Siemens AG 015 SITANS TH00 two-wire system, universal Overview Application SITANS TH00 transmitters can be used in all industrial sectors. Due to their compact size they can be installed in the connection head type B (DIN 479) or larger. The following sensors/signal sources can be connected over their universal input module: esistance thermometers (, or 4-wire system) Thermocouples esistance-based sensors and DC voltage sources The output signal is a direct current from 4 to 0 ma in accordance with the sensor characteristic. Transmitters of the "intrinsically safe" type of protection can be installed within potentially explosive atmospheres. The devices comply with the Directive 94/9/EC (ATEX), as well as FM and CSA regulations. Ultra flexible - with the universal SITANS TH00 transmitter Two-wire devices for 4 to 0 ma Mounting in the connection head of the temperature sensor Universal input for virtually any type of temperature sensor Configurable over PC Benefits Compact design Flexible mounting and center hole allow you to select your preferred type of installation Electrically isolated sockets for multimeters Diagnostics LED (green/red) Sensor open circuits and short-circuits Self- Configuration status stored in EEPOM SIL (with Order Code C0), SIL/ (with C) Expanded diagnostic functions, such as slave pointer, operating hours counter, etc. Special characteristic Electromagnetic compatibility to EN 1 and NE1 Function The SITANS TH00 is configured over a PC. A USB or S modem is linked to the output terminals for this purpose. The configuration data can now be edited using the SIPOM T software tool. The configuration data are then permanently stored in the non-volatile memory (EEPOM). Once the sensors and power supply have been correctly connected, the transmitter outputs a temperature-linear output signal and the diagnostics LED displays a green light. In the case of a sensor short-circuit, the LED flashes red, an internal device fault is indicated by a steady red light. The test socket can be used to connect an ammeter at any time for purposes and plausibility checks. The output current can be read without any interruption, or even without opening the current loop. SITANS TH00/TH00 () TC/ sensor A D μc1 (1) μc D A +1 4... 0 ma U aux, I out - Input A/D Sensors μc1 Analog-digital converter esistance thermometer, thermocouple, resistance-based sensor, mv sensor Microcontroller, secondary circuit Output μc D/A U aux I out Microcontroller, primary circuit Digital-analog converter Auxiliary power supply Output current (1) Electrically isolated () LED SITANS TH00 function diagram /8 Siemens FI 01 015 US Edition
Siemens AG 015 SITANS TH00 two-wire system, universal Technical specifications Input esistance thermometer Sensor type to IEC 0751 To JIS C 104; a = 0.009 K -1 to IEC 0751 Temperature Pt5 Pt1000 Pt5 Pt1000 Ni5 Ni1000 Special type over special characteristic (max. 0 points) Sensor factor 0.5... 10 (adaptation of the basic type, e.g. Pt100 to version Pt5... 1000) Units C or F Connection Standard connection 1 resistance thermometer () in -wire, -wire or 4-wire system Generation of average value identical resistance thermometers in -wire system for generation of average temperature Generation of difference identical resistance thermometers () in -wire system ( 1 or 1) Interface Two-wire system Parameterizable line resistance 100 (loop resistance) Three-wire system Four-wire system Sensor current 0.45 ma esponse time 50 ms for 1 sensor with opencircuit Open-circuit Always active (cannot be disabled) Short-circuit can be switched on/off (default value: ON) parameterizable (see table "Digital measuring errors") Min. measured 10 C (18 F) Temperature-linear or special characteristic esistance-based sensors Actual resistance Sensor type esistance-based, potentiometers Units Connection Normal connection 1 resistance-based sensor () in -wire, -wire or 4-wire system Generation of average value resistance-based sensors in -wire system for generation of average value Generation of difference resistance thermometers in -wire system (1 or 1) Interface Two-wire system Parameterizable line resistance 100 (loop resistance) Three-wire system Four-wire system Sensor current 0.45 ma esponse time 50 ms for 1 sensor with opencircuit Open-circuit Always active (cannot be disabled) Short-circuit can be switched on/off (default value: OFF) parameterizable max. 0... 