 400 Hz-2600 Hz ( 6 db) 200-10k Ohms (Nominal: 600 Ohms) 2

Specifications Receiver Circuit Type: Intermediate Frequencies: Sensitivity: Squelch Sensitivity: Image Rejection: IF Rejection: Selectivity ( 6/ 60 db): AF Output: AF Output Impedance: Double-Conversion Superheterodyne (SSB/CW/AM/FM) Superheterodyne (WFM) 1st: 68.33 MHz (SSB/CW/AM/FM); 10.7 MHz (WFM) 2nd: 455 khz SSB/CW AM FM 100 khz-1.8 MHz 32 µv 1.8 MHz-28 MHz 0.2 µv 2 µv 28 MHz-30 MHz 0.2 µv 2 µv 0.5 µv 50 MHz-54 MHz 0.125 µv 1 µv 0.2 µv 144/430 MHz 0.125 µv 0.2 µv (SSB/CW/AM = 10 db S/N, FM = 12 db SINAD) SSB/CW/AM FM 100 khz-1.8 MHz 1.8 MHz-28 MHz 2.5 µv 28 MHz-30 MHz 2.5 µv 0.32 µv 50 MHz-54 MHz 1 µv 0.16 µv 144/430 MHz 0.5 µv 0.16 µv HF/50 MHz: 70 db, 144/430 MHz: 60 db 60 db SSB/CW: 2.2 khz/4.5 khz AM: 6 khz/20 khz FM: 15 khz/30 khz FM-N: 9 khz/25 khz SSB (optional YF-122S installed): 2.3 khz/4.7 khz ( 66 db) CW (option YF-122C installed): 500 Hz/2.0 khz 2.5 W (@4 Ohms, 10% THD or less) 4-16 Ohms Specifications are subject to change without notice, and are guaranteed within the amateur bands 3

Exploded View & Miscellaneous Parts 4 5 4 5 4 RA0397700 TOP CASE RA0398000 SP NET (VND-100) 4 4 4 4 RA0398100 SPONGE RUBBER (SP) 4 RA0411700 HOLDER PLATE (MIC) RA0412300 PANEL ASSY R3135000A WASHER R0136380 COIL SPRING RA0415100 MAIN KNOB ASSY RA0411600 RUBBER RING 4 MIC Unit 17 17 RA0412200 SUPONGE RUBBER (MIC) 1 R6144801 NUT RA0412100 ROTARY KNOB (AF) M4090150 SPEAKER RA0413400 SP HOLDER RA0420000 SPONGE RUBBER S4000047 CASE LEG FF-003 (w/o RIVET) x 4 pcs S3000022 WIRE BIND PLT-1M BK-1 RA0411200 DOUBLE FACE (LCD) RA0423800 REFLECTOR SHEET RA0411400 LIGHT GUIDE (LCD) RA0423700 DIFFUSER SHEET 1 LCD RA0283900 SPONG RUBBER (SP-B) PANEL Unit RA0412000 R6054387B ROTARY KNOB (SQL) SPECIAL NUT RA0411800 ROTARY KNOB (VFO) RA0411900 ROTARY KNOB (CLAR) No. VXSTD P/N DISCRIPTION QTY. 1 U24306001 TAPTITE SCREW M3X6 4 2 U9900144 BINDING HEAD SCREW M3X7B 4 3 U24308002 TAPTITE SCREW M3X8NI 4 4 U31306007 OVAL HEAD SCREW M3X6B 8 5 U31205007 OVAL HEAD SCREW M2.6X5B 2 6 U20408007 BINDING HEAD SCREW M4X8B 2 7 U24206001 TAPTITE SCREW M2.6X6 10 8 U02208002 PAN HEAD SCREW SM2.6X8NI 2 9 U24208001 TAPTITE SCREW M2.6X8 2 10 U02308002 SEMS SCREW SM3X8NI 6 11 U20306002 BINDING HEAD SCREW M3X6NI 2 12 U00330007 PAN HEAD SCREW M3X30B 8 13 U9900076 HEX HEAD BOLT HSM4X16NI 1 14 U72004002 TOOTHED LOCK WASHER OW4NI 1 15 U20420007 BINDING HEAD SCREW M4X20B 2 16 U23206001 TAPTITE SCREW M2.6X6 5 17 U23105001 TAPTITE SCREW M2X5 2 18 U9900063 TAPTITE SCREW 2X3.3NI 1 1 1 17 16 18 RA0411300 LCD HOLDER 16 12 16 2 2 12 12 16 16 M2090029 FAN (x 2 pcs) RA0423600 SPONGE RUBBER (LED) VR Unit S5000057 LEAD CLAMPER (x 2 pcs) 7 9 7 8 7 2 RA0460300 SHIELD SHEET (DSP) RA0416500 HEATSINK PLATE 12 1 4 6 1 2 7 1 1 4 10 1 1 7 8 4 7 7 9 11 7 7 7 7 RA0398200 STAND 7 15 MAIN Unit RA041290A HOLDER (BATT SW) BATT-CONN Unit RA0412500 HANDLE RA0412600 HOLDER HANDLE (x 2 pcs) 9 7 7 9 RA0413100 SUPPORT (x 2 pcs) RA0452600 PACKING PAD (SHIELD) 1 6 4 7 14 1 4 13 3 3 3 RA0397900 SHIELD (CENTER) S4000043 CASE LEG FF-003 RA0397800 BOTTOM CASE (A) S4000043 CASE LEG FF-003 (x 2 pcs) RA3100700A FOOT (x 2 pcs) RA039760A CHASSIS (MAIN) 4 3 7 7 15

