MOTO / PUMP POTETI ELAS These relays are useful for protection of 3-phase A induction motors against various hazards. With their unique advantages they eliminate use of a thermal/bimetal relay for motor protection. eing current sensing, they are to be selected according to motor rating and are available for practically all ranges of motors. These relays are ideally suitable for Air-conditioning ompressor motor protection, as also for motors in machines, conveyors, cranes/hoists and lifts, and for pumps. MODELS MP D2, SPG D2, F3 D1, D2 MP1, D2MP2, TS1, MMP, M-ommander, WT D1, W FEATUES Fixed/adjustable unbalance settings Fixed/adjustable settings for under/over voltage, current, load Fixed/adjustable trip delays esetting Auto or Output contacts : 1 O or 2 O hoice of enclosures (DI-ail, Flush) Models with Micro-ontroller based design Serial ommunication (S485) port 2 line alpha-numeric LD display Use of SMD Technology User-friendly LED indications POTETIS / FUTIS ure (Phase Loss/Single Phasing), Phase sequence reversal, Voltage Unbalance, Under Voltage, Over Voltage Overload protection as per motor characteristics o-load/dry running Winding overheating Over-current/Short circuit/locked rotor Earth Fault Ordering Instructions Product Family ame Model ame System & frequency Aux. Supply/ontrol supply voltage /Pump rating (HP/KW) & duty Overload characteristics required o. of PTs & Temp. graph 23
M O T O / P U M P P O T E T I O E L A S MP D2 Overload Protection elay with ure SPG D2 Dry un & Overload Protection elay with ure F3 D1 Dry un & Overload Protection elay with ure ure, Unbalance, Phase sequence and overloading Auto / eset, selectable characteristics, 1O/2O output relay ure, Unbalance, Phase sequence, Overloading & Dry running Auto/ eset, selectable overload characteristics, 1O/2O output relay ure, Unbalance, Phase sequence, overloading and dry running Auto/ eset, Adjustable overload characteristics, 1O output relay System Output elay ontact Input 100-120 / 220-240 / 380-440 V A ±20% 110/240/380/4 V A/D/ 24 V A/D ±20%, 50 / 60 Hz 1 O (2 O) 100-120/220-240/380-440V A ±20% 110/240/380/4/440 V A/D/24 V A/D±20%, 50/60 Hz 1 O (2 0) From TS From TS From TS 220-240/380-440 V A ±20% 50/60 Hz ±3% 110 / 240 / 380/ 4 V A ±20% 50 / 60 Hz 1 O Phase to phase unbalance Under current (Dry running) Overload UV/OV Trip Time delay On phase failure esetting For overloading Dimensions (mm) Overall (L x W x D) Panel mounting (L x W) Approx Weight 50% of motor urrent ±10% Above 120% of set urrent (IDMTL) 50% of motor urrent 50%/75% of set current Above 120% of set current (IDMTL) 5.5 secs. ± 1.5 secs. As per selectable inverse time haracteristics (2 secs. / 5 secs.) or 10 secs. or secs. or 20 secs. (optional) 5.5 secs. ± 1.5 secs. As per selectable inverse time haracteristics 2 / 5 secs (10 secs.) UV/OV P 50% of I FL 50% or 75% of I SET Above 120% of set current (IDMTL) 5.5 secs. ± 1.5 secs. As per selectable inverse time haracteristics 2-10 secs. (variable) Auto / / emote Auto / / emote Auto / / emote 67 x 46 / 35 mm ail Mounting 425 gms. 67 x 46 / 35 mm ail Mounting 425 gms. 96 x 96 x 76 92 x 92 425 gms. Wherever not specified ontact ating : 5A @ 230 V A (resistive) urrent 70 60 40 20 12 10 1 As per IDMTL 4 to 7 sec. urrent 70 60 40 20 12 10 1 As per IDMTL 4 to 7 sec. urrent 70 60 40 20 12 10 1 As per IDMTL 4 to 7 sec. O = SP Trip Delay = SP / D Trip Delay = SP / D Trip Delay 5Amp. Sec. T 5 Amp. Sec. T V MOTO /V Dol Starter /V Dol Starter Aux Supply 1 2 3 4 5 6 MP-D2 7 8 9 10 11 12 17 18 Link at 17, 18 for 2 or 5 secs. IDMTL curve A TS- 5 I I O O SUPPL 1 2 3 4 5 6 SPG D2 7 8 9 10 11 12 17 18 1 I 2 3 TS 5/10 O I O Submersible Pump A E F G H F3 D1 O EXT. P.. D A/M D D U SUPPL Submersible Pump 24 elay contact position shown in 'Power on' (Healthy) condition