00 (see table "Digital measuring errors") Min. measured 5... 5 (see Table "Digital measuring errors") esistance-linear or special characteristic Thermocouples Temperature Sensor type (thermocouples) Type B Pt0h-Pth to DIN IEC 584 Type C W5 %-e acc. to ASTM 988 Type D W %-e acc. to ASTM 988 Type E NiCr-CuNi to DIN IEC 584 Type J Fe-CuNi to DIN IEC 584 Type K NiCr-Ni to DIN IEC 584 Type L Fe-CuNi to DIN 4710 Type N NiCrSi-NiSi to DIN IEC 584 Type Pt1h-Pt to DIN IEC 584 Type S Pt10h-Pt to DIN IEC 584 Type T Cu-CuNi to DIN IEC 584 Type U Cu-CuNi to DIN 4710 Units C or F Connection Standard connection 1 thermocouple (TC) Generation of average value thermocouples (TC) Generation of difference thermocouples (TC) (TC1 TC or TC TC1) esponse time 50 ms for 1 sensor with opencircuit Open-circuit Can be switched off Cold junction compensation Internal With integrated Pt100 resistance thermometer External With external Pt100 IEC 0571 (-wire or -wire connection) External fixed Cold junction temperature can be set as fixed value Parameterizable (see table "Digital measuring errors") Min. measured Min. 40... 100 C (7... 180 F) (see table "Digital measuring errors") Temperature-linear or special characteristic mv sensor DC voltage Sensor type DC voltage source (DC voltage source possible over an externally connected resistor) Units mv esponse time 50 ms for 1 sensor with opencircuit Open-circuit Can be switched off -10... +70 mv-100 +1100 mv Siemens FI 01 015 US Edition /9
Siemens AG 015 SITANS TH00 two-wire system, universal Min. measured mv or 0mV Overload capability of the input -1.5... +.5 V DC Input resistance 1M Voltage-linear or special characteristic Output Output signal 4... 0 ma, -wire Auxiliary power 11... 5 V DC ((to 0 V for Ex ia and ib; to V for Ex na / nl / ic) Max. load (U aux 11 V)/0.0 A Overrange.... ma, infinitely adjustable (default range:.80 ma... 0.5 ma) Error signal (e.g. following sensor.... ma, infinitely adjustable fault) (conforming to NE4) (default value:.8 ma) Sample cycle 0.5 s nominal Damping Software filter 1st order 0... 0 s (parameterizable) Protection Against reversed polarity Electrically isolated Input against output (1 kv eff ) Measuring Digital measuring errors See table "Digital measuring errors" eference conditions Auxiliary power 4 V 1 % Load 500 Ambient temperature C Warming-up time > 5 min Error in the analog output (digital/analog converter) < 0.05 % of Error due to internal cold junction < 0.5 C (0.9 F) Influence of ambient temperature Analog measuring error 0.0 % of /10 C (18 F) Digital measuring errors - with resistance thermometers 0.0 C (0.11 F)/10 C (18 F) - with thermocouples 0. C (1.1 F)/10 C (18 F) Auxiliary power effect < 0.001 % of /V Effect of load impedance < 0.00 % of /100 Long-term drift In the first month < 0.0 % of After one year < 0. % of After 5 years < 0. % of Conditions of use Ambient conditions Ambient temperature range -40... +85 C (-40... +185 F) Storage temperature range -40... +85 C (-40... +185 F) elative humidity < 98 %, with condensation Electromagnetic compatibility acc. to EN 1 and NE1 Construction Material Molded plastic Weight 50 g (0.11 lb) Dimensions See "Dimensional drawings" Cross-section of cables Max..5 mm² (AWG 1) Degree of protection to IEC 059 Enclosure IP40 Terminals IP00 Certificates and approvals Explosion protection ATEX EC type test certificate "Intrinsic safety" type of protection "Operating equipment that is nonignitable and has limited energy" type of