Block Diagram 5

Block Diagram Note: 6

Circuit Description The FT-897 internal assembly consists of the MAIN Unit, PLL Unit, PA Unit, Panel Unit, BATT-CONN Unit, REF Unit, MIC Unit, and the VR Unit. Receive Signal Circuitry RF Stages Signals between 0.1 and 56 MHz received at the antenna terminal pass through a low-pass filter, selected according to the receiving frequency, then pass to another low-pass filter, to remove unwanted out-of-band signals. The filtered receiving signal passes, through one of the following circuits, to the 1st Mixer Q1128 (SPM5001): (1) an attenuator network (-10dB) which consists of resistors R1101, R1108, R1109; (2) a through circuit enabled via diodes D1011 and D1012 (both DAP236U); or (3) RF amplifier Q1025 (2SC5374). Received 430 MHz signals, after passing through a high-pass filter composed of L3052, L3059, C3209, C3210, C3219, C3223, and C3319, are passed through low-pass filter composed of L3042, L3045, C3165, C3168, C3177, C3180, C3192, and C3196, and through a directional coupler, to the UHF T/R switch circuit composed of diode switch D3015/D3021 (both UM9957F), D3022, and D3066 (both HSU277). Then the signals are fed to the 1st Mixer Q1128 via the RF-AMP, Q1026 (2SK2685.) Received 145 MHz signals, after passing through a high-pass filter composed of L3060, L3050, L3047, C3200, C3203, C3220, and C3221, are passed through a low-pass filter composed of L3043, L3044, C3167, C3169, C3176, C3179, and C3191, and a directional coupler, to the VHF T/R switch circuit, composed of diode switch D3018/D3020 (both UM9957F). Then the signals are fed to 1st Mixer Q1128 via the RF-AMP, Q1024 (BB304CDW). Received 76-108 MHz signals, after passing through a high-pass filter composed of L3060, L3050, L3047, C3200, C3203, C3220, and C3221, are passed through low-pass filter composed of L3043, L3044, C3167, C3169, C3176, C3179, and C3191, and a directional coupler, to the T/R switch circuit, composed of diode switch D3018/ D3020 (both UM9957F). Then it is fed to the Wide-FM IF IC Q1058 (CXA1611N) on the MAIN Unit. 1st Mixer Circuit/1st IF Circuit The 1st mixer on the MAIN Unit consists of quad MOS FET Q1128 (SPN5001), where the receiving signal is mixed with the 1st local signal (68.430-538.330 MHz) from the PLL Unit. The resulting output signal (68.33 MHz) passes through monolithic crystal filter (MCF) XF1001 (MF68Q, BW: ±6.0 khz) to obtain the 1st IF signalwith a center frequency of 68.33 MHz. The IF signal passes through the 1st IF amplifier Q1073 (BB305CEW) to the 2nd Mixer, Q1083 and Q1084 (both 2SK302Y). 2nd Mixer Circuit/2nd IF Circuit The 2nd Mixer consists of FETs Q1083 and Q1084 (both 2SK302Y) on the MAIN Unit, where the 1st IF signal is mixed with the 2nd local signal (67.875 MHz). The resulting output signal (455 khz) is applied to the 2nd IF filter which is matched to the receiving mode: either CF1004, CF1005 or an optional mechanical filter. Noise Blanker Circuit A portion of the 2nd IF signal is amplified by Noise Blanker Amplifiers Q1075 and Q1079 (both BB305CEW) on the MAIN Unit, and then rectified by D1064 (1SS372). This output is applied to the Noise Blanker Controllers, Q1093 (2SC4154E) and Q1099 (2SA1602A), which a yield Blanking signal according to the timing of the incoming noise pulses. Then Blanking signal controls the Noise Blanker Gate D1066 (BAS316), to slice out the impulse noise from the signal. AGC Circuit The AGC circuit consists of D1061 (1SS372), transistor Q1090 (2SC4154E), and associated parts on the MAIN Unit. Output from the AGC circuit is fed back to the IF AGC circuit that controls the gain of the IF amplifier FETs. FM IF Circuit/FM Demodulator Circuit On FM, the 2nd IF signal passes through the buffer amplifier Q1094 (2SC4154E) and 2nd IF filters (CF1002 and CF1003) to the FM IF IC Q1080 (TA31135FN) which contains a mixer, limiter amplifier, filter amplifier, squelch trigger, and demodulator. The demodulated audio signal at Q1080 passes through a low-pass filter (R1339 and C1282) and a de-emphasis circuit (R1303 and C1345), then proceeds to the Audio Amplifier Circuit. The squelch circuit selectively amplifies the noise component of the demodulator output using the filter amplifier inside the FM IF IC and an active band-pass filter consisting of an externally attached resistor and capacitor. Signal detection is performed by D1057 (DA221). 7

Circuit Description SSB/CW Demodulator Circuit The 2nd IF SSB/CW signal passes through buffer amplifiers Q1088 and Q1081 (both BB305CEW) to the SSB balanced demodulator Q1071 (SA602AD) which produces audio by applying the carrier signal from the CAR- DDS IC Q1062 (AD9835BRU). The demodulated audio signal is stripped of high-frequency components by an active low-pass filter, op-amp IC Q1120 (NJM2902V), then is applied to the Audio Amplifier Circuit. AM Demodulator Circuit The 2nd IF AM signal passes through buffer amplifiers Q1088 and Q1081 (both BB305CEW) to the AM demodulator D1055 (BAS316), yielding demodulated audio signal which is applied to the Audio Amplifier Circuit. Audio Amplifier Circuit The demodulated audio signal is passed through AF pre-amplifier Q1119 (NJM2902V) and electronic volume control IC Q1087 (M62364EP) to the AF Amplifier IC Q1105 (TDA2003H) which drives the internal or external speaker to a maximum output of approximately 2.5 Watts. Transmit Signal Circuitry Microphone Amplifier Circuit The audio signal from microphone jack on the MIC Unit is amplified by audio amplifier Q1109 (2SC4154E) on the MAIN Unit, and then is applied to electronic volume control IC Q1087 (M62364EP), the level of which is set via the User Menu. SSB Modulator Circuit The output (audio signal) from the electronic volume control IC is passed through audio amplifier Q1118 (NJM2902V) to the balanced modulator IC Q1071 (SA602AD) which produces a Double Sideband (DSB) signal by applying the carrier signal from the CAR-DDS IC Q1062 (AD9835BRU). The DSB modulated signal (455 khz) is fed to ceramic filter CF1004 (or the optional mechanical filter) which strips residual carrier and the undesired sideband, resulting in a Single Sideband (SSB) signal. AM Modulator Circuit As in the SSB modulator circuit, a carrier signal appropriate to the transmitting mode (AM) from the CAR- DDS Unit and an audio signal from the microphone are applied to balanced modulator IC Q1071 (SA602AD). The control signal from Mode Switch IC Q1003 (BU4094BCFV) causes a voltage ( AM 5V ) to be sent from transistor Q1058 (2SC4154E). This voltage is applied to IC Q1071 via D1059 (BAS316), causing the balanced modulator to lose balance. The restored carrier signal and modulated signal are then fed to the TX mixer via ceramic filter CF1004. FM Modulator Circuit The output (audio signal) from the electronic volume control IC is passed through the pre-emphasis circuit which consists capacitor C1492 and resistors R1493 and R1477, and Instantaneous Deviation Control Q1119 (NJM2902V), to the splatter filter which consists Q1119, capacitor C1430, and resistors R1358 and R1384. The filtered audio signal is applied to the FM modulator circuit, which produces the FM signal. The FM modulator circuit uses a voltage controlled crystal oscillator (VCXO) which consists Q1055 (2SC4400), D1046 (1SV229), and X1002 (22.7767 MHz). 1st IF Circuit/1st Mixer Circuit The modulated SSB/AM signal is applied to the 2nd Mixer Q1082 (SA602AD), which produces the 68.33 MHz 2nd IF signal utilizing the 2nd local signal (68.875 MHz). The 2nd IF signal is fed through the 2nd IF filter XF1004 which strips away unwanted mixer products, then passes through the 2nd IF amplifier Q1061 (BB304CDW) to the double balanced mixer D1034 (HSB88WS) which produces the transmit frequency by applying the local signal (68.430-538.330 MHz) from the PLL Unit. The transmit signal is passed through a low-pass filter (1.8-29.7 MHz), a high-pass filter (50-54 MHz), a band-pass filter (144-146 MHz), or a band-pass filter (430-450 MHz) which consists of various inductors and capacitors. The filtered transmit signal is amplified by Q1017 (2SC3357), Q1011 (2SK2596), Q1006/Q1007 (2SK2973), and Q1001/1002 (2SK2975), and is applied to the Power Amplifier: Q3017/Q3018 (2SC5125: HF/50 MHz) or Q3016 (2SC3102: 144/430 MHz). 8