M O T O / P U M P P O T E T I O E L A S D2 MP1 Dry un & Overload Protection elay with ure D2 MP2 Dry un & Overload Protection with ure & UV+OV Dry un & Overload Protection elay with ure TS1 urrent Sensor ure, Unbalance, Phase sequence and overloading, Auto/ eset, Test Facility, U bypass facility, selectable overload characteristics, 2O output relay Sensing both voltage and current signals, ure, Unbalance, Phase sequence, under over voltage, overloading and dry running. eset, Delayed auto reset, fixed trip settings, fixed overload characteristics, 2O output relay ure, Unbalance, Phase sequence, overloading and dry running (Under current) Microcontroller based design, SMD technology, Auto/ eset, Adjustable current trip settings, selectable overload characteristics, 2O output relay urrent sensor suitable for full load motor current of 5A. 10A. 20A. 40A. & 80A. To be used with Minilec relays only. 380-440 V A ± 20%, 45-65 Hz 220-240 / 380-440V A 2 O 380-440V A ± 20%, 48-63 Hz 220-240 ± 20% VA 2 O 100-120/220-240/380-440V A ± 20%, 48-63 Hz 100-120/220-240VA±20%, 24V D+10%-% 2 O 3-wire Output 50% of urrent (Fixed) 50% to 80% of set current (Adj.with ypass facility) 50% of urrent (Fixed) 50% of set current (Fixed) UV = -20% (Fixed) OV = +20% (Fixed) 50% of urrent (Fixed) 40% to 80% of set current 4 Sec ± 1 Sec As per Inverse Time haracteristics 2/5/10 Sec. (Selectable) Auto/ (emote with Push utton) 4 Sec ± 1% 4 Sec ± 1 Sec (Fixed) As per Inverse Time haracteristics 2 Sec. (Fixed) For UV/OV - 4 Sec ± 1 Sec for P - Instant Delayed Auto As per Inverse Time haracteristics 2/5/10 Sec. (Selectable) Auto / 67 x 46 /35 mm ail Mounting 67 x 46 /35 mm ail Mounting 35 mm ail Mounting 35 mm ail Mounting 0 gms 0 gms. urrent 70 60 40 20 12 10 1 As per IDMTL 70 urrent 60 40 20 12 10 1 As per IDMTL 70 urrent 60 40 20 12 10 1 As per IDMTL 17 17 7 8 10 11 18 18 7 9 10 12 = SP / D Trip Delay = SP / D Trip Delay = SP / D Trip Delay SUPPL UIT EMOTE ESET P.. A D TS SUPPL UIT EMOTE ESET P.. A D TS elay position shown in 'Power off' condition 25
T IPUT MIOPOESSO ASED MOTO POTETI ELA F3 MP1 Protection elay MMP omprehensive Protection elay T Module ( T 20 / T 50 ) ew Microcontroller based. Sensing voltage, current and temperature Protecting against ure, Unbalance, Phase sequence, Under/over voltage, overloading, winding over temperature, Over current/short circuit, locked rotor, Auto/ resetting, Adjustable trip settings for UV/OV, U/O,, Locked rotor & earth fault, On delay & start-up delay adjustable, 2x1O output relays and serial communication port T Module is specially designed for use with Minilec relays only like F3 MP1. MMP and M-ommander Available in 2 module, 0 and T50. Interconnecting cable (2.5mtrs) is provided with this module. F3 MP 1 System Output elay ontact Serial ommunication 220-440 V A ±20%, 45-65Hz 90-270 V A/D 2 O Provision of S485 Output Protection Setting Trip Delay LD Display esetting Parameter ange Mode Over load As per IDMTL har 2/5/10//20 Sec.A Over Load Unbalance 20% 60% 1-10 Sec urrent