Assemly Instrutions-C1 Amphenol UG STANDARD SOLDER TYPE PLUGS 83-1SP, 83-1SP-1050, 83-1SP-15RFX, 83-822 oupling ring plug su-ssemly Amphenol Connetor Cle Atthment Dt Stripping Dimensions, inhes (mm) Numer Type RG-/U Outer Inner 83-1SP-1050 Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) 83-1SP Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) 83-1SP-15RFX Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.13(28.6).689(17.5).625(15.9) 83-822 Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder 1.25(31.8).687(17.4).625(15.9) 83-59 Angle Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder.844(21.4).391(9.9).250(6.4) 83-67 Angle Plug 8, 9, 11, 213, 214, 63, 87A, 225 Solder Solder.844(21.4).391(9.9).250(6.4) A B C Slide oupling ring onto le. Cut end of le even nd strip jket, rid nd dieletri to dimensions shown in tle. All uts re to e shrp nd squre. Do not nik rid, dieletri or enter ondutor. Tin exposed enter ondutor nd rid, voiding exessive het. SOLDER solder HERE here Srew the plug su-ssemly on le. Solder ssemly to rid through solder holes, mking good ond etween rid nd shell. Solder ondutor to ontt. Do not use exessive het. For finl ssemly on stright plugs, move oupling ring forwrd nd srew in ple on plug su-ssemly. 274
Assemly Instrutions-C2 Amphenol UG STANDARD SOLDER TYPE WITH REDUCING ADAPTER FOR PLUGS 83-1SP, 83-1SP-1050, 83-1SP-15RFX, 83-822, USING 83-168 83-168-RFX, OR 83-185, 83-185-RFX REDUCING ADAPTER oupling ring 83-168 or 83-168-RFX for RG-59 plug su-ssemly 83-185 or 83-185-RFX for RG-58 reduing dpter Cle RG-/U Cle RG-/U Atthment Dt Using 83-168 or 83-185 Using 83-168-RFX or 83-185-RFX Amphenol Connetor (using 83-168 (using 83-185 Numer Type Stripping Dims, inhes (mm) Stripping Dims, inhes (mm) or 83-168-RFX) or 83-185-RFX) Outer Inner 83-1SP Plug 59 58 Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-1SP-1050 Plug 59 58 Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-1SP-15RFX Plug 59 58 Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-750 Plug 59 58 Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) 83-822 Plug 59 58 Solder Solder.750(19.1).375(9.5).625(15.9).689(17.5).375(9.5).551(14.0) Assemly A B Slide oupling ring nd dpter onto le. Cut end of le even nd strip jket to dimension shown in tle. C Position dpter flush with end of le jket. Fn rid slightly nd fold k over ody of dpter s shown. Press rid down over ody nd trim to dimension. Bre ondutor to dimension shown in tle. Tin exposed enter ondutor nd rid, voiding exessive het. solder SOLDER HERE here Srew plug su-ssemly onto dpter. Solder rid to shell through solder holes, mking good ond etween rid nd shell. Solder ondutor to ontt. Do not use exessive het. Step 4 STEP 4 Step 4 For finl ssemly, srew oupling ring onto plug su-ssemly. 275
Assemly Instrutions-C4, C5 Amphenol C4 BRAID CRIMP - SOLDER CENTER CONTACT ferrule oupling nut ody ssemly Amphenol Connetor Cle Cle Atthment Hex Crimp Dt Stripping Dims, inhes (mm) Numer Type RG-/U Cvity for Die Set CTL Series Outer Inner Outer Ferrule Tool 227-994 Tool No. 83-58SP Plug 58, 141 Crimp Solder.213(5.4) 227-1221-11 CTL-1 1.14(29.0).780(19.9).250(6.4) 83-58SP-1002 Plug 400 Crimp Solder.213(5.4) 227-1221-11 CTL-1 1.14(29.0).780(19.9).250(6.4) 83-59DCP-RFX Plug 59 Crimp Solder.255(6.5) 227-1221-13 CTL-1 1.22(30.9).574(22.6).543(13.8) 83-58SCP-RFX Plug 58 Crimp Solder.213(5.4) 227-1221-11 CTL-1 1.22(30.9).574(22.6).543(13.8) 83-59SP Plug 59 Crimp Solder.255(6.5) 227-1221-13 CTL-1 1.22(30.9).574(22.6).543(13.8) 83-8SP-RFX Plug 8 Crimp Solder.429(10.9) 227-1221-25 CTL-3 1.22(30.9).574(22.6).543(13.8) A B C Cut end of le even. Strip le to dimensions shown in