Universal Cabinet Leveling Base
MD00_A3 Universal Cabinet Leveling Base Creation Date 2015/10/05 Document Number SJ003A3 Rev A Description Universal Cabinet Leveling Base This manual is proprietary information of Lista International Corporation. Unauthorized reproduction of any portion of the manual is prohibited without consent of Lista International Corporation. The material in this manual is for informational purposes only. It is subject to change without notice. Lista International Corporation assumes no responsibility for any typographical errors contained in the manual. 2015 by Lista International Corporation. All rights reserved. 106 Lowland Street Holliston, MA 01746-2094 E-mail: sales@listaintl.com For questions or technical support, call 888 559 4441. Making Workspace Work is a registered trademark of Lista International Corporation. ISO 9001 Certified. ii Universal Cabinet Leveling Base
TABLE OF CONTENTS 1. Tools Required... 1 1.1 Safety Tools... 1 1.2 Standard Tools... 1 1.3 Standard Tools for Optional Components (Anchor Kit, and Side Skirt Assemblies):... 1 2. Components... 2 2.1 Optional Components... 2 3.... 4 3.1 Remove Drawers... 4 3.2 Leveling the Cabinet... 5 3.3 Re-Installing Drawers... 6 3.4 Installing Front/Rear Cover Assembly... 7 4. Optional Components Instructions... 9 4.1 Side Skirt Assembly... 9 4.2 Anchor Kit Assembly... 9 iii
NOTES iv Universal Cabinet Leveling Base
Tools Required 1. Tools Required 1.1 Safety Tools Protective eyewear Cut-resistant gloves 1.2 Standard Tools Level, 12 minimum length, 24 preferred length 5 / 16 Socket, ¼ drive 6 Socket Extension, ¼ drive Ratchet, ¼ drive Adhesive tape (to secure socket to the extension) Leveling base tool, Lista part number, LB-AT8 (purchased separately) Note: ¼ Socket and ratchet will be needed with this tool. 1.3 Standard Tools for Optional Components (Anchor Kit, and Side Skirt Assemblies): #1 Phillips Head Screwdriver; and 3 / 8 Diameter Anchoring bolt, not provided by LISTA, including: 7 / 16 Socket, ¼ drive Concrete Drill Concrete Drill Bit (see anchoring bolt instructions for size) 1
Components 2. Components (1) Leveling Base Channel (already installed) (1) ½-13 glides with a 5 / 16 hex head, already installed (4) Front Cover Assembly, in drawer, (1) Snap in Front Cover (1) Front Skirt Slider (1) 2.1 Optional Components Side Skirt Assembly (1) Side Skirt Plates (2) 10-32, Thread Forming Screws (4) Anchoring Kit Assembly (does not include anchoring bolt) (1) Anchor Brackets (2) Carriage Bolt, ¼-20 X 5 / 8 (2) 2 Universal Cabinet Leveling Base
¼-20 Washer (2) ¼-20 Kep Nut (2) Components Rear Cover Assembly (exact same items as the Front Cover Assembly, component 3) (1). Note: Side skirts and anchoring brackets cannot be placed in between cabinets that are bolted together. Instead install the side skirt/anchor bracket on the right side of the right-most cabinet and the left side of the left-most cabinet. 3
3. 3.1 Remove Drawers Warning: The inside edges of the cabinet may be sharp. Protective eyewear and cutresistant gloves are required to prevent injury. 1. Fully extend the bottom-most drawer, as illustrated in the following figure: 2. Unlock the gray tab on both sides of the drawer by sliding the gray tab towards the front of the cabinet, as illustrated in the following figure: 3. Slightly lift up on the front of the drawer and remove the drawer from the cabinet, as illustrated in the following figure: 4 Universal Cabinet Leveling Base
4. Push the carriages back into the housing. Or... To remove the carriages, bring them forward, push down on the clip in the rear of the carriage, and pull up and out of cabinet. 5. In the rear of the cabinet press on the flapper bar, to allow the next drawer to be removed. Locking and unlocking the cabinet will also move the flapper bar. 6. Repeat steps 1 thru 4 until a minimum of 12 (300 mm) of space is available. 3.2 Leveling the Cabinet 1. Find the highest point in the floor, install and level the cabinet that will be on the highest point in the floor, before leveling any other cabinets. 5
