CS601-Data Communication Latest Solved Mcqs from Midterm Papers

Similar documents
CS601 Data Communication Solved Objective For Midterm Exam Preparation

Data Communication (CS601)

CS601_MIDTERM_SOLVE_PAPER ( COMPOSED BY SADIA ALI SADII

6. has units of bits/second. a. Throughput b. Propagation speed c. Propagation time d. (b)or(c)

Digital to Digital Encoding

BSc (Hons) Computer Science with Network Security, BEng (Hons) Electronic Engineering. Cohorts: BCNS/17A/FT & BEE/16B/FT

COMPUTER COMMUNICATION AND NETWORKS ENCODING TECHNIQUES

DATA COMMUNICATION (CS601) FINAL TERM MEGA FILE

Basic Concepts in Data Transmission

Chapter 4 Digital Transmission 4.1

Signal Encoding Techniques

CHAPTER 5 TRANSMISSION OF DIGITAL DATA INTERFACES & MODEMS

ROM/UDF CPU I/O I/O I/O RAM

Data Communications Computer Eng. 3 rd class course Lecturer : Hamid Mousa

VTU QUESTION PAPER SOLUTIONS

Data Communications and Networking (Module 2)

Basic Communications Theory Chapter 2

BSc (Hons) Computer Science with Network Security BEng (Hons) Electronic Engineering

Introduction to Communications Part Two: Physical Layer Ch3: Data & Signals

SEN366 Computer Networks

Computer Networks MCQS MCQs Questions

Chapter 12: Digital Modulation and Modems

B.E SEMESTER: 4 INFORMATION TECHNOLOGY

BSc (Hons) Computer Science with Network Security. Examinations for Semester 1

Transmission Principles

Representation of Information. Transmission Principles. Agenda. Transmission of Information

DIGITAL COMMUNICATION

CTD600 Communication Trainer kit

Systems. Roland Kammerer. 29. October Institute of Computer Engineering Vienna University of Technology. Communication in Distributed Embedded

Sirindhorn International Institute of Technology Thammasat University

Unit aim. Telecommunication principles OCR unit number: 22. Level: 3 Credit value: 10 Guided learning hours: 80

Chapter 2: Fundamentals of Data and Signals

Chapter 5: Modulation Techniques. Abdullah Al-Meshal

Department of Computer Science and Engineering. CSE 3213: Communication Networks (Fall 2015) Instructor: N. Vlajic Date: Dec 13, 2015

Chapter 2. Physical Layer

Lecture-8 Transmission of Signals

2. By convention, the minimum and maximum values of analog data and signals are presented as voltages.

Digital signal is denoted by discreet signal, which represents digital data.there are three types of line coding schemes available:

EECE494: Computer Bus and SoC Interfacing. Serial Communication: RS-232. Dr. Charles Kim Electrical and Computer Engineering Howard University

Class 4 ((Communication and Computer Networks))

Chapter 5 Analog Transmission

ECT-215 Homework #1 Solution Set Chapter 14 Problems 1-29

DATA COMMUNICATION E-CONTENTS

Data Encoding g(p (part 2)

Downloaded from 1

Optical Fiber Communications p. 1 Introduction p. 1 History of Optical Fibers p. 1 Optical Fibers Versus Metallic Cable Facilities p.

CSCD 433 Network Programming Fall Lecture 5 Physical Layer Continued

King Fahd University of Petroleum & Minerals Computer Engineering Dept

EITF25 Internet Techniques and Applications L2: Physical layer. Stefan Höst

9.4. Synchronization:

Digital Transmission

Fundamentals of Data and Signals

UNIT TEST I Digital Communication

Chapter 4 Digital Transmission 4.1

Lecture 3 Concepts for the Data Communications and Computer Interconnection

Lecture Outline. Data and Signals. Analogue Data on Analogue Signals. OSI Protocol Model

CSCD 433 Network Programming Fall Lecture 5 Physical Layer Continued

Lecture (06) Digital Coding techniques (II) Coverting Digital data to Digital Signals

CS307 Data Communication

EEE 309 Communication Theory

Grundlagen der Rechnernetze. Introduction

Signal Encoding Techniques

Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)

Week 2 Lecture 1. Introduction to Communication Networks. Review: Analog and digital communications