Circuit Description ALC Circuit The output from the directional coupler is routed from connector J3002 and applied to the ALC circuit via connector J1001 on the MAIN Unit. The ALC circuit consists of an op-amp circuit for amplifying the forward and reflected voltage, a time-constant ALC amplifier, and a transmit signal control circuit on the MAIN Unit. The forward voltage from connector J1001 on the MAIN Unit is added with a DC control voltage and is then applied to op-amp IC Q1111 (NJM2902V). The reflected voltage is added with a DC control voltage and is then applied to op-amp IC Q1112 (NJM2904V). In the event of high SWR conditions (SWR 3:1 or more), transmitter output is reduced, thus protecting the PA Unit from potential damage; a HI SWR indication also appears on the LCD, alerting the user to an antenna problem. The ALC amplifier magnifies the forward wave output via transistor Q1009 (2SC4154). This output then passes through a fast-attack, slow-delay RC time-constant circuit, which consists of R1051 and C1051, for input to the TX signal control circuit on the MAIN Unit. The TX control circuit adjusts the IF amplifier gain via gate 2 of FET Q1061 (BB304CDW) of the 2nd IF amplifier circuit, to prevent the TX output from exceeding the preset level. PLL Frequency Synthesizer The PLL Frequency Synthesizer consists mainly of the master reference oscillator circuit, 2nd local oscillator circuit, PLL IC, and CAR-DDS and REF-DDS units, which digitally synthesize carrier outputs, plus a PLL circuit which contains a voltage controlled oscillator (VCO). Master Reference Oscillator Circuit The master reference oscillator uses a Crystal Oscillator (oscillation frequency: 22.625 MHz) composed of Q5001 (2SC4400-4), X5001, TC5001, C5001, and R5005. The reference oscillator signal passes through a buffer amplifier Q5002 (2SC4400-4), and is then fed to the MAIN Unit via J5002. CAR-DDS Circuit REF-DDS Circuit DDS ICs Q1062 (AD9835BRU), and Q2016 (AD9850BAS) each contain a shift register, selector, phase accumulator, and ROM. The reference oscillation frequency (22.625 MHz) that is delivered to each of the DDS Units is applied to each DDS IC after amplification by transistors Q1043, Q1046, Q1048, and Q1059 (all 2SC4400-3). The DDS outputs contain digital amplitude data corresponding to serial frequency data from CPU IC Q1049. The DDS frequency range is 453.5 ~ 466.5 khz (center frequency = 455.0 khz) for the CAR-DDS, and 7.2-8.0 MHz for the REF DDS. 1st Local Oscillator Circuit VCO output is buffer-amplified by Q2011 (2SC5374) and Q2022 (UPC2713T), and passes through a low-pass filter. It is then fed to the TX/RX frequency mixer circuitry of the MAIN Unit. 2nd Local Oscillator Circuit The 2nd LO circuit is a Hartley-type overtone oscillator circuit (frequency: 67.875 MHz) composed of Q1052 (2SC4400-3) on the MAIN Unit. PLL Circuit The PLL circuit is a frequency mixing type composed of a VCO, mixer, PLL IC, and loop filter. The VCO consists of five circuits (VCO1, VCO2, VCO3, VCO4 and VCO5), with a frequency range of 68.430-538.330 MHz divided into five bands, allocated to the five VCO circuits. VCO1-VCO5 consist mainly of FETs Q2004, Q2005, and Q2006 (all 2SK210GR); transistors Q2009 and Q2010 (both 2SC5374); diodes D2001-D2006 (all HVC362), D2007 (1SV282), D2008 (1SV281), and D2009 (1SV286); and coils T2001-T2003, L2010, and L2011. The VCO switching signal from the connector J2002 is used to drive switching transistors Q2001, Q2002, Q2003, Q2012, and Q2013 (all DTC124EU) to switch the source terminal of the oscillator FET. The 68.430-538.330 MHz VCO signal is buffer-amplified by Q2023 (UPC1688G), and fed to PLL IC Q2021 (FQ7925.) The REF-DDS signal (7.2-8.0 MHz) is fed to PLL IC Q2021 after it passes through a low-pass filter composed of C2064, C2067, C2069, C2071, C2075, L2014, L2015, and L2016, and is fed to PLL IC Q2021 (FQ7925.) The phase of the reference frequency and that of the signal input to the PLL IC are compared, and a signal whose pulse corresponds to the phase difference is produced. 9

