Honeywell Process Solutions Field Device Manager Express Software Installation User's Guide EP-FDM-02430X R430 June 2012 Release 430 Honeywell
Notices and Trademarks Copyright 2010 by Honeywell International Sárl. Release 430 February, 2012 While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customers. In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change without notice. Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc. Other brand or product names are trademarks of their respective owners. Honeywell Process Solutions 1860 W. Rose Garden Lane Phoenix, AZ 85027 USA 1-800 822-7673 ii Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
About This Document This guide describes how to install Field Device Manager (FDM) Express. For the sake of brevity, this guide does not repeat the applicable general guidelines, considerations, cautions, and so on that are covered in the other Experion system guides. Release Information Document Name Document ID Release Number Publication Date Field Device Manager Express Software Installation User's Guide EP-FDM- 02430X 430 April 2012 References The following list identifies all documents that may be sources of reference for the material discussed in this publication. Document Title Doc ID Experion Software Installation and Upgrade Guide FDM R430 User s Guide EP-FDM-11430 R430 Field Device Manager Express Express Software Installation User's Guide iii June 2012 Honeywell
Support and Other Contacts Support and Other Contacts United States and Canada Contact: Honeywell Global Technical Support Center Phone: 1-800-423-9883 Email hfs-tac-support@honeywell.com Europe, Middle East and Africa (EMEA) Contact: Honeywell Technical Assistance Center Phone: +44 1202645583 Email hfs-tac-support@honeywell.com Other Regions Contact: Email Honeywell Global Technical Support Center hfs-tac-support@honeywell.com Training Classes Honeywell Automation College: http://www.automationcollege.com iv Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
Symbol Definitions Symbol Definitions The following table lists those symbols used in this document to denote certain conditions: Symbol Definition : Identifies information that requires special consideration. TIP: Identifies advice or hints for the user, often in terms of performing a task. REFERENCE -EXTERNAL: Identifies an additional source of information outside of the bookset. REFERENCE - INTERNAL: Identifies an additional source of information within the bookset. CAUTION Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being damaged or lost, or may result in the inability to properly operate the process. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. CAUTION symbol on the equipment refers the user to the product manual for additional information. The symbol appears next to required information in the manual. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in serious injury or death. WARNING symbol on the equipment refers the user to the product manual for additional information. The symbol appears next to required information in the manual. WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible. R430 Field Device Manager Express Express Software Installation User's Guide v June 2012 Honeywell
Symbol Definitions Symbol Definition ESD HAZARD: Danger of an electro-static discharge to which equipment may be sensitive. Observe precautions for handling electrostatic sensitive devices. Protective Earth (PE) terminal: Provided for connection of the protective earth (green or green/yellow) supply system conductor. Functional earth terminal: Used for non-safety purposes such as noise immunity improvement. NOTE: This connection shall be bonded to Protective Earth at the source of supply in accordance with national local electrical code requirements. Earth Ground: Functional earth connection. NOTE: This connection shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements. Chassis Ground: Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements. vi Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
Contents 1. BEFORE YOU BEGIN...9 1.1 Planning and design guidelines... 9 1.2 Installation components and requirements... 9 Package information...9 FDM Express installation components...9 License information... 10 Hardware and software requirements... 11 FDM Express compatibility with Experion releases... 11 1.3 Installation Scenario... 12 Overview... 12 Typical Architecture of FDM Express... 12 2. FDM EXPRESS INSTALLATION... 13 2.1 Installing FDM Express... 13 Prerequisites... 13 To install FDM Server... 14 2.2 Installing FDM Client... 20 Prerequisites... 20 To install FDM Client... 20 3. POST INSTALLATION TASKS... 25 3.1 Updating the FDM license... 25 Prerequisites... 25 3.2 Executables required in DEP exception list... 27 Adding executables to Data Execution Prevention (DEP) execution list... 27 3.3 Configuring the network information... 28 3.4 First logon... 28 4. FDM MAINTENANCE... 31 4.1 Overview... 31 Before starting FDM maintenance... 31 4.2 Modifying FDM components... 32 R430 Field Device Manager Express Express Software Installation User's Guide vii June 2012 Honeywell