EXPERIMENT WISE VIVA QUESTIONS

Review of Lecture 2. Data and Signals - Theoretical Concepts. Review of Lecture 2. Review of Lecture 2. Review of Lecture 2. Review of Lecture 2

CHAPTER 2 DIGITAL MODULATION

Ș.l. dr. ing. Lucian-Florentin Bărbulescu

Chapter 3 Data Transmission COSC 3213 Summer 2003

Communications I (ELCN 306)

(Refer Slide Time: 2:23)

Physical Layer, Part 2. Analog and Digital Transmission


Year : TYEJ Sub: Digital Communication (17535) Assignment No. 1. Introduction of Digital Communication. Question Exam Marks

Data Encoding. Two devices are used for producing the signals: CODECs produce DIGITAL signals MODEMs produce ANALOGUE signals

Chapter Two. Fundamentals of Data and Signals. Data Communications and Computer Networks: A Business User's Approach Seventh Edition

ITL Basics of Encoding and Wiring

QUESTION BANK SUBJECT: DIGITAL COMMUNICATION (15EC61)

Introduction to Telecommunications and Computer Engineering Unit 3: Communications Systems & Signals

11 Distinguish between low level and high level modulation. 12 What are the advantages of the super heterodyne receiver?

College of information Technology Department of Information Networks Telecommunication & Networking I Chapter DATA AND SIGNALS 1 من 42

EEE33350 Signals and Data Communications

Chapter 6 Bandwidth Utilization: Multiplexing and Spreading 6.1

Wireless Communications

COSC 3213: Computer Networks I: Chapter 3 Handout #4. Instructor: Dr. Marvin Mandelbaum Department of Computer Science York University Section A

CSE 123: Computer Networks Alex C. Snoeren. Project 1 out Today, due 10/26!

Telecommunications Principles

CPSC Network Programming. How do computers really communicate?

DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY CS6304- ANALOG AND DIGITAL COMMUNICATION BE-CSE/IT SEMESTER III REGULATION 2013 Faculty

Modulation. Digital Data Transmission. COMP476 Networked Computer Systems. Analog and Digital Signals. Analog and Digital Examples.

C06a: Digital Modulation

Outline / Wireless Networks and Applications Lecture 3: Physical Layer Signals, Modulation, Multiplexing. Cartoon View 1 A Wave of Energy

Qiz 1. 3.discrete time signals can be obtained by a continuous-time signal. a. sampling b. digitizing c.defined d.

Department of Computer Science and Engineering. CSE 3213: Computer Networks I (Fall 2009) Instructor: N. Vlajic Date: Dec 11, 2009.

Digital Modulation Lecture 01. Review of Analogue Modulation Introduction to Digital Modulation Techniques Richard Harris

Objectives. Presentation Outline. Digital Modulation Lecture 01

Level 6 Graduate Diploma in Engineering Communication systems

Hello and welcome to today s lecture. In the last couple of lectures we have discussed about various transmission media.

Fundamentals of Digital Communication

NETWORKS FOR EMBEDDED SYSTEMS. (Data Communications and Applications to Automotive)

Transcription:

CS601-Data Communication Latest Solved Mcqs from Midterm Papers May 07,2011 Lectures 1-22 Moaaz Siddiq Latest Mcqs MIDTERM EXAMINATION Spring 2010 Question No: 1 ( Marks: 1 ) - Please choose one Effective network mean that the network has fast delivery, timeliness and high bandwidth duplex transmission accurate transmission (P6) low bandwidth Question No: 2 ( Marks: 1 ) - Please choose A set of devices connected by communication links is called networking True (P12) Question No: 3 ( Marks: 1 ) - Please choose one Which one best describes the given statement: "To allow multiple users to share total capacity of a transmission medium" congestion control exchange management multiplexing (P17) Question No: 4 ( Marks: 1 ) - Please choose one Line configuration refers to the way two or more devices attach to a. Link (P25) Circuit Route Node Question No: 5 ( Marks: 1 ) - Please choose one requires the maximum number of I/O ports. Bus Star

