Specification Small Form Factor Pluggable SC Receptacle SFP ONU - Bidirectional Optical Transceivers 1000BASE-BX 1250Mbit/s TX 1490nm / RX 1310nm Ordering Information T B B S x C D 2 G A M Voltage / Temperature 1 : 3.3V / 0 ~ +70 2 : 3.3V / -40 ~ +85 Model Name Category Device Type Interface LOS Temperature Distance Latch Color TBB-S1CD2-GAM TBB-S2CD2-GAM W/O DDMI 1490nm DFB / 1310nm PIN AC / AC Coupling LVTTL +0 C~+70 C -40 C~+85 C 20km Orange Page 1
Features BiDi SC SFP Single Mode Transceiver Compliant with SFP MSA and SFF-8472 1490nm DFB Laser for transmitter and 1310nm PIN+TIA for receiver Hot-pluggable Single +3.3 Power Supply Complies with Telcordia (Bellcore) GR-468-CORE Typical data rate 1.25Gbps Maximal reach 20km RoHS-6 compliance Features Gigabit Ethernet Fiber Channel Routers, Hubs or Repeaters Absolute Maximum Ratings Storage temperature T S -40 85 C Input Voltage GND Vcc V Supply voltage V CC -0.5 3.6 V Operating Conditions Supply Voltage V CC 3.14 3.30 3.47 V Operating Case temperature ( TBB-S1CD2-GAM ) 0 +70 Tc Operating Case temperature ( TBB-S2CD2-GAM ) -40 +85 ºC Total Current ( Transmitter + Receiver ) Icc 300 ma Data Rate 1250 Mbps Page 2
Transmitter Specifications ( V CC =3.1V~3.5V;Tc= 0 o C~70 o C / Tc= -40 o C~85 o C ) Optical Characteristics Output Optical Power P out -9-3 dbm Extinction Ratio ER 9 db Center Wavelength λ C 1480 1490 1550 nm Side Mode Suppression Ratio SMSR 30 Spectral Width (-20dB) Δλ 1 nm Rise/Fall time (20-80%) T r,f 0.26 ns Output Eye Compliant with IEEE802.3z Electrical Characteristics Differential Input Impedance R DI 100 Ohm Differential Input Voltage V DI 0.50 2.40 V Tx Disable Input-High V DISH 2.0 V CC +0.3 V Tx Disable Input-Low V DISL 0 0.8 V Tx Fault Output-High V FOH 2.0 V CC +0.3 V Tx Fault Output-Low V FOL 0 0.8 V Receiver Specifications ( V CC =3.1V~3.5V;Tc= 0 o C~70 o C / Tc= -40 o C~85 o C ) Optical Characteristics Optical Input Power-maximum P SATIN -3 dbm Sensitivity (PRBS=2 7-1;BER 10-12 ) P SAN -23 dbm Operating Center Wavelength λ c 1260 1360 nm LOS Asserted P A -45 dbm LOS De-asserted P D -23 dbm LOS - Hysteresis P LH 0.5 5 db Electrical Characteristics Differential Output Impedance R DO 100 Ohm Differential Output Voltage V DO 0.37 2.00 V Rx LOS Output-High V LOSH 2.00 V CC +0.3 V Rx LOS Output-Low V LOSL 0.00 0.80 V Page 3
Pin Definition and Descriptions SFP Transceiver Electric Pad Layout Diagram of Host Board Connector Block Pin Numbers and Names Pin Function Definitions Pin No. Pin Name Function Note 1 V ee T Transmitter Ground 2 TX Fault Transmitter Fault Indication 1 3 TX Disable Transmitter Disable 2 4 MOD_DEF 2 Module Definition 2 3 5 MOD_DEF 1 Module Definition 1 3 6 MOD_DEF 0 Module Definition 0 3 7 Rate Select NC 8 LOS Loss of Signal 4 9 V ee R Receiver Ground 5 10 V ee R Receiver Ground 5 11 V ee R Receiver Ground 5 12 RD - Inv. Receiver Data Out 6 13 RD + Receiver Data Out 6 14 V ee R Receiver Ground 5 15 V CC R Receiver Power 7, 3.3V±5% 16 V CC T Transmitter Power 7, 3.3V±5% 17 V ee T Transmitter Ground 5 18 TD + Transmitter Data In 8 19 TD - Inv. Transmitter Data In 8 20 V ee T Transmitter Ground 5 Page 4
Notes: 1. TX Fault is an open collector/drain output, which should be pulled up with a 4.7K 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 2. TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 10 KΩ resistor. Its states are: Low (below 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (above 2.0v): Transmitter Disabled Open: Transmitter Disabled 3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K - 10KΩ resistor on the host board. The pull-up voltage shall be VccT or VccR Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID 4. LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K -10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5. VeeR and VeeT may be internally connected within the SFP module. 6. RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7. VccR and VccT are the receiver and transmitter power supplies. Maximum supply current is 300 ma. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1Ω should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage. When the recommended supply filtering network is used, hot plugging of the SFP transceiver module will result in an inrush current of no more than 30 ma greater than the steady state value. VccR and VccT may be internally connected within the SFP transceiver module. 8. TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. Page 5
Recommended Host Board Supply Filtering Network Suggest Transceiver / Host Interface 3.3V 10uF 0.1uF 1uH 1uH Protocol Vcc Protocol VCC SFP Modules VccT 0.1uF Tx_Disable Tx_Fault Tx_Disable Tx_Fault TD+ TD- 100 Laser Driver SerDes IC VeeT Protocol IC 10uF 0.1uF VccR RD+ 100 RD- Preamp& Quantizer Rx_LOS 3.3V Rx_LOS VeeR PLD/PAL MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) Serial ID Page 6
Mechanical Outlines (Unit:mm) Page 7