Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 TRC ELECTRONICS, INC. Dali PWM Signal Converter Mean Well DAP04 Series Ⅱ File Name:DAP04SPEC 0150907
Dali PWM Signal Converter Mean Well DAP04 Series TRC ELECTRONICS, INC. SPECIFICATION MODEL OUTPUT INPUT FUNCTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DAP04 NUMBER OF OUTPUT CHANNELS 4 OUTPUT SIGNAL PWM, 1KHz (Typ.) OUTPUT PWM LOGIC Active high or active low selectable by jumper ; Factory setting is active high DIMMING RANGE 1 100% VOLTAGE RANGE 90 305VAC 17 431VDC [DC input operation possible by connecting (), ()] FREQUENCY RANGE 47 63Hz AC CURRENT (Typ.) 0.1A INRUSH CURRENT (Typ.) COLD START 15A(t width=500 μs measured at 50% I peak) at 30VAC LEAKAGE CURRENT <0.5mA / 40VAC POWER CONSUMPTION (Typ.) 0.5W INPUT SIGNAL DALI or push dim RELAY SWITCH 40VAC / 8A, ON / OFF control refer to WORKING TEMP. 30 60 WORKING HUMIDITY 0 90% RH noncondensing STORAGE TEMP., HUMIDITY 40 80, 10 95% RH VIBRATION 10 500Hz, G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS EN613471, EN6134711, EN610581 Clause 8/17/0/5 approved DALI STANDARDS Comply with IEC6386101, 10, 07 WITHSTAND VOLTAGE I/PO/P:3.75KVAC ISOLATION RESISTANCE I/PO/P:>100M Ohms / 500VDC / 5 / 70% RH EMC EMISSION Compliance to EN55015, EN610003,3 EMC IMMUNITY Compliance to EN610004,3,4,5,6,8,11, EN61547 light industry level (surge KV), criteria A MTBF 46.9K hrs min. MILHDBK17F (5 ) DIMENSION 165*46*3mm (L*W*H) PACKING 0.16Kg; 84pcs/14.4Kgs/1.14CUFT File Name:DAP04SPEC 0150907
Dali PWM Signal Converter Mean Well DAP04 Series Block Diagram EMI FILTER AUX POWER PUSH DA DA PUSH DIM INTERFACE DALI INTERFACE MCU DIM DIM3 ACTIVE HIGH/LOW SELECT RY RY DIMMING OPERATION PUSH dim(primary side) Function No change of state Turn ONOFF Dimming up or down Setting light to 100% Pushing time <0.05 sec. 0.11 sec. 1.510 sec. >11 sec. Maximum length of the cable, from push button to last driver, is 0 meter. Factory default dimming setting : 100%. Every long pushing action will change the dimming direction. DALI interface(primary side) DALI protocol including 16 groups and 64 addresses. File Name:DAP04SPEC 0150907
Dali PWM Signal Converter Mean Well DAP04 Series Connection of Dimming Operation DALI Dimming solution : DAP04 with MEAN WELL's LED power supply MEAN WELL's AC/DC 1 V V DIM DIM Lamp 1... 4 V V DIM DIM... Lamp 4 Note: Choose a suitable cable for connecting the DAP04 and DALI controller and make sure the maximum voltage drop between these two units should not be higher than V. (Maximum cable length for 1.5mm cables is 300m.) Push Dimming Solution : DALI controller DALI Bus DAP04 with MEAN WELL's LED power supply DIM DA DA DIM3 DAP04 (DALIPWM signal converter) MEAN WELL's AC/DC Up to 4 channels 1 4 V V DIM DIM V V DIM DIM Lamp 1... Lamp 4 DIM PUSH Push dimmer DIM3 Up to 4 channels DAP04 (DALIPWM signal converter) Note: Only use Normally Open Push Button without light indicator. File Name:DAP04SPEC 0150907
Dali PWM Signal Converter Mean Well DAP04 Series Dimming with ON/OFF The DAP04 is equipped with a relay that can be used to turn ON/OFF MEAN WELL s. The relay is in the closed position when the generates dimming signal; the relay is in the open position when there is no output signal on the. RY V MEAN WELL V AC/DC DIM RY DIM Figure 1 DAP04 (DALIPWM signal converter ) An additional magnetic switch is needed when the total input current of the selected s is higher than 8A or used with s whose inrush current is greater than 50A, please refer to the figure. Relay or magnetic switch RY V MEAN WELL V AC/DC DIM RY DIM Figure DAP04 (DALIPWM signal converter ) File Name:DAP04SPEC 0150907
Dali PWM Signal Converter Mean Well DAP04 Series SYNCHRONIZATION OPERATION DAP04 provides 4channel outputs; every channel controls up to 0 units of MEAN WELL. The 4 channels can thus control up to 80 units of MEAN WELL. (Note. 1) The dimming percentage of the MEAN WELL s controlled by the same channel of DAP04 is the same. The dimming percentage per DAP04 channel can be controlled independently. The maximum allowable voltage drop between the DAP04 and s should not be higher than 0.5V. 0 drivers(max.) 0 drivers(max.) DIM DIM DIM DIM DIM DIM DIM DIM DIM DIM3 Up to 4 channels DAP04 (DALIPWM signal converter) Note. 1 : Light intensity of LEDs in the same group may be decreased when one of the s is AC OFF. File Name:DAP04SPEC 0150907
DALIPWM Signal Converter TRC ELECTRONICS, INC. Dali PWM Signal Converter Mean Well DAP04 Series DAP04 Mechanical Specification Case No.DAP04 Unit:mm 165 3 46 1 3 4 5 6 7 TB1 TB 1 3 4 5 6 7 8 JP1 1 Pin No. 1 3 4 5 6,7 Function PUSH DA DA RY / RY Description AC Line connection. AC Neutral connection. Dimming input. One pushbutton connected between the PUSH and. DALI Signal positive. DALI Signal negative. Relay contact rating(max.) : 40VAC / 8A resistive "Short" when output duty cycle >0 ; "Open" when output duty cycle=0 Function Description of TB Terminal Pin No. Assignment(TB1) Terminal Pin No. Assignment(TB) Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment 1 5 DA 1 5 DIM3 6 RY 6 DIM3 3 PUSH 7 RY 3 DIM 7 4 DA 4 DIM 8 Terminal Pin No. Assignment(JP1) Pin No. Assignment 1, ACTHI Function Description of TB1 Pin No. Function 1,3,5,7 DIM,4,6,8 DIM Description Dimming output Connect to DIM(Blue) line of dimmingable LED power. Dimming output Connect to DIM(White) line of dimmingable LED power. Function Description of JP1 Pin No. 1, Function ACTHI Description PWM active High / Low selection. Short : Active High. Open : Active Low. Factory setting is Active High. Installation Manual Please refer to : http://www.meanwell.com/search/dap04/dap04e.pdf File Name:DAP04SPEC 0150907