Mesh Ring (P29) Question No: 6 ( Marks: 1 ) - Please choose one is used to define the direction of the signal flow between the linked devices. transmission mode (P34) transmission method transmission impairments Question No: 7 ( Marks: 1 ) - Please choose one Unidirectional traffic movement is overcome by dual ring technology. True (P33) Question No: 8 ( Marks: 1 ) - Please choose one Trailer is only added at layer of OSI model. Data link Physical Network Application (P41) Question No: 9 ( Marks: 1 ) - Please choose one Data link layer deals with mechanical and electrical specifications of transmission medium and interface True (P44) Question No: 10 ( Marks: 1 ) - Please choose one A signal that repeats a pattern over a regular interval of time is called. periodic signal analog signal composite signal (P58) Question No: 11 If there is ( Marks: 1 ) - Please choose one in voltage then the frequency is infinite. instantaneous change continuous change no change (P61) Question No: 12 ( Marks: 1 ) - Please choose one

In a time-domain plot, the horizontal axis is measure of. signal amplitude frequency phase time (P63) Question No: 13 ( Marks: 1 ) - Please choose DC component is also termed as Direct current component or a component with non-zero frequency. True (P72) Question No: 14 ( Marks: 1 ) - Please choose one Quantization means measuring amplitudes of signal at equal intervals. True (P80) Question No: 15 ( Marks: 1 ) - Please choose one Amplitude in ASK is more resistive to EMI and Noise. True (P87) Question No: 16 ( Marks: 1 ) - Please choose one ASK, PSK, FSK and QAM are examples of modulation. digital-to-digital digital-to-analog (P85) analog-to-analog analog-to-digital Question No: 17 ( Marks: 1 ) - Please choose one The bit rate always equals the baud rate in which type of signal? FSK QAM 4-PSK PSK (P86) Question No: 18 ( Marks: 1 ) - Please choose one Asynchronous transmission is

Slow (P99) costly non-effective fast Question No: 19 A ( Marks: 1 ) - Please choose one converts an analog signal into a digital signal. Demodulator (P110) Modulator Digital-to-analog converter Question No: 20 ( Marks: 1 ) - Please choose one If a station does not receive its signal up to a specified time that system issues an alarm to another node (P188) network manager switch network analyzer MIDTERM EXAMINATION Spring 2010 Question No: 1 ( Marks: 1 ) - Please choose one The information to be communicated in a data communications system is the Medium Protocol Message (P 7) Transmission Question No: 2 ( Marks: 1 ) - Please choose one Which is not an element of protocol semantics timing communication service module (P19)

Question No: 3 ( Marks: 1 ) - Please choose one Line configuration refers to the way two or more devices attach to a. Link (P 25) Circuit Route Node Question No: 4 ( Marks: 1 ) - Please choose one requires the maximum number of I/O ports. Bus Star Mesh (P29) Ring Question No: 5 ( Marks: 1 ) - Please choose one Which topology requires a central controller or hub? Mesh Star (P 30) Bus Ring Question No: 6 ( Marks: 1 ) - Please choose one Layers 5, 6 and 7 also called as network support layers. False (P 42)

Question No: 7 ( Marks: 1 ) - Please choose one Internet with small i specifies the world wide Network the actual internet. False (P 39) Question No: 8 ( Marks: 1 ) - Please choose one Data link layer deals with mechanical and electrical specifications of transmission medium and interface (P 44) False Question No: 9 ( Marks: 1 ) - Please choose one Data synchronization is a function related with session layer (P 51) presentation layer transport Question No: 10 ( Marks: 1 ) - Please choose one OSI model was developed prior to TCP/IP model. (P 54) False Question No: 11 ( Marks: 1 ) - Please choose one Fourier transform tells us that any digital signal can be decomposed into infinite number of periodic signals False (P58)

Question No: 12 ( Marks: 1 ) - Please choose one A signal that repeats a pattern over a regular interval of time is called. periodic signal (P58) analog signal composite signal Question No: 13 ( Marks: 1 ) - Please choose one Frequency band in which 99% of the total power resides is called power bandwidth (P 67) half power bandwidth 3dB bandwidth F.M. Question No: 14 ( Marks: 1 ) - Please choose one In differential Manchester we require two transition or signal changes to represent binary zero one (P76) both zero and one Question No: 15 ( Marks: 1 ) - Please choose one In Alternate mark inversion the term mark comes from telegraphy (P77) telephony digital telephony