Alignment Introduction and Precautions The following procedures cover adjustments that are not normally required once the transceiver has left the factory. However, if damage occurs and some parts subsequently be replaced, realignment may be required. If a sudden problem occurs during normal operation, it is likely due to component failure; realignment should not be done until after the faulty component has been replaced. We recommend that servicing be performed by authorized Vertex Standard service technicians, experienced with the circuitry and fully equipped for repair and alignment. If a fault is suspected, contact the selling dealer for instructions regarding repair. Authorized Vertex Standard service technicians have the latest configuration information, and realign all circuits and make complete performance checks to ensure compliance with factory specifications after repairs. Those who do undertake any of the following alignments are cautioned to proceed at their own risk. Problems caused by unauthorized attempts at realignment are not covered by the warranty policy. Also, Vertex Standard must reserve the right to change circuits and alignment procedures in the interest of improved performance, without notifying owners. Under no circumstances should any alignment be attempted unless the normal function and operation of the transceiver are clearly understood, the cause of the malfunction has been clearly pinpointed and any faulty components replaced, and the need for realignment determined to be absolutely necessary. The following test equipment (and thorough familiarity with its correct use) is necessary for complete realignment. Most steps do not require all of the equipment listed, but the interactions of some adjustments may require that more complex adjustments be performed in a sequence. Do not attempt to perform only a single step unless it is clearly isolated electrically from all other steps. Rather, have all test equipment ready before beginning, and follow all of the steps in a section in the order they are presented. Required Test Equipment Digital DC Voltmeter (high-z, 1 M-Ohm/V) DC Ammeter RF Millivoltmeter AC Voltmeter RF Standard Signal Generator w/calibrated output and db scale, 0 dbµ = 0.5µV Signal Generator with calibrated output Spectrum Analyzer good to at least 1 GHz. Frequency Counter 50-Ohm Dummy Load (200 watts) 100-Ohm Dummy Load (200 watts) 150-Ohm Dummy Load (200 watts) In-Line Wattmeter (200 watts, 50-Ohm) Linear Detector RF Coupler Alignment Preparation & Precautions A 50-ohm RF Dummy load and in-line wattmeter must be connected to the main antenna jack in all procedures that call for transmission, except where specified otherwise. Correct alignment is not possible with an antenna. After completing one step, read the following step to determine whether the same test equipment will be required. If not, remove the test equipment (except dummy load and wattmeter, if connected) before proceeding. Correct alignment requires that the ambient temperature be the same as that of the transceiver and test equipment, and that this temperature be held constant between 68 ~ 86 F (20 ~ 30 C). When the transceiver is brought into the shop from hot or cold air, it should be allowed time to come to room temperature before alignment. Whenever possible, alignments should be made with oscillator shields and circuit boards firmly affixed in place. Also, the test equipment must be thoroughly warmed up before beginning. Note:Signal levels in db referred to in this procedure are based on 0 dbµ = 0.5 µv (closed circuit). 10

Alignment Local Oscillator Adjustment Reference Frequency Adjustment Connect the frequency counter to TP1032. Adjust the trimmer capacitor (TC5001) for 67.875000 MHz (± 10 Hz) on the frequency counter. Connect an RF millivoltmeter or an oscilloscope to pin 2 of J5002 (TP1032) and confirm that the output level is 115 mv (± 30 mv) rms or 315 mv (± 80mV) p-p. 3ad Local Adjustment Connect an RF millivoltmeter or an oscilloscope to TP1037. Key the transceiver on CW, and adjust T1025 for maximum indication on the RF millivolt-meter. Confirm that the indicated voltage is 100 mv (± 30 mv) rms or 300 mv (± 100mV) p-p. PLL Adjustment VCO VCV Adjustment Connect the DC voltmeter to pin 6 of J2002 (TP1028) and, referring to the table below, tune the transformer/ inductor on each frequency listed. Then confirm that the correct voltage is present, or adjust the listed component for the required voltage. Tune to : Adjust / Confirm For 13.895 MHz Adjust T2001 5.5V ±0.5V 76.000 MHz Confirm At least 0.8V 32.995 MHz Adjust T2002 5.5V ±0.5V 13.900 MHz Confirm At least 0.8V 55.995 MHz Adjust T2003 5.5V ±0.5V 88.000 MHz Confirm At least 0.8V 163.995 MHz Adjust L2010 5.5V ±0.5V 118.000 MHz Confirm At least 0.8V 469.995 MHz Adjust L2011 5.5V ±0.5V 420.000 MHz Confirm At least 0.8V TP1028 TP1029 TC5001 1st Local Output Level Connect the RF millivoltmeter to pin 11 of J2002 (TP1029), and set the transceiver to 28.000 MHz. Confirm that the RF level is at least +3 dbm or 300 mv rms. TP1032 T1025 TP1037 11

Alignment PLL Unlock Connect the DC voltmeter to pin 1 of J2002 (TP1027). Disconnect the reference oscillator input by unplugging the cable; confirm that the voltmeter shows less than 0.5 V and that UNLOCK is displayed on the LCD. Re-connect the reference input, and confirm that the voltmeter shows at least 3.5 V and tat the LCD returns to its normal display. Idling Current Adjustment Before alignment, set the mode to CW and tune the transceiver to 1.800 MHz. Nothing should be connected to the CW Key Jack. Switch off S1001. Pre-Driver Stage Idling Current Connect the ammeter between TP1019 and TP1020. Press the PTT, and adjust VR1004 for an indication of 35 ma (±2 ma) on the ammeter. Driver Stage Idling Current Connect the ammeter between TP1017 and TP1018. Press the PTT and adjust VR1003 for an indication of 30 ma (±2mA) on the ammeter. Exciter Stage Idling Current Terminate J1004 into a ammeter. Turn both VR1001 and VR1002 fully counterclockwise. Press the PTT and adjust VR1002 for an indication of 100mA (±10 ma) on the ammeter. Press the PTT and adjust VR1001 for an indication of 200mA (±10 ma) on the ammeter. Re-connect J1004 and switch on S1001. TX IF Adjustment SSB/CW TX IF Adjustment Tune the frequency to the 14 MHz band. Connect the RF millivoltmeter to TP1033, and terminate J1002 into a 50-Ohm dummy load. Inject a 1 khz tone at 1 mv level to the MIC jack. MIC GND MIC PTT GND Key the transmitter, and adjust T1033 for maximum indication on the RF millivoltmeter. TP1033 T1021 T1013 T1012 T1011 S1001 TP1017 VR1004 VR1003 TP1027 T1014 L1049 T1023 VR1005 T1033 TP1018 TP1019 TP1020 VR1002 VR1001 J1004 J1002 J1003 12