Unbalanced Multi Attempt Phase Faliure.A 1-10 Sec urrent S.P. Multi Attempt everse Phasing.A Instant Phase eversal Under urrent 30%-90% 1-60 Sec Under urrent Over urrent 300%-800% 2-25 Sec Over urrent }Multi Attempt Lock otor 200%-500% 1-10 Sec otor Lock Earth Fault Setting 30%-80% 0.5-10 Sec Earth Fault Over Temp. o 70 to 180 1-20 Sec Sensor Fail, Auto/ o Temp. High Display Dimensions (mxm) Overall (L x W x D) Mounting (L x W) Approx Weight Unit x2 LD Display 96 x 96 x 80 Panel Mounting - 92 x 92 MMP System Output Input Power onsumption 4V A ±20%, 3Ø, 3 Wire, 50 / (60)Hz ± 3% 90-270V A / D 1 O for Trip & 1 O for Alarm / S 232 Port External TS ( T5/0/T50 ) 8 VA Settings Trip Level Trip Delay LED eset Mode Power Unbal/Ph.ev 1% - 20% Auto / Under Voltage 75% - 95% Auto / Over Voltage 105% - 120% Auto / urrent unbalance 20-60% of Imax Multi Attempt urrent phase Loss Multi Attempt Under urrent} (dry run) 30-90% of Imax D-M Multi Attempt Over urrent/ Short ircuit 300% - 800% of Imax 2-25 Secs. Multi Attempt Overload Lock otor Earth Fault 2/5/10//20 Sec. 200%-500% of Imax 30% - 80% As per IDMTL char. 0.5-10 Secs. Winding Overheat 4K1-5K6 1-20 Secs. Auto / x2 h. ( ack lit ) Display Dimensions (mm) Overall (L x W x D) Panel mounting (L x W) Approx Weight 6 x 2 x 80 3 x 203 600 gms 3 wire output with interconnection cable Input from... phases and T T Module Selection hart T ange 0 For motor currents (FLA) upto 20 Amp T50 For motor currents (FLA) upto 50 Amp 102 x 35 x 81 90mm ail Mounting centre to centre 600 gms EXTEAL T OF 5Amp OUTPUT T MODULE ( TS / 0 / T50 ) S1 EXTEAL T OF 5Amp OUTPUT 1 2 3 4 5 6 7 SUPPL 485 O/P PT I/P S1 T MODULE ALAM TIP E L 4 2 O2 2 1O1 1 2 3 SUPPL SSTEM SUPPL ELA OUTPUT S-232 OUTPUT T IPUT G 6 1 T4 T3 PT-1 FO ALAM PT-2 FO TIP 1 01 1 2 02 2 8 9 10 11 12 MMP F3 MP1 26 elay contact position shown in 'Power off' condition P Side Software
MIOPOESSO ASED PUMP AUTOMATI SSTEM T Module ( T 5 ) M-OMMADE Pump Management & Protection System For currents above 50Amp ustomers to use suitable external T of 5Amp Secondary and T Module T 5 M-ommander is a micro-processor based protection and Pump management system, suitable for 2 pumps. Sensing voltage, current and temperature Protecting against ure, Unbalance, Phase sequence, Under/over voltage, overloading, dry running, winding over temperature, Over current/short circuit, locked rotor, earth fault, Auto/ resetting, Adjustable trip settings for UV/OV, U/O,, Locked rotor & earth fault, On delay & start-up delay adjustable, 2x1O output relays T based time settings Water level control To Unit EXTEAL T OF 5 Amp SEDA 1 2 5 6 T-5 35 mm ail Mounting EXTEAL T OF 5 Amp OUTPUT PUMP protection Includes Under/ Over voltage protection Single/everse phasing protection Voltage / urrent unbalance Overload trip Over current protection Dry running protection Earth fault protection PT based winding overheating protection Pump Management System Features Auto hange over between two pumps Intelligent resetting facility On-site programming facility Password protection for programming Pump On-Off timer programmable for 10 times a day, with advance programming of 7 days Provision for water level control un-time compensation Ideal for Pump Automation & Unmanned Pumping Stations. PAAMETES SPEIFIATIS System 4 V A ±20%, 50/60Hz ±3% 90-270 VA/D ±20%, 50Hz Output ontacts 4 x 1 O elays (for 1 pump) urrent sensor External T5 / 0 / T50 eset