CE-9 xx その他 その他 -//etl_ce_9xx
CE-9xx Specifications Nominal Voltage V DC./. DC. DC DC./. DC. DC./. Input Voltage Range V DC.-. DC.-. DC4.-. DC.-. DC.-. DC.-. Efficiency (typ) (*) 8 88 7 8 7 9 Nominal Voltage VDC... -... -. 7. Maximum Current (*) ma /ch /ch Maximum Power (*) W..98......9. Output Max Power Total Regulation (max) (*4) 4 4 Maximum Ripple & Noise (typ) (*) mvp-p Maximum Ripple & Noise (max)(*) mvp-p Voltage Adjustable Range VDC Fixed.-..-. -.8--. 4.--.8 Fixed -4.--. -.-. -8 Over Current Protection Available Function Over Voltage Protection Remote ON/OFF Control Operating Temperature - to +8 Storage Temperature - to +8 Operating Humidity RH -9 (the conditions of maximum 8C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Humidity RH -9 (the conditions of maximum 8C in wet bulb temperature and non-condensation should be ensured.) Vibration -Hz, 4 minutes sweep and 98m/s² (G) acceleration, directions,.h for each, in non-operation Shock 98m/s² (G), ms, directions, times for each, in non-operation Weight g. Mechanical Size (W x H x D) mm 8 x 4 x.8 8-ø.8 Outline Drawing..4. 4 CE-9xx TDK-Lambda MADE IN JAPAN Lot No. 8 7.8±. P P P.4.±. 8±. 9.4 4max. P=±..4 (9.4) Derating Curve 8 8
CE-9xx Specifications Input Voltage Range Nominal:VDC V DC4.-. Efficiency (typ) (*) 8 8 7 7 Nominal Voltage (*) V. - - - -4 Maximum Current ma 8 Maximum Power (*) W..8 Maximum Line Regulation Within input voltage range (typ).%.%.%.% Output Maximum Load Regulation (-%)(typ).% %.% Temperature Coefficient (- to C)(typ) (*4).. Max Power Total Regulation (max) Maximum Ripple & Noise (typ) (*) mvp-p 7 Maximum Ripple & Noise (max) (*) mvp-p Acceptable Output Capacitorco (*) F 8.8 Over Current Protection Available Function Over Voltage Protection Remote ON/OFF Control Operating Temperature - to +7 Storage Temperature - to +8 Operating Humidity RH -9 (the conditions of maximum 8C in wet bulb temperature and non-condensation should be ensured.) Environment Storage Humidity RH -9 (the conditions of maximum 8C in wet bulb temperature and non-condensation should be ensured.) Vibration -Hz, minutes sweep and 98m/s² (G) acceleration, directions, h for each, in non-operation Shock 98m/s² (G), ms, directions, times for each, in non-operation Weight g. Mechanical Size (W x H x D) mm 7. x 4. x.8 (*) In nominal input voltage, maximum output current, and Ta=C. (*) V in CE 994 is the value when and + are short-circuited. -V in CE 99 is the value when and + are short-circuited. (*) The maximum output power value is between -C and +C. For use outside this temperature rage, derating is needed. (*4) Temperature coefficient in -C - +C. (*) Frequency range in measurement (MHz). Ripple & noise value is that in the condition where a specified external output capacitor Co is attached to the output terminal. (*) Use an external output capacitor with max. impedance and. max. loss angle. Recommended capacitor: TE series (MATSUSHITA) With nominal input/output voltage, maximum output current, and Ta=C, if not specified separately. 8-ø.8 Outline Drawing.. 4 CE-9xx TDK-Lambda MADE IN JAPAN Lot No. 8 7.8 P P P.4... (Board thickness) (.7) 7. 4.max. P=. if not specified separately. Unit: mm 4.9 (8.9) Derating Curve 8 7 8
4 CE-9xx Instruction Manual. CE-9,-97,-98,-99,-9,-9,-9,-9A,-98LC,-9 -. Connection diagram -. Output voltage setting CE-9,-9 CE-97,-98,-98LC Terminal assignments No. No. No. No.4 No. No. No.7 No.8 CE-9 CE-9 Vo CE-97 CE-98 CE-98LC CE-99 CE-9 Vo CE-9 CE-9A CE-9 CE-99,-9 -. Output voltage setting To change the output voltage, calculate Rex by assigning the absolute value of the output voltage to in the expression below, and attach it between the terminals to be connected. CE-97 7.9-.9 - CE-9 CE-98 7 -..- CE-99 4-.- CE-9 8 4-8.8- CE-9A,-9 CE-9 CE-9A 7 98-89.- -849 - The No. // terminals are the internally common terminals. However, if possible, use the No. terminal for the input-side, and the No. terminal for the output-side. (Or, use them as solid.) It is not necessary to connect the No. terminal to. CE-98LC CE-9 7 7.-4.9.- 97-789.4 79.8- -4. Output current range (dual-output type) CE-9 CE-9 All specifications are subject to change without notice.
. CE-97,-994,-97,-99,-99 -. Connection diagram CE-97/CE-994 + 8 + + + Ci R R Co -. Output voltage setting To raise the output voltage, calculate R or R by assigning the absolute value of the output voltage to in the expression below, and attach it between the terminals to be connected. CE-97 9.- -. CE-97/CE-99/CE-99 + + C i 7 R R - Ci: External input capacitor (V, μf) Co: External output capacitor (Refer to specifications.) L: Load (electronic load module) -. Terminal assignments Terminal assignments Type No. No. No. No.4 No. No. No.7 No.8 CE-97 CE-994 + - + Co + CE-97 CE-99 CE-99 + - - CE-994 CE-97 CE-99 CE-99-8 -7-7 -7 R= R= R= R= - - - - 78. -4. To reduce the output voltage, calculate R or R by assigning the absolute value of the output voltage to in the expression below, and attach it between the terminals to be connected. CE-97 CE-994 CE-97 CE-99 CE-99-8 R=.4-9..- -78 - - - - - 78.-8-4. All specifications are subject to change without notice.
4 8 s max s max