Alignment FM TX IF Adjustment Tune the frequency to the 28 MHz band. Connect the RF millivoltmeter to TP1033 and leave J1002 terminated into a 50-Ohm dummy load. Key the transmitter in the FM mode, and adjust T1014, T1023, and T1021 alternately for maximum indication on the RF millivoltmeter. Connect the frequency counter to TP1033. Key the transmitter in the FM mode without microphone input. Adjust L1049 for a reading of 68.3300 MHz (±100 Hz). Carrier Balance Adjustment Tune the frequency to the 14 MHz band. Terminate J1002 into a 50-Ohm dummy load and connect a spectrum analyzer or a RF millivoltmeter at this point. Key the transmitter in the USB mode without microphone input. Adjust VR1005 for maxi-mum carrier suppression on the spectrum analyzer or for minimum indication on the RF millivoltmeter. VHF TX BPF Adjustment Set the frequency to 145.995 MHz. Connect the spectrum analyzer to J1002, which should be terminated into a 50-Ohm dummy load. Inject a 1 khz tone at 1 mv level to the MIC jack. Key the transceiver in the USB mode, and adjust T1013, T1012, and T1011 alternately for maximum indication on spectrum analyzer. UHF TX BPF Adjustment Set the frequency to 430.000 MHz. Connect the spectrum analyzer to J1002, which should be terminated into a 50-Ohm dummy load. Inject a 1 khz tone at 1 mv level to the MIC jack. Key the transceiver in the USB mode, and adjust TC1004, TC1003 and TC1002 alternately for maximum indication on the spectrum analyzer. T1018 T1019 T1024 TC1003 TC1002 TC1005 T1008 T1010 T1026 T1028 TP1044 T1029 T1030 T1034 T1035 T1027 T1005 T1009 T1006 T1004 TC1001 T1031 TP1043 T1036 T1037 13

Alignment RX Adjustment The PA Unit must be connected during RX adjustments. The signal generator should not be connected to J1003 directly because DC voltage is present there. RX IF Adjustment Connect the signal generator to the antenna connector, and the SINAD meter to the speaker jack. SSB IF Adjustment Tune the transceiver to 51.995 MHz. Inject an RF signal from a signal generator at 0 dbµ output. Adjust T1018, T1019, T1024, T1026, T1028, T1030, T1035, T1036, T1037, T1034 and T1029 alternately for maximum indication on the DC voltmeter. Several passes may be necessary, as the adjustments inter-react to some degree. FM IF Adjustment Tune the transceiver to 51.995 MHz. Inject an RF signal from a signal generator at 5 dbµ output, with 1 khz AF FM modulation at ±3.5 khz deviation. Adjust T1024, T1026, and T1028 alternately for maximum level on the S-meter. Air-Band Reception Adjustment Connect the DC voltmeter to TP1044. Tune the transceiver to 128.00 MHz in the AM mode. Inject an RF signal from the signal generator at 20 dbµ output, with 30% AM modulation at 400 Hz audio frequency. Adjust T1005 and T1008 for minimum indication on the DC voltmeter. VHF Band Alignment Connect the DC voltmeter to TP1044. Tune the transceiver to 145.995 MHz in the CW mode. Inject an RF signal from a signal generator at 20 dbµ output. Adjust T1006, T1009 and T1010 alternately for minimum indication on the DC voltmeter. UHF Band Alignment Connect the DC voltmeter to TP1044. Tune the transceiver to 439.995 MHz in the CW mode. Inject a RF signal from the signal generator at 20 dbµ output. Adjust TC1001 for minimum indication on the DC voltmeter. W-FM Reception Adjustment Connect the SINAD meter to the speaker jack. Tune the transceiver to 88.00 MHz. Inject a RF signal from the signal generator at 30dBu output, with ±22.5 khz deviation FM modulation of a 1 khz audio signal. Adjust TC1005 for the best SINAD sensitivity. Then reduce the output level of the signal generator to where the signal just begins to sound slightly noisy, and adjust TC1005 again for best SINAD. Image Rejection Trap Adjustment Connect the AF millivoltmeter to the speaker jack. Tune the transceiver to 51.995 MHz in the FM mode. Inject an RF signal from the signal generator at 68.330 MHz, with 70 dbµ output. Adjust T1004 for minimum indication on the AF millivoltmeter. Then increase the output level of the signal generator slightly and adjust T1004 again, so as to ensure maximum notching of the image. Noise Blanker Adjustment Connect the DC voltmeter to TP1043. Tune the transceiver to 51.995 MHz and inject an RF signal from the signal generator at 20 dbµ output. Activate the noise blanker, and adjust T1027 and T1031 for minimum indication on the DC voltmeter connected to TP1043. 14

Alignment Power Amplifier Adjustment HF/50 MHz Idling Current Adjustment Tune the transceiver to any HF band, or to the 50 MHz band. Disconnect the jumper between TP3021 and TP3022. Connect the ammeter between TP3021 and TP3022. Turn VR3002 fully counterclockwise. Press the PTT, and adjust VR3002 for an indication of 300 ma (±10 ma) on the ammeter. Re-connect TP3021 and TP3022. V/UHF Idling Current Adjustment Tune the transceiver to the 430 MHz band. Connect the ammeter between TP3021 and TP3022. Connect the ammeter between TP3021 and TP3022. Turn VR3001 fully counterclockwise. Press the PTT, and adjust VR3001 for an indication of 300 ma (±10 ma) on the ammeter. Re-connect TP3021 and TP3022. Directional Coupler Balance Adjustment Terminate the antenna jack into a 50-Ohm dummy load. Set the mode to CW, and connect the DC voltmeter to TP3001. Tune the transceiver to the 28 MHz band, and key the transceiver. Adjust TC3002 for minimum indication on the DC voltmeter. Tune the transceiver to 439.995 MHz, and key the transceiver. Adjust VR3003 for minimum indication on the DC voltmeter. Leave the transceiver on 439.995 MHz band and key the transceiver. Adjust TC3001 for maximum indication on the RF Power meter. TC3002 VR3003 TP3021 TP3022 TP3001 TC3001 VR3002 VR3001 15

Alignment Battery Indicator Alignment Connect a DC power supply to pin 4 of JP4007, and connect pin 6 to the ground lead from the power supply. Adjust the power supply voltage exactly to 11.0 V. Adjust VR4001 until you see an orange blink on the BATT-A indicator. Software Menu Alignment The antenna connector should be connected to a dummy load (in cases where transmission is involved) or the signal generator (in the case of reception). General alignment conditions are as follows unless otherwise noted. AF-gain knob: RF-gain knob: SQL: ATT/IPO/CTCSS/DCS: Output power: AGC: Break-in: CW Keyer: VOX: Center Fully clockwise Fully counterclockwise Off High Auto On Off Off Press and hold in the Multi Function Keys [A], [B], [C] simultaneously and turn on the transceiver while holding them in; the alignment menu will then be activated (you will hear a diddle-diddle-diddle opening tone sequence to confirm that the alignment menu has been activated). In the alignment procedures, each alignment parameter is selected by rotating the MAIN dial. Each Alignment item is selected by rotating the MEM/VFO CH knob. To store the alignment parameters when you are satisfied with the adjustment, press the [MENU] key for longer than a half second. VR4001 JP4007 16