protection Explosion protection: FM for USA PTB 05 ATEX 040X II 1 G Ex ia IIC T/T4 II (1) G Ex ia/ib IIC T/T4 II (1) G Ex ia/ic IIC T/T4 II 1D Ex iad 0 T115 C II G Ex nl IIC T/T4 II G Ex na IIC T/T4 FM approval FM 0419 Degree of protection IS / Cl I, II, III / Div 1 / GP ABCDEFG T, T5, T4 Cl I / ZN 0 / AEx ia IIC T, T5, T4 NI / Cl I / Div / GP ABCDFG T, T5, T4 NI / Cl I / ZN / IIC T, T5, T4 Explosion protection to FM for Canada ( c FM US ) FM approval FM 0419C Degree of protection IS / Cl I, II, III / Div 1/ GP ABCDEFG T, T5, T4 NI / Cl I / DIV / GP ABCD T, T5, T4 NIFW / Cl I, II, III / DIV / GP ABCDFG T, T5, T4 DIP / Cl II, III / Div / GP FG T, T5, T4 Cl I / ZN 0 / Ex ia IIC T, T5, T4 Cl I / ZN / Ex na nl IIC T, T5, T4 Other certificates GOST, NEPSI, PESO, IEC, EXPOLABS Software requirements for SIPOM T PC operating system Windows ME, 000, XP, Win 7 and Win 8; can also be used in connection with S modem under Windows 95, 98 and 98SE Factory setting: Pt100 (IEC 751) with -wire circuit : 0... 100 C (... 1 F) Fault current:.8 ma Sensor offset: 0 C (0 F) Damping 0.0 s /10 Siemens FI 01 015 US Edition
Siemens AG 015 Digital measuring errors esistance thermometer Input Min. measured Digital C / ( F) C ( F) C ( F) to IEC 0751 Pt5-00... +850 10 (18) 0. (0.54) (-8... +15) Pt50-00... +850 10 (18) 0.15 (0.7) (-8... +15) Pt100... Pt00-00... +850 10 (18) 0.1 (0.18) (-8... +15) Pt500-00... +850 10 (18) 0.15 (0.7) (-8... +15) Pt1000-00... +50 10 (18) 0.15 (0.7) (-8... +) to JIS C104-81 Pt5-00... +49 10 (18) 0. (0.54) (-8... +100) Pt50-00... +49 10 (18) 0.15 (0.7) (-8... +100) Pt100... Pt00-00... +49 10 (18) 0.1 (0.18) (-8... +100) Pt500-00... +49 10 (18) 0.15 (0.7) (-8... +100) Pt1000-00... +50 10 (18) 0.15 (0.7) (-8... +) Ni 5... Ni1000-0... +50 10 (18) 0.1 (0.18) (-7... +48) esistance-based sensors Input Min. measured Digital esistance 0... 90 5 0,05 esistance 0... 00 5 0,5 SITANS TH00 two-wire system, universal Thermocouples Input Min. measured Digital C/( F) C ( F) C ( F) Type B 0... 180 100 (180) 1) (.0) 1) (... 08) Type C (W5) 0... 00 100 (180) (.0) (... 417) Type D (W) 0... 00 100 (180) 1 ) (1.80) ) (... 417) Type E -00... +1000 50 (90) 1 (1.80) (-8... +18) Type J -10... +100 50 (90) 1 (1.80) (-4... +19) Type K -0... +170 50 (90) 1 (1.80) (-8... +498) Type L -00... +900 50 (90) 1 (1.80) (-8... +15) Type N -00... +100 50 (90) 1 (1.80) (-8... +7) Type -50... +170 100 (180) (.0) (-58... +00) Type S -50... +170 100 (180) (.0) (-58... +00) Type T -00... +400 40 (7) 1 (1.80) (-8... +75) Type U -00... +00 50 (90) (.0) (-8... +111) 1) The digital in the range 0 to 00 C ( to 57 F) is C (5.4 F). ) The digital in the range 1750 to 00 C (18 to 417 F) is C (. F). mv sensor Input Measuring Min. measured Digital range mv mv V mv sensor -10... +70 40 mv sensor -100... +1100 0 400 The digital is the after the analog/digital conversion including linearization and calculation of the measured value. An additional error is generated in the output current 4 to 0 ma as a result of the digital/analog conversion of 0.05 % of the set (digital-analog error). The total error under reference conditions at the analog output is the sum from the digital error and the digital-analog error (poss. with the addition of cold junction errors in the case of thermocouple measurements). Siemens FI 01 015 US Edition /11
Siemens AG 015 SITANS TH00 two-wire system, universal Selection and Ordering data Article No. Temperature transmitter SITANS TH00 for installation in connection head, type B (DIN 479), two-wire system, 4... 