Question No: 16 ( Marks: 1 ) - Please choose one A 56k modem can download at a rate of Kbps and upload at a rate of Kbps. 33.6: 33.6 33.6: 56.6 56.6: 33.6 56.6: 56.6 Question No: 17 ( Marks: 1 ) - Please choose one The bit rate always equals the baud rate in which type of signal? FSK (P 86) QAM 4-PSK PSK Question No: 18 ( Marks: 1 ) - Please choose one Asynchronous transmission is slow (P 99) costly non-effective fast Question No: 19 ( Marks: 1 ) - Please choose one

At the layer, a DCE takes data generated by a DTE. physical (P 101) transport data link application Question No: 20 ( Marks: 1 ) - Please choose one requires more bandwidth. FSK ASK (P 112) PSK QAM Question No: 1 ( Marks: 1 ) - Please choose one Which topology requires a central controller or hub? Mesh Star (P 30) Bus Ring MIDTERM EXAMINATION Spring 2010 Question No: 2 ( Marks: 1 ) - Please choose one Unidirectional traffic movement is overcome by dual ring technology. (P33) False

Question No: 3 ( Marks: 1 ) - Please choose one Which one best describes the given statement: "To allow multiple users to share total capacity of a transmission medium" congestion control exchange management multiplexing (P17) Question No: 4 ( Marks: 1 ) - Please choose one Which one is not among standard creation committee. internet society and IETF (P 24) ITU-T IEEE Question No: 5 ( Marks: 1 ) - Please choose one Set of rules that govern communication is called OSI model Protocol (P 8) TCP/IP model Datagram Question No: 6 ( Marks: 1 ) - Please choose one Frequency of a failure and network recovery time after a failure is measures of the of a network. Performance (P 14) Reliability Security Feasibility

Question No: 7 ( Marks: 1 ) - Please choose one 3dB is also called as power bandwidth. False (P66) Question No: 8 ( Marks: 1 ) - Please choose one ASK, PSK, FSK and QAM are examples of modulation. digital-to-digital digital-to-analog (P85) analog-to-analog analog-to-digital Question No: 9 ( Marks: 1 ) - Please choose one Packet switching is a connection oriented service. False (P38) Question No: 10 ( Marks: 1 ) - Please choose one Data synchronization is a function related with session layer (P51) presentation layer transport

Question No: 11 ( Marks: 1 ) - Please choose one Fourier transform tells us that any digital signal can be decomposed into infinite number of periodic signals False (P 58) Question No: 12 ( Marks: 1 ) - Please choose one The internet model consists of layers. three (P239) two five seven Question No: 13 ( Marks: 1 ) - Please choose one Analog to digital conversion is also termed as modulating an analog signal. False (P 77) Question No: 14 ( Marks: 1 ) - Please choose one PCM is the first process of PAM. False (P80)

Question No: 15 ( Marks: 1 ) - Please choose one A modulator converts a(n) signal to a(n) signal. FSK: PSK Digital: analog (P 110) Analog: digital PSK: FSK Question No: 16 ( Marks: 1 ) - Please choose one The layer changes bits into electromagnetic signals. physical data link transport none of given http://www.ee.surrey.ac.uk/projects/cal/networks/physical_layer.htm Question No: 17 ( Marks: 1 ) - Please choose one We need to decompose a composite signal into its components. fourier transform (P 64) nyquist theorem shannon capacity Question No: 18 ( Marks: 1 ) - Please choose one The bit rate always equals the baud rate in which type of signal? FSK (P 86) QAM

4-PSK PSK Question No: 19 ( Marks: 1 ) - Please choose one There are possible variations of 16 QAM. five two three (P93) four Question No: 20 ( Marks: 1 ) - Please choose one Number of signal units per second that are required to represent a bit is called bit rate. False (P 68) MIDTERM EXAMINATION Spring 2010 Please choose one ( Marks: 1 ) Effective network mean that the network has fast delivery, timeliness and high bandwidth duplex transmission accurate transmission (P6) low bandwidth Question No: 2 ( Marks: 1 ) - Please choose one A set of devices connected by communication links is called networking True (P12)