Alignment RX Gain Adjustment Select the CW mode. Tune the transceiver to the 1.8 MHz band. Select HF1RXG in the menu by rotating the MEM/VFO CH knob, if necessary. Inject an RF signal from the signal generator at 9 dbµ output. Adjust the HF1RXG parameter by rotating the main dial to the point where the first dot of the S-meter (S1) appears. The other RX gain adjustments (see the chart below) should be performed in the same way. The output levels of the signal generator at each frequency are shown below. Menu Frequency Output Level of SG 01: HF1RXG 1.8 MHz Band 9 dbu 02: HF2RXG 7 MHz Band 9 dbu 03: HF#RXG 21 MHz Band 6 dbu 04: 50MRXG 50 MHz Band 0 dbu 05: VHFRXG 144 MHz Band 0 dbu 06: UFFRXG 430 MHz Band 0 dbu SSB S-Meter Adjustment Tune the transceiver to the 21 MHz band in the CW mode. Inject an RF signal from the signal generator at 36 dbµ output. Select menu item 07: SSB-S9 and press the [A] key to set this parameter. Tune the transceiver to the 21 MHz band in the CW mode. Inject an RF signal from the signal generator at 86 dbµ output. Select menu item 08: SSB-FS and press the [A] key to set this parameter. FM S-Meter Adjustment Tune the transceiver to the 144 MHz band in the FM mode. Inject an RF signal from the signal generator at 0 dbµ output, with ±3.5 khz deviation FM Modulation of a 1 khz tone. Select menu item 09: FM-S1 and press the [A] key to set this parameter. Increase the output level of the signal generator up to 25 dbµ. Select menu item 10: FM-FS and press [A] key to set this parameter. FM Center Meter Adjustment Tune the transceiver to the 144 MHz band in the FM mode. Inject an RF signal from the signal generator at 10 dbµ output, with ±3.5 khz deviation FM Modulation of a 1 khz tone. Set the frequency of the signal generator 3 khz below the receiving frequency of the transceiver. Select menu item 11: DISC-L and press the [A] key to set this parameter. Set the frequency of the signal generator 3 khz above the receiving frequency of the trans-ceiver. Select menu item 12: DISC-H and press the [A] key to set this parameter. FM Squelch Adjustment Tune the transceiver to the 144 MHz band in the FM mode. Confirm that the squelch knob is turned fully counterclockwise. Inject an RF signal from the signal generator at -15 dbµ output, with ±3.5 khz deviation FM Modulation of a 1 khz tone. Select menu item 13: FM-TH1 and press the [A] key to set this parameter. Select menu item 14: FM-TH2 and press the [A] key again. Inject an RF signal from the signal generator at 0 dbµ output, with ±3.5 khz deviation FM Modulation of a 1 khz tone. Select menu item 15: FM-TI1 and press the [A] key to set this parameter. Select menu item 16: FM-TI2 and press the [A] key again. Power Supply Voltage Display Adjustment Tune the transceiver to the 144 MHz band in the FM mode. Confirm that the power supply voltage is 13.8 V (±0.1 V). Select menu item 17: VCC and adjust this parameter such that 138 is displayed on the LCD. 17

Alignment Over-current Protection Adjustment Set the mode to CW. Select menu item 18: HF1-IC. Tune the transceiver to the 1.8 MHz band and key the transceiver. Adjust this parameter for 140 Watts of transmission power. Select menu item 19: HF2-IC. Tune the transceiver to the 7 MHz band and key the trans-ceiver. Adjust this parameter for 130 Watts of transmission power. Select menu item 20: HF3-IC. Tune the transceiver to the 21 MHz band and key the transceiver. Adjust this parameter for 130 Watts of transmission power. Select menu item 21: 50M-IC. Tune the transceiver to the 50 MHz band and key the transceiver. Adjust this parameter for 120 Watts of transmission power. Select menu item 22: VHF-IC. Tune the transceiver to the 144 MHz band and key the transceiver. Adjust this parameter for 60 Watts of transmission power. Select menu item 23: UHF-IC. Tune the transceiver to 430.000 MHz and key the trans-ceiver. Adjust this parameter for 25 Watts of transmission power. RF Power Adjustment Tune the transceiver to the 1.8 MHz band in the CW mode. Select menu item 24: HF1-MAX. Key the transmitter, and adjust this parameter for 100 Watts (±5 W) of transmission power. Select menu item 25: HF1-MID2. Key the transmitter, and confirm that the output power is 50 W (±5W). In case the transmission power is not within the specified tolerance, adjust this parameter for 50 W (±5 W) of transmission power. Select menu item 26: HF1-MID1. Key the transmitter, and confirm that the output power is 10 W (±1 W). In case the power is not within the specified tolerance, adjust this parameter for 10 W (±1 W) of transmission power. Select menu item 27: HF1-MIN. Key the transmitter, and confirm that the output power is 5 W (±1 W). In case the power is not within the specified tolerance, adjust this parameter for 5 W (±1 W) of transmission power. The other RF power adjustment menus, [HF2-**] and [HF3-**], should be adjusted in the same manner as shown above for the 7 MHz and 21 MHz bands respectively. Tune the transceiver to the 50 MHz band in the CW mode. Select menu item 36: 50M-MAX. Key the transmitter, and adjust this parameter for 100 W (±5 W) of transmission power. Select menu item 37: 50M-MID2. Key the transmitter, and confirm that the output power is 50 W (±5 W). In case the transmission power is not within the specified tolerance, adjust this parameter for 50 W (±5 W) of transmission power. Select menu item 38: 50M-MID1. Key the transmitter, and confirm that the output power is 20 W (± 2W). In case the power is not within the specified tolerance, adjust this parameter for 20 W (±2 W) of transmission power. Select menu item 39: 50M-MIN. Key the transmitter, and confirm that the output power is 5 W (±1 W). In case the power is not within the specified tolerance, adjust this parameter for 5 W (±1 W) of transmission power. Tune the transceiver to the 144 MHz band in the CW mode. Select menu item 40: VHF-MAX. Key the transmitter, and adjust this parameter for 50 W (±2.5 W) of transmission power. Select menu item 41: VHF-MID. Key the transmitter, and confirm that the output power is 20 W (±2 W). In case the transmission power is not within the specified tolerance, adjust this parameter for 20 W (±2 W) of transmission power. 18