0 ma, programmable, with electrical isolation Without explosion protection 7NG11-1NN00 With explosion protection -to ATEX 7NG11-1AN00 - to FM ( c FM US ) 7NG11-1BN00 Further designs Order code Add "-Z" to Article No. and specify Order code(s) With test protocol (5 measuring points) C11 Functional safety SIL C0 Functional safety SIL/ C Customer-specific programming Add "-Z" to Article No. and specify Order code(s) to be set Y01 1) Specify in plain text (max. 5 digits): Y01:... to... C, F Measuring point no. (TAG), max. 8 characters Y17 ) Measuring point descriptor, max. 1 characters Y ) Measuring point message, max. characters Y4 ) Pt100 (IEC) -wire, L = 0 U0 ) Pt100 (IEC) -wire U0 ) Pt100 (IEC) 4-wire U04 ) Thermocouple type B U0 )4) Thermocouple type C (W5) U1 )4) Thermocouple type D (W) U )4) Thermocouple type E U )4) Thermocouple type J U4 )4) Thermocouple type K U5 )4) Thermocouple type L U )4) Thermocouple type N U7 )4) Thermocouple type U8 )4) Thermocouple type S U9 )4) Thermocouple type T U0 )4) Thermocouple type U U1 )4) With TC: CJC external (Pt100, -wire) U41 With TC: CJC external with fixed value, specify Y50 in plain text Special differing customer-specific programming, Y09 5) specify in plain text Fail-safe value. ma (instead of,8 ma) U ) Cable extension W01 Transmitter with installed cable extension 00 mm (7.81 inch), for Pt100 in four-wire system Accessories Modem for SITANS TH100, TH00, T00 and TF with TH00 incl. SIPOM T parameterization software With USB connection MiniDVD for temperature measuring instruments With documentation in German, English, French, Spanish, Italian, Portuguese and SIPOM T parameterization software DIN rail adapters for head transmitters (Quantity delivered: 5 units) Connecting cable 4-wire, 150 mm, for sensor connections when using head transmitters in the high hinged cover (set with 5 units) Supply units see Chapter "Supplementary Components". Ordering example 1: 7NG11-1NN00-Z Y01+Y17+U0 Y01: -10... +100 C Y17: TICA1 Ordering example : 7NG11-1NN00-Z Y01+Y+U5 Y01: -10... +100 C Y: TICA14HEAT Factory setting: Pt100 (IEC 751) with -wire circuit : 0 100 C ( 1 F) Fault current:.8 ma Sensor offset: 0 C (0 F) Damping 0.0 s Article No. 7NG09-8KU A5E00451 7NG09-8KA 7NG09-8KC 1) For customer-specific programming for and TC, the start value and the end value of the required measuring must be specified here. ) For this selection, Y01 or Y09 must also be selected. ) For this selection, Y01 must also be selected. 4) Internal cold junction compensation is selected as the default for TC. 5) For customer-specific programming, for example mv and ohm, the start value and the end value of the required measuring and the unit must be entered here. /1 Siemens FI 01 015 US Edition
Siemens AG 015 SITANS TH00 two-wire system, universal Dimensional drawings Mounting on DIN rail Ø 44 (1.7) (1.0) (1) 4...0 ma (1) () 1 SIEMENS + 1 () () 4 -W 5 (4) SITANS TH00, mounting of transmitter on DIN rail 14 (0.55) 50.5 (1.99) (1.0) M4 x 0. (1.04) 59. (.5) 1(+) and (-) Auxiliary power supply U aux, output current I Out, 4, 5 and Pt100 sensor (for connections, see Sensor connection assignment) (+), (-) Measurement of the output current with a multimeter (1) terminal () Mounting screw M4x0 () LED for operation indication (4) Internal diameter of center hole. (0.5) DIN rail adapter, dimensions in mm (inch) SITANS TH00, dimensions and pin assignment, dimensions in mm (inch) Siemens FI 01 015 US Edition /1
Siemens AG 015 SITANS TH00 two-wire system, universal Schematics esistance thermometer esistance Thermocouple -W -W -W + TC - Two-wire system 1) Two-wire system 1) Cold junction compensation Internal/fixed value -W -W -W + TC - Three-wire system Three-wire system Cold junction compensation with external Pt100 in two-wire system 1) -W -W -W + TC - Four-wire system Four-wire system Cold junction compensation with external Pt100 in three-wire system -W -W -W + TC - + TC1-1 1 Generation of average value / difference 1) 1) Programmable line resistance for the purpose of correction. Generation of average value / difference 1) Generation of average value / difference with internal cold junction compensation Voltage measurement Current measurement Connection of auxiliary power supply (U aux ) -W -W U aux 4..0mA U I 1 SIEMENS + 1 5 SITANS TH00, sensor connection assignment /14 Siemens FI 01 015 US Edition