Question No: 3 ( Marks: 1 ) - Please choose one is a multipoint topology. Ring Mesh Tree Bus Question No: 4 ( Marks: 1 ) - Please choose one requires the maximum number of I/O ports. Bus Star Mesh Ring (P29) Question No: 5 ( Marks: 1 ) - Please choose one Unidirectional traffic movement is overcome by dual ring technology. True (P33) Question No: 6 ( Marks: 1 ) - Please choose one As the data packet moves from the lower to the upper layers, headers are. added subtracted rearranged modified Question No: 7 ( Marks: 1 ) - Please choose one Data chunk at data link layer is called frame packet (P38) datagram Question No: 8 ( Marks: 1 ) - Please choose one The layer is the layer closest to the transmission medium. Physical (P45) data link network transport Question No: 9 ( Marks: 1 ) - Please choose one Data synchronization is a function related with session layer (P 51) presentation layer transport

Question No: 10 ( Marks: 1 ) - Please choose one Which layer is responsible for source to destination delivery of entire message? transport layer (P59) network layer session layer application layer Question No: 11 ( Marks: 1 ) - Please choose one Encryption and encoding are the same terms. True (P52) Question No: 12 ( Marks: 1 ) - Please choose one TCP/IP model Application layer incorporate OSI Application and presentation layers True Question No: 13 ( Marks: 1 ) - Please choose one A sine wave must be an analog signal. True (P58) Question No: 14 ( Marks: 1 ) - Please choose one A periodic signal can always be decomposed into exactly an odd number of sine waves a set of sine waves set of sine waves, one of the which must have a phase of 00 none of the given (P58) Question No: 15 ( Marks: 1 ) - Please choose one Manchester is a type of encoding. Biphase (P75) polar biphase & polar none of the given Question No: 16 ( Marks: 1 ) - Please choose one The powerful carrier signal is called as the carrier frequency (P86) base signal carrier frequency and base signal none of given

Question No: 17 ( Marks: 1 ) - Please choose one Modulation of an analog signal can be accomplished through changing the of the carrier signal. amplitude frequency phase all of the given (P58) Question No: 18 ( Marks: 1 ) - Please choose one In transmission, bits are transmitted over a single wire, one at a time. Asynchronous serial Synchronous serial Parallel (P99) Asynchronous & Synchronous serial Question No: 19 ( Marks: 1 ) - Please choose one In RS 422 Balanced mode two lines carry signals which are not identical to each other. Same (P109) different digital analog Question No: 20 ( Marks: 1 ) - Please choose one A converts an analog signal into a digital signal. Demodulator (P110) Modulator Digital-to-analog converter MIDTERM EXAMINATION Spring 2009 Question No: 1 ( Marks: 1 ) - Please choose one In RS 422 Balanced mode two lines carry signals which are not identical to each other. same (P109) different digital analog Question No: 2 ( Marks: 1 ) - Please choose one The generates the data and passes it along with any control information to a. DTE; DCE (P 101) DCE; DTE DCE; node DTE; application

Question No: 3 ( Marks: 1 ) - Please choose one In transmission, a start bit and a stop bit frame a character byte. Asynchronous serial (P99) Synchronous serial (P99) Parallel Asynchronous & Synchronous serial Question No: 4 ( Marks: 1 ) - Please choose one In transmission, bits are transmitted simultaneously, each across its own wire. Asynchronous serial Synchronous serial Parallel Asynchronous & Synchronous serial Question No: 5 ( Marks: 1 ) Asynchronous transmission is slow (P99) costly non-effective fast - Please choose one Question No: 6 ( Marks: 1 ) - Please choose one In transmission the timing of the signal is unimportant. Asynchronous (P99) Synchronous Polar Bi-polar Question No: 7 ( Marks: 1 ) - Please choose one In 8QAM each signal shift or one baud represents 4 bits 2 bits 5 bits 3 bits (P93) Question No: 8 ( Marks: 1 ) - Please choose one PCM is the first process of PAM. False Question No: 9 ( Marks: 1 ) - Please choose one Bi phase encoding is a type of bipolar encoding in which we use two voltage levels. (P73) False