Alignment Select menu item 42: VHF-MIN. Key the transmitter, and confirm that the output power is 5 W (±1 W). In case the power is not within the specified tolerance, adjust this parameter for 5 W (±1 W) of transmission power. Tune the transceiver to the 430 MHz band in the CW mode. Select the menu item 43: UHF-MAX. Key the transmitter, and adjust this parameter for 20 W (±1 W) of transmission power. Select menu item 44: UHF-MID. Key the transmitter, and confirm that the output power is 20 W (±0.3 W). In case the transmission power is not within the specified tolerance, adjust this parameter for 20 W (±0.3 W) of transmission power. TX Gain Adjustment Select the USB mode. Inject a 1 mv audio signal at a frequency of 1 khz from the AF generator into the MIC jack. Tune the transceiver to the 1.8 MHz band and key the transmitter. Select menu item 45: HF1TXG and adjust this parameter for 70 W (±10 W) of transmission power. The other TX gain adjustment menus, 46: HF2TXG, 47: HF3TXG, and 48: 50MTXG, should be adjusted in the same manner as detailed above on the 7 MHz, 21 MHz, and 50 MHz bands, respectively. Tune the transceiver to the 144 MHz band and key the transmitter. Select menu item 49: VHFTXG and adjust this parameter for 35 W (±5 W) of transmission power. Tune the transceiver to the 430 MHz band and key the transmitter. Select menu item 50: UHFTXG and adjust this parameter for 10 W (±2 W) of transmission power. Reverse ALC Adjustment Set the mode on CW, and connect a 150-Ohm dummy load to the antenna connector. Key the transceiver on the 1.8 MHz band, and select menu item 53: HF1-RV; adjust this parameter for an S-8 S-meter reading on the LCD. The other reverse ALC adjustment menus, 54: HF2- RV, 55: HF3-RV, and 56: 50M-RV, should be adjusted in the same manner as shown above on the 7 MHz, 21 MHz, and 50 MHz bands, respectively. Key the transceiver on the 144 MHz band and select menu item 57: VHF-RV; adjust this parameter for an S-6 S-meter reading on the LCD. Key the transceiver on the 430 MHz band and select menu item 58: UHF-RV; adjust this parameter for an S-3 S-meter reading on the LCD. Carrier Level Adjustment Tune the transceiver to the 21 MHz band in the CW mode. Connect a 50-Ohm dummy load to the antenna connector. Select menu item 59: CW-CAR and key the transceiver. Set this parameter such that the center of the meter on the LCD lights up. Connect the oscilloscope to the antenna connector via an appropriate attenuator. Set the mode to AM. Select menu item 60: AM-CAR. Inject a 1.5 mv audio signal at a frequency of 1 khz from the audio generator into the microphone jack. Key the transceiver and adjust this parameter for 33% AM modulation on the oscilloscope. ALC Meter Adjustment Tune the transceiver to the 21 MHz band in the USB mode. Select menu item 51: ALC-1. Key the transceiver without microphone input and press the [A] key. Now, a value which the microprocessor computes will be displayed on the LCD. Rotate the main dial to adjust this parameter to a reading four digits lower than the parame-ter value displayed in the previous step. After setting the parameter, confirm that all the dots of the ALC meter have gone out. Select menu item 52: ALC-M. Inject a 4.0mV AF signal at 1 khz audio frequency from an audio generator and key the transceiver. Press the [A] key and confirm that 9 dots of the ALC meter light up on the LCD. 19

Alignment FM Modulation Adjustment Tune the transceiver to the 144 MHz band in the FM mode. Connect the FM linear detector to the antenna connector via an appropriate attenuator. Select menu item 61: DEV-W. Inject a 15 mv audio signal at 1 khz from the audio generator. Key the transceiver and adjust this parameter for a maximum deviation of ±4.5 khz (±0.2 khz) on the FM linear detector. Change the menu item to 62: DEV-N. Key the transceiver and adjust this parameter for maximum deviation of ±2.25 khz (±0.1 khz) on the FM linear detector. Change the menu item to 63: M-MTR. Key the transceiver and set this parameter for an S-9 indication on the S-meter on the LCD. Change the menu item to 64: DTMF. Key the transceiver with DTMF signal input (press any DTMF key on the MH-36E8J microphone) and adjust this parameter for a maximum deviation of ±3.5 khz (±0.3 khz) on the FM linear detector. Change the menu item to 65: CTCSS. Key the transceiver without microphone input and adjust this parameter for a maximum deviation of ±0.7 khz (±0.1 khz) on the FM linear detector. Change the menu item to 66: DCS. Key the transceiver without microphone input and adjust this parameter for a maximum deviation of ±0.7 khz (±0.2 khz) on the FM linear detector. VSWR Adjustment Connect a 100-Ohm dummy load to the antenna connector. Tune the transceiver to the 14 MHz band in the CW mode. Select menu item 69: SWR2. Key the transceiver and press the [A] key to set this parameter. Connect a 150-Ohm dummy load to the antenna connector. Select menu item 70: SWR3. Key the transceiver and press the [A] key to set this parameter. ATAS control voltage confirmation Connect the DC voltmeter to the ANT (HF/50 MHz) jack. Select menu item 71: ATAS. Press the [A] key, and confirm that the voltage is 9.0 to 10.0 Volts. Press the [B] key, and confirm that the voltage is 7.5 to 8.5 Volts. Press the [C] key, and confirm that the voltage is more than 10.5 Volts. This completes the internal alignment routine for all bands. To save all settings and exit, press and hold in the [F] key for at least 0.5 second. SSB Carrier Point Adjustment Tune the transceiver to the 21 MHz band. Select menu item 67: LSB-CP. Set the mode to LSB, and inject a 1.0 mv audio signal from the audio generator into the MIC jack. Lower the audio frequency down to 400 Hz and adjust this parameter for 20 W output power from the transceiver. Change the audio frequency to 2600 Hz, and confirm that the output power is at least 20 W (± 2 W). The adjustment for the USB carrier point is performed in the same manner as done for LSB by changing the transmission mode to USB and the menu item to 68: USB-CP. 20