tle. All uts re to e shrp nd squre. Do not nik rid, dieletri or enter ondutor. Tin enter ondutor voiding exessive het. BRAID rid AFTER fter FLARINGflring ody ssemly BODY ASSEMBLY Slide oupling nut nd ferrule over le jket. Flir rid slightly s shown. Instll le into ody ssemly, so inner ferrule portion slides under rid, until rid utts shoulder. Slide outer ferrule over rid until it utts shoulder. Crimp ferrule with tool nd die set indited in tle. Soft solder enter ondutor to ontt. Avoid heting ontt exessively to prevent dmging insultor. Slide/srew oupling nut over ody. C5 CRIMP-CRIMP TYPE-C5 outer ferrule oupling nut ody ssemly Cle Atthment Hex Crimp Dt CTL Die Set Amphenol Connetor Cle Numer Type RG-/U Cvity for Cvity for Cvity for Series for Tool Outer Inner Outer ferrule End of Ferrule Center Contt Tool # 227-944 83-58DCP-2 Plug 58 Crimp Crimp.260(6.60).210(5.33).052(1.32) sq. 1.23(31.3).791(20.2).25(6.35) 227-1350 83-58DCP-2RFX Plug 58 Crimp Crimp.255(6.5).213(5.4).068(1.7) 1.12(28.4).685(17.4).236(5.99) CTL-1 227-1221-11,-13 1.23 (31.3).791 (20.2).250 (6.4) Strip le to dimensions shown. Slide ferrule nd oupling nut over le jket nd flir rid slightly s shown. rid BRAID AFTER fter FLARINGflring ody ssemly CRIMP (3) rimp (3) CRIMP (1) rimp (2) CRIMP (2) rimp Slide ody ssemly into ple so inner ferrule portion slides under rid. Brid must utt k of ody. Slide oupling nut forwrd. Slide ferrule over rid until it utts ginst ody. Using tools indited in tle ove: (1) rimp enter ontt (2) rimp outer ferrule to rid (3) rimp outer ferrule to le jket 276
Assemly Instrutions-C6 Amphenol FCP TERMINATION FOR PLUGS 83-58FCP, 83-58FCP-RFX on RG-58 BARB r enter CENTER CONTACT ontt shoulder SHOULDER ferrule oupling nut ody ssemly TIP tip Amphenol Connetor Cle Stripping Dimensions, inhes (mm) Tools Numer Type RG-/U 83-58FCP FCP Plug 58 Pliers & Fier Grommet in Bg 1.00(25.4).812(20.6).500(12.7) 83-58FCP-RFX FCP Plug 58 Pliers & Fier Grommet in Bg.673(17.0).547(14.0).236(6.0) Assemly A B C Strip le to dimensions shown in tle. rid BRAID AFTER fter FLARINGflring Slide ferrule nd oupling nut over le. Flir rid slightly. Insert ody under flred rid until shoulder is ginst le jket. rid BRAID trim ondutor fter ssemly TRIM CONDUCTOR AFTER ASSEMBLY Slide nut onto ody. Grsp le. Push ferrule over r nd up ginst ody. Crimp tip of enter ontt with pliers, or if you prefer, solder. Then trim enter ondutor even with end of ontt. 277
Assemly Instrutions-C7 Amphenol HOODS FOR ADAPTING PANEL RECEPTACLES TO COAXIAL CABLES 83-1H (UG-106/U) for RG-8, 10, 11, 12, 63, 79, 115, 149, 213, 215 83-765 (UG-177/U) for RG-58, 141 83-765 83-765 83-1H 83-1H Amphenol Connetor Cle Cle Atthment Stripping Dimensions Numer Type RG-/U Outer Inner 83-1H Hood 8, 10, 11, 12, 63, 79, 115, 149, 213, 205 Solder Solder.625(15.8).500(12.7).312(7.92) 83-765 Hood 58, 141 Solder Solder.750(19.0).687(17.4).312(7.92) Strip le to dimensions shown. Do not nik enter ondutor. Tin exposed rid nd enter ondutor. SOLDER solder CABLE CENTER le enter ondutor CONDUCTOR INTO SOLDER CUP TERMINAL into solder up terminl Slide hood over rid. When using doule-rided le, hood goes over inner rid only. Then, in step 3, solder outer rid to outside of hood. Solder Center Condutor into solder up terminl. tpe or tuing over this setion TAPE OR TUBING OVER THIS SECTION TACK SOLDER FLANGES TOGETHER tk solder flnges together Slide hood flush ginst reeptle nd tk-solder hood flnge to reeptle flnge. Solder hood to rid s shown. Use tpe or tuing over setion shown. solder here for 83-765 SOLDER HERE FOR 83-765 ALL AROUND BACK OF HOOD SOLDER solder HERE FOR here 83-1H for 83-1H THREE SOLDER HOLES three solder holes 278