Question No: 10 ( Marks: 1 ) - Please choose one The amplitude of a digital signal depends upon the phase voltage wavelength to represent a bit. Question No: 11 ( Marks: 1 ) - Please choose one Time domain plot show changes in signal phase with respect to time. False (P63) Question No: 12 ( Marks: 1 ) - Please choose one OSI model was developed prior to TCP/IP model. False(P54) Question No: 13 ( Marks: 1 ) - Please choose one layer is the layer closest to the transmission medium. Physical (P45) Data link Network Transport Question No: 14 (Marks: 1) - Please choose one Data chunk at data link layer is called frame packet (P38) datagram Question No: 15 ( Marks: 1 ) The internet model consists of Three (P239) Two Five Seven - Please choose one layers. Question No: 16 ( Marks: 1 ) - Please choose one representation of links that connect nodes is called as physical topology. geometrical (P28) logical physical

Question No: 17 ( Marks: 1 ) is a multipoint topology. Ring Mesh Tree Bus (P31) - Please choose one Question No: 18 ( Marks: 1 ) - Please choose one In mesh topology, if there are five nodes then there will be 5 10(P10) 15 20 links. Question No: 19 (Marks: 1) - Please choose one Non proprietary standard is also termed as de facto standard. (P23) False Question No: 20 ( Marks: 1 ) - Please choose one Effective network mean that the network has fast delivery, timeliness and high bandwidth duplex transmission accurate transmission (P6) low bandwidth MIDTERM EXAMINATION Spring 2009 Question No: 1 (Marks: 1) - Please choose one Frequency of a failure and network recovery time after a failure is measures of the of a network. Performance (P 14) Reliability Security Feasibility

Question No: 2 (Marks: 1) - Please choose one Secondary hub in a tree must be a passive hub. True (P31) Question No: 3 (Marks: 1) - Please choose one In mesh topology, if there are five nodes then there will be links. 5 10 (P29) 15 20 Question No: 4 (Marks: 1) - Please choose one Internet with small i specifies the world wide Network the actual internet. True (P39) Question No: 5 (Marks: 1) - Please choose one Data link layer deals with mechanical and electrical specifications of transmission medium and interface True (P 44) Question No: 6 (Marks: 1) - Please choose one When data are transmitted from device A to device B, the header from A s layer 4 is read by B s layer. physical transport application none of the given Question No: 7 (Marks: 1) - Please choose one Time domain plot show changes in signal phase with respect to time. True (63) Question No: 8 (Marks: 1) - Please choose one Frequency band in which 99% of the total power resides is called power bandwidth (P67) half power bandwidth F.M.

Question No: 9 (Marks: 1) - Please choose one The inversion of the level at 1 bit is called as NRZ-L NRZ-I (P73) RZ Question No: 10 (Marks: 1) - Please choose one Which of the encoding schemes have bandwidth problems? Differential Manchester AMI (P77) RZ Question No: 11 (Marks: 1) - Please choose one Bi phase and bipolar are same terms. True (P78) Question No: 12 (Marks: 1) - Please choose one Quantization means measuring amplitudes of signal at equal intervals. True (P80) Question No: 13 (Marks: 1) - Please choose one The last process in PCM is digital data into digital signal. Encoding (P70) decoding modulating Question No: 14 (Marks: 1) - Please choose one Which modulation technique involves tribits, eight different phase shifts, and one mplitude? FSK 8-PSK ASK 4-PSK Question No: 15 (Marks: 1) - Please choose one Asynchronous transmission is slow (P99) costly non-effective fast Question No: 16 (Marks: 1) - Please choose one Synchronous transmission have. a start bit a stop bit gaps between bytes none of the given (P99)

Question No: 17 (Marks: 1) - Please choose one Asynchronous transmission The generates the data and passes it along with any control information to a. DTE; DCE (P101) DCE; DTE DCE; node DTE; application Question No: 18 (Marks: 1) - Please choose one A human brain is considered as a driver machine DTE (P101) DCE Question No: 19 (Marks: 1) - Please choose one The last modified version of EIA-232 standard is EIA-232 D (P102) EIA-232 A EIA-232 B EIA-232 C Question No: 20 (Marks: 1) - Please choose one A converts an analog signal into a digital signal. Demodulator (P110) Modulator Digital-to-analog converter Moaaz.pk@gmail.com