2. Locate the 4 glide location points: 2 Front, and 2 Rear. (Rear Glides are located behind the V notches in the rear stiffener as shown below). Warning: The inside edges of the cabinet may be sharp. Protective eyewear and cutresistant gloves are required to prevent injury. 3. Determine which corner is the highest using the level. 4. Adjust the three other glides by doing the following steps. 5. Secure the socket to the extension. 6. Insert the 5 / 16 socket and extension into the designated hole that needs to be adjusted (If purchased, substitute Leveling Base Tool LB-AT8 in steps 5 and 6). Note: Turning the socket clockwise will make rise the cabinet height, while turning the socket counter-clockwise will lower the cabinet height. 7. Adjust all glides as necessary to level cabinet. 8. If an anchoring kit is required, please see page 9, optional anchoring kit instructions, now. Otherwise continue to the next section, Re Installing Drawers. 3.3 Re-Installing Drawers Note: If installing cabinets side by side, do not re-install drawers until all cabinets have been placed, leveled and bolted together. 1. Pull out the suspension carriages on the bottom most drawers, verify the gray tabs are in unlock position (if carriages were removed, re-install by sliding the carriage member 6 Universal Cabinet Leveling Base
into the tracks on the side, push all the way in, then pull back out until a hard stop is reached). 2. Place the drawer in the track. 3. Push drawer in until it stops, lift the front of drawer slightly and begin pushing in again. 4. Pull the drawer out half way; push the gray tabs back into the locked position. This will lock the drawer in place. Note: Failure to do step 4 can result in a drawer failure which may cause injury. 5. Repeat steps 1 through 4 until all drawers have been re installed. 3.4 Installing Front/Rear Cover Assembly 1. Locate the Front Cover Assembly (Snap in Front Cover & Front Skirt Slider). 7
2. Place the front skirt slider inside the front cover, push until fully collapsed. 3. Install the front cover assembly by placing the left side of the cover into the slot on the base, and then push the right side in until it snaps into place. The skirt will drop down and be held by gravity. 8 Universal Cabinet Leveling Base
Optional Components Instructions 4. Optional Components Instructions 4.1 Side Skirt Assembly 1. Locate the side skirt assembly. 2. Install the side skirt using two, 10-32 self threading screws (phillips head). 3. Repeat step 1 and 2 for the remainder of the side skirts. 4.2 Anchor Kit Assembly 1. Locate the anchor kit assembly. 2. Install the bolt, washer and nut. Hand tighten the nut so that the bracket is not loose, but do not fully tighten at this point. 3. Mark the hole in the bottom of the bracket. 4. Remove the anchoring kit to allow for room to drill the floor. 5. Drill the marked location with the appropriate drill for the anchoring bolt. 6. Install anchoring bolt per manufacturer s instructions. 7. Install the anchoring bracket over the anchoring bolt and loosely tighten the nut. 8. Re-install hardware and tighten the anchor bolt nut and the carriage bolt nut. 9
Optional Components Instructions NOTES 10 Universal Cabinet Leveling Base
Optional Components Instructions NOTES 11
Storage & Workspace Systems was formed in January 2012 with the merger of two of the strongest brands in engineered storage and custom workspace applications STANLEY Vidmar and Lista International. Vidmar, acquired by The STANLEY Works in 1962, and Lista, a 2012 SBD acquisition, are the premier manufacturers of made-to-order modular cabinets in addition to a number of other powerful storage and workspace brands including STAK, Arlink, and Modula. Storage & Workspace Systems products serve multiple industries including Military and Government, Automotive, Manufacturing, Agricultural, Electronic and Laboratory applications. 106 Lowland St, Holliston, MA 01746 800-722-3020 Doc# sales@listaintl.com MD00_A3 2015 Lista International