Contents 4.3 Repairing FDM components... 36 4.4 Removing FDM... 40 viii Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
1. Before You Begin 1.1 Planning and design guidelines FDM Express is an on-the-go version of Field Device Manager designed for use in the maintenance shop and suitable for installation in a Win 7 laptop or desktop PC. It is important that you plan the installation of FDM Express, so please refer to EP03-480-, Field Device Manager Express Specifications, for information on PC hardware, PC operating system, and peripheral requirements. Also, refer to the specifications for details about performance and operational limits and to decide upon the number of tag licenses you need. Up to 1000 tags are supported by FDM Express. FDM server installation includes installation of Microsoft SQL Server 2008 Standard Edition and Microsoft SQL Server 2008 Service Pack1. As a result, FDM server installation takes considerable time. 1.2 Installation components and requirements Package information Component Software Media Software Media FDM R430 setup software Field Device Manager Software R430.1 DVD 1 Type DVD Microsoft SQL Server 2008 R2 SP1 FDM Express License Field Device Manager Software R430.1 DVD 2 Field Device Manager License CD R430.1 DVD CD FDM Express installation components FDM Express installation supports the following components. FDM Server: FDM Server forms the core of FDM application. It manages the FDM client and interacts with HART and PROFIBUS devices through the Remote Communication Interface (RCI). It stores all persistent information related to the R430 Field Device Manager Express Express Software Installation User's Guide 9 June 2012 Honeywell
1. Before You Begin 1.2. Installation components and requirements devices, networks, and FDM users. For FDM Express Server installation, FDM Client and RCI are required and they are automatically selected and installed during the installation. FDM Client: FDM client is the user interface component of the FDM application. The client enables you to connect-to FDM Server and performs various functionalities supported by FDM. FDM RCI: Remote Communication Interface (RCI) is the component in FDM that manages the interaction with devices connected to the communication interfaces. It is also included in the FDM Express installation. The following table lists the communication interfaces and the respective device which can be connected. Communication Interfaces Devices HART Profibus RS-232 HART Modem Supported Not applicable RS-485 HART Multiplexer Supported Not applicable Communication/Gateway DTMs Supported Supported The FDM RCI is installed in FDM Express Server. License information Mux Monitoring Solution: This component, available with the full FDM product, is not available with FDM Express. FDM HART Multiplexer: This component, also available with the full FDM product, is not available with FDM Express Station Maintenance View: This option is only used with Experion for the full FDM product. It is not available with FDM Express. An FDM Express license upgrade is a requirement for the software to function. The Server Management Tool provides the functionality to manage the license for FDM. Using the Licensing option, you can upgrade (install) the provided FDM Express license. After installing of FDM, ensure to upgrade FDM with the provided license. 10 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
1. Before You Begin 1.2. Installation components and requirements REFERENCE - INTERNAL For more information on upgrading license, refer to the Upgrading FDM license in the FDM User s Guide. Hardware and software requirements REFERENCE - INTERNAL Refer to EP03-480-430X, Field Device Manager Express Specifications, for information on hardware and software requirements. FDM Express compatibility with Experion releases FDM Express does not support connection with Experion R400. Only the full FDM product supports this. REFERENCE - INTERNAL For more information, refer to the Release Notes document for FDM release. R430 Field Device Manager Express Express Software Installation User's Guide 11 June 2012 Honeywell
1. Before You Begin 1.3. Installation Scenario 1.3 Installation Scenario Overview In FDM Express, the installed server handles the database required to the store device information. The FDM Express server, along with FDM Remote Communication Interface component, enables the FDM Express Client to access the required data from devices connected via a MUX, modem or Comm DTM network. FDM Express is installed in a Win 7 or Windows 2008 laptop or desktop computer for use with locally available HART or PROFIBUS instruments. Typical Architecture of FDM Express The following diagram depicts the network architecture of FDM Express as used in the maintenance shop. FDM Express in Laptop PC USB to RS 485 Converter OR USB HART Modem MUX Network & Devices HART Device Network architecture of FDM The following components are installed during the FDM installation. FDM Server, along with FDM Client and FDM RCI. When you select FDM Server for installation, the FDM Client and FDM RCI are also selected by default. 