Auto/ Multi-Attempt / Unbalance 1-20% ± 6V for Voltage Unbalance 20-60% ± 5% of current unbalance Overload Over urrent / 300% - 800% Short ircuit Locked otor 200% - 500% Earth Fault 30% - 80% Winding Overheating As per PT temperature characteristics Under Voltage 75% - 95% of system supply (adjustable) Over Voltage 105%-120% of system supply (adjustable) Dry unning 30-90% of Imax Display x2 h. ( acklit ) Level ontrol Weight Upper tank full Lower tank empty 800gms Wherever not specified ontact ating : 5A @ 230 V A (resistive) For more detailed specifications, refer table on page o. 26 (MMP) EXTEAL T OF 5Amp OUTPUT T MODULE (0 / T50) S1 PUMP-1 PUMP-2 E L 4 2 SUPPL SSTEM SUPPL T IPUT 6 1 P2 P3 3 P1 PUMP-2 PIMIG PUMP-2 PUMP-1 PIMIG PUMP-1 4O4 4 3O3 3 2O2 2 1O1 1 ELA OUTPUT IPUT IP1 P4 P5 P6 T4 T3 WIDIG TEMP SESO ( PT - 1) FO PUMP- 1 WIDIG TEMP SESO ( PT - 2) FO PUMP- 2 P6 P5 P4 UPPE TAK P3 P2 P1 LOWE TAK M-OMMADE For Auto operation, Put link across '' push button elay contact position shown in 'Power off' condition 27
WIDIG OVE-TEMPEATUE POTETI ELAS WT D1 Winding Protection elay W PT Thermistor elay PT Thermistor Sensing motor winding temperature through PT Thermistors, Winding overheating, sensor short, sensor open faults Suitable for single, triple or 6/9/12 PTs Sensing motor winding temperature through PT Thermistors, Winding overheating, sensor short, sensor open faults Suitable for single, triple or 6/9/12 PTs Output ontacts Thermistor Sensor Healthy Thermistor Sensor Trip Thermistor Sensor Open Thermistor Sensor Short Trip time delay Wherever not specified ontact ating : 5A @ 230 V A (resistive) 110-120/220-240/380-440 A / V A / 24 V D ±10% 1 O 40 ohm - 4 K ohm 4.1 K ohm - 5.5 K ohm 5.6 K ohm & above 40 ohm & below Less than 2 secs. 12/24V D/100-120/220-240/380-440V A, 50Hz(60 Hz)±10% 2 O 40 Ù to 4K Ù 4.1K Ù 5.5K Ù 5.6K Ù & Above 0-39 Ù Less than 1 Sec (Fixed) esetting elow 1.51 K elow 1.51 K Dimensions (mm) Overall (L x W x D) 76 x 30.5 x 117.5 Mounting (L x W) 68 mm centre to centre / 35 mm ail Mounting 35 mm ail Mounting Weight 300 gms. 250 gms. esetting Mode Auto / (Optional) Auto / TPIAL HAATEISTIS OF PT (THEMISTO) ESISTAE I OHMS 6000 5600 5000 4000 ESISTAE VS TEMPEATUE PT THEMISTO DITI AD TIP SETTIGS OPEED (ESISTAE > 5.6k) UHEALTH (ESISTAE >4.2k < 5.5k) O/P ELA STAT PT Thermistors are semi conductor sensors. These have typical characteristics that change their resistance instantly at a specified pre-defined response temperature (T). As soon as the surrounding temperature of PT reaches it's T value the body resistance of PT Thermistor rises sharply from 200 / 250 Ohms to more than 5000 Ohms.The PT Thermistors are embedded in the overhang location of the motor windings. The T value of PT is selected according to the Insulation lass of the copper windings of motor or transformers. Selection hart for T of PT Thermistors. T lass able olour 0 of Ins. ode 70 White - rown 80 White - White 90 Green - Green 3000 2000 elay eset Zone (>1.5K<1.8K) 100 A ed - ed 00 1000 500 250 200 HEALTH ESISTAE >39W<4K 110 rown - rown 120 E Grey - Grey 100 250 OOM TEMP. T-20 SHOTED T-5 T T+5 T+ (ESISTAE < 3.9W 0 lue - lue 0 White - lue MOTO M 0 F lack - lack 0 lue - ed /V 170 H White - Green DOL STATE Aux. Supply 1 3 5 6 180 White - ed 190 Orange - lack W 1 2 3 WTD1 Aux. Supply 7 8 9 eset eset 28 elay position shown in Power on condition elay position shown in 'Power off condition