Circuit Diagram MAIN Unit 21

MAIN Unit Note: 22

MAIN Unit Parts Layout A BU4094BCFV-E2 (Q1003, 1004, 1010) BU4066BCFV-E2 (Q1121, 1122) M62352GP (Q1016) BU4011BF (Q1113) B C D E F NJM2902V (Q1114, 1120) 1 HD64F2134FA20 (Q1049) TC4W53FU (Q1038) 2SK2975 (Q1001, 1002) 24LC128T (Q1065) RT1N241M (N2) (Q1047, 1086) SA602AD (Q1071, 1082) UMH6N (H6) (Q1124) 2SB624 (BV3) (Q1013, 1020) 2SA1602A (MF) (Q1036) KIA7808API (Q1014) 2SK2973 (K1) (Q1006, 1007) TDA2003H (Q1105) 2 3 2SC4154E (LE) (Q1037, 1057, 1064, 1069, 1077, 1085, 1090, 1093) 4 UMC5N (C5) (Q1018, 1060) FMG5 (G5) (Q1015) 2SD2211 (DQR) (Q1108) TC4S66F (C9) (Q1100) DTC114EU (24) (Q1053) TC4S81F (C2) (Q1129) 5 SPM5001 (Q1128) TA75S01F (SA) (Q1095) 6 DAP236U (X) (D1019, 1031) DAP222 (P) (D1079) MC2850 (A7) (D1032) DAN222 (N) (D1083) DA221 (K) (D1043) 1SS372 (N9) (D1061, 1064) IMN10 (N10) (D1044, 1047, 1048) HSB88WSTR (D1034) 7 Side A 23

MAIN Unit Parts Layout a b c d e f BU4053BCFV-E2 (Q1066) TA31136FN (Q1080) AD9835BRU (Q1062) CXA1611N (Q1058) 1 AK7712VT (Q1092) NJM2904V (Q1112, 1117, 1123) TC4W53FU (Q1067, 1098) 2 3 4 5 M51132FP (Q1103) M62364FP (Q1087) UPC2710T (C1F) (Q1022) NJM2902V (Q1111, 1115, 1116, 1118, 1119) UMD2N (D2) (Q1029) 2SC4154E (LE) (Q1005, 1008, 1009, 1012, 1039, 1042, 1044, 1045, 1054, 1055, 1068, 1070, 1074, 1076, 1078, 1094, 1096, 1097, 1109) 2SC5374 (NA) (Q1025) 2SC4400 (RT) (Q1041, 1043, 1046, 1048, 1051, 1051, 1052, 1056, 1059) 2SJ355 (PQ) (Q1031) M5278L05M (Q1028) 2SC3357 (RK) (Q1017) 2SA1602A (MF) (Q1040, 1050, 1099) 2SK2685 (WV-) (Q1026) UMH6N (H6) (Q1027, 1125, 1126) PST3445UR (DF) (Q1030) BA05FP (Q) (Q1019) BB305CEW-TL (EW) (Q1073, 1075, 1079, 1081, 1088) DTC114EU (24) (Q1102, 1110) 2SK302Y (TY) (Q1083, 1084) FMG5 (G5) (Q1104, 1106) 2SK2596 (BX) (Q1011) UMC5N (C5) (Q1033, 1034, 1063) RT1N241M (N2) (Q1021, 1032, 1035, 1091, 1107) 6 7 Side B 24 BB304CDW (DW) (Q1023, 1024, 1061, 1089) DAP236U (X) (D1001, 1002, 1011, 1012, 1018, 1025, 1030, 1035) DAP222 (P) (D1063, 1065, 1072, 1076, 1078) HZM27WA (27A) (D1077, 1080) 1SS302 (C3) (D1010) DA221 (K) (D1037, 1057) 1SS372 (N9) (D1058) DAN222 (N) (D1033, 1069, 1070) DAN235U (M) (D1039, 1049, 1050, 1054) MA132WK (MU) (D1029)

MAIN Unit Parts List *** MAIN UNIT *** PCB with Components CP7373005 USA TYP A2 PCB with Components CP7373006 EXP TYP A1 PCB with Components CP7373007 EXP TYP A2 PCB with Components CP7373008 EXP TYP A3 PCB with Components CP7373011 EXP TYP B3 PCB with Components CP7373014 EXP TYP C3 PCB with Components CP7373015 EXP TYP D1 PCB with Components CP7373016 EXP TYP D2 PCB with Components CP7373017 AUS TYP H1 PCB with Components CP7373018 AUS TYP H2 PCB with Components CP7373021 FRA TYP E3 Printed Circuit Board FR007880C 1- C 1001 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B c4 C 1002 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B c4 C 1003 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B d6 C 1004 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B d6 C 1005 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- B d6 C 1007 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A E7 C 1008 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A E7 C 1009 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A E7 C 1010 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A E6 C 1011 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A E7 C 1012 CHIP CAP. 100pF 50V CH UMK105CH101JW-F K22178282 1- B a6 C 1013 CHIP CAP. 220pF 25V CH TMK105CH221JW-F K22148246 1- B a6 C 1014 CHIP CAP. 100pF 50V CH UMK105CH101JW-F K22178282 1- B a6 C 1015 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- B a6 C 1016 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- B a6 C 1017 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- B a6 C 1018 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A F6 C 1019 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A F6 C 1020 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- A F6 C 1021 AL.ELECTRO.CAP. 47uF 16V ECEV1CA470SP K48120005 1- A D5 C 1023 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B c5 C 1024 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B c7 C 1025 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D6 C 1026 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D6 C 1029 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D6 C 1030 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B c5 C 1031 CHIP CAP. 0.01uF 16V B GRM36B103K16PT K22128804 1- A C4 C 1032 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- B a6 C 1033 CHIP CAP. 0.001uF 50V B UMK105B102KW-F K22178829 1- B a6 C 1034 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A D6 C 1035 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A D6 C 1037 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D6 C 1038 CHIP CAP. 12pF 50V CH GRM39CH120J50PT K22174213 1- A D6 C 1039 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1- A D6 C 1040 CHIP TA.CAP. 1uF 16V TESVA1C105M1-8R K78120009 1- B a6 C 1042 CHIP CAP. 0.01uF 16V B GRM36B103K16PT K22128804 1- A C4 C 1043 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 1- B b6 C 1044 CHIP CAP. 0.01uF 50V B GRM39B103M50PT K22174823 1- B b6 C 1045 AL.ELECTRO.CAP. 10uF 16V RV2-16V100MB55-R K48120014 1- A D5 C 1046 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D5 C 1047 CHIP TA.CAP. 4.7uF 10V TEMSVA1A475M-8R K78100022 1- B a6 C 1049 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A E6 C 1050 CHIP CAP. 8pF 50V CH GRM39CH080D50PT K22174209 1- B b6 C 1051 CHIP TA.CAP. 2.2uF 10V TESVA1A225M1-8R K78100021 1 B a6 C 1052 CHIP CAP. 0.01uF 16V B GRM36B103K16PT K22128804 1- A C3 C 1053 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A D5 C 1054 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B b6 25