12 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation Manuals provided with FDM Express reflect the complete, full FDM product offering. Many documented options are not offered with FDM Express. The user should be aware of this. This section covers the following topics which provide an overview of installation. Topic Page Installing FDM Express (laptop or desktop) 15 Installing FDM Client 22 Ensure that your Antivirus solution is not configured to block copying of files or prevent installations from registering services. To install FDM Express R430 successfully, the user must have administrative privileges. 2.1 Installing FDM Express Prerequisites The user should have FDM Express R430 DVD media ready. The user must be a member of an Administrator group to install FDM Server. Ensure you close all Windows applications before starting FDM Server software Installation. Ensure Windows Firewall / Internet Connection Sharing (ICS) service is running. R430 Field Device Manager Express Express Software Installation User's Guide 13 June 2012 Honeywell
2. FDM Express Installation 2.1. Installing FDM Express To install FDM Server Perform the following steps. 1 Insert FDM Express software DVD into the DVD drive. 2 Right-click setup.exe and then click Run as administrator. The Field Device Manager - InstallShield Wizard appears. 3 Click Next. You must close all the other applications before proceeding with the installation. The License Information page appears. 4 Read the license agreement, and then:, Click Yes, if you accept the terms. Or Click No, if you do not accept the terms. When you click Yes, the Common Information page appears. 5 Read the common information, and then click Next. The Product Registration page appears. 6 Type the name of the User. 7 Type the name of the Organization. 8 Click Next. 14 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation 2.1. Installing FDM Express The Module selection page appears. R430 Field Device Manager Express Express Software Installation User's Guide 15 June 2012 Honeywell
2. FDM Express Installation 2.1. Installing FDM Express 9 Select FDM Server component, and then click Next. When you select FDM Server option, FDM Client and Remote Communication Interface (RCI) are also selected. If you are installing FDM Server on an unqualified operating system, the following message appears. Click OK to proceed with the installation on an unqualified operating system. The Enter User Account Information page appears. FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user does not exist, you need to enter new password to create the user. 10 Type the Password. 16 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation 2.1. Installing FDM Express You should type the same password on any FDM computers, when prompted during installation. The Password should contain a combination of alphabetic, numeric and special character(s). It should have a minimum of eight characters in domain. It cannot have any blank spaces. The password should also conform with system password policy. 11 Retype the password in Confirm Password. 12 Click Next. The User Group Information page appears. The FDMMngr user account is created along with the following 4 default user groups. FDM Administrators FDM Engineers FDM Operators and FDM Supervisors Note that the password for this group is not the same as the FDM login password. In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users to enable communication across computers. An error message appears, if the FDMMngr account already exists on this computer and the password typed does not match with the existing FDMMngr password. In such a scenario, perform the following: 1. Choose Start > All Programs > Administrative Tools > Computer Management. 2. Expand Local Users and Groups > Users. 3. Right-click the User name and then click one of the following as necessary. a) Set Password: If you want to change the password. b) Delete: If you want to delete the user. R430 Field Device Manager Express Express Software Installation User's Guide 17 June 2012 Honeywell
2. FDM Express Installation 2.1. Installing FDM Express 13 Click Next. If the SQL Server 2008 is already installed, the Enter database information page appears. 1. Select Windows Authentication. 2. Click Validate and then click Next. A Destination Folder page appears, displaying information about the default destination folder. If you want to change the default destination folder, click Browse to specify a different destination folder. 14 Click Next. A page appears, prompting you to verify the selected options and displaying the components selected for installation and the destination path. Also, it displays the prerequisites which are to be installed as part of installation. 15 Click Install. The setup starts installing all the prerequisites if they are not already installed. Both after installing Microsoft.Net framework 3.5 Service Pack1 and Microsoft SQL Server 2008, you are prompted to restart the computer. Click OK to continue. After the computer restarts, log on again as a user with Administrator privileges. The Setup Status page appears displaying installation status. After the installation is complete, the Setup complete page appears. 16 Select Yes, I want to restart my computer now, if you want to restart the computer. Or Select No, I will restart my computer later. It is recommended to always restart the computer immediately after the installation is complete. After you restart the computer, you must first update the FDM License using CD. For more information, refer to section Updating the FDM license. 18 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation 2.1. Installing FDM Express 17 Click Finish. R430 Field Device Manager Express Express Software Installation User's Guide 19 June 2012 Honeywell
2. FDM Express Installation 2.2. Installing FDM Client 2.2 Installing FDM Client FDM Server installation automatically installs the FDM Client on that computer. Normally, this is all that would be required. You can also install FDM Client in separate PCs that are networked to the FDM Express Server and log into the FDM Express Server via any other Client. Separate Clients must be in PCs that are in the same Workgroup or same Domain as the Server. With FDM Express, only one Client may be used at a time. Prerequisites To install FDM Client Do not install the RCI component with Client, since FDM Express does not support the remote RCI node. Note there is no problem if the RCI is installed, but it cannot be used. By default FDM Server, FDM Client, and Remote Communication Interface (RCI) are selected, you can clear FDM Server and Remote Communication Interface (RCI) option to install FDM Client. FDM R430 DVD media. Perform the following steps. 1 Insert FDM software DVD into the DVD drive. 2 Right-click setup.exe and then click Run as administrator. The Field Device Manager - InstallShield Wizard appears. 3 Click Next. You must close all the other applications before proceeding with the installation. The License Information page appears. 4 Read the license agreement, and then:, Click Yes, if you accept the terms. Or Click No, if you do not accept the terms. 20 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation 2.2. Installing FDM Client When you click Yes, the Common Information page appears. 5 Read the common information, and then click Next. The Product Registration page appears. 6 Type the name of the User. 7 Type the name of the Organization. 8 Click Next. The Module selection page appears. 9 Select the feature(s) that you want to install and click Next. The Enter User Account Information page appears. FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user doest not exist, you need to enter new password to create the user. 10 Type the Password. You should type the same password on any FDM computers, when prompted during installation. The Password must contain a combination of alphabetic, numeric and special character(s). It must have a minimum of eight characters in domain. It must not have any blank spaces. The password should also confirm with system password policy. 11 Retype the password in Confirm Password. R430 Field Device Manager Express Express Software Installation User's Guide 21 June 2012 Honeywell
2. FDM Express Installation 2.2. Installing FDM Client 12 Click Next. The FDMMngr user account is created and a default user group is created as: FDMAccessGroup: It is used for providing permissions to Windows users to enable communication across computers. An error message appears, if the FDMMngr account already exists on this computer and the password typed does not match with the existing FDMMngr password. In such a scenario, perform the following: 3. Choose Start > All Programs > Administrative Tools > Computer Management. 4. Expand Local Users and Groups > Users. 5. Right-click the User name and then click one of the following as necessary. a) Set Password: If you want to change the password. b) Delete: If you want to delete the user. A Destination folder page appears, displaying information about the default destination folder. If you want to change the default destination folder, click Browse to specify the different destination folder. 13 Click Next. A page appears, prompting you to verify the selected options and displaying the components selected for installation and the destination path. Also it displays the prerequisites which are to be installed as part of installation. 14 Click Install. The setup starts installing all the prerequisites if they are not already installed. 22 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
2. FDM Express Installation 2.2. Installing FDM Client The Setup Status page appears displaying the installation status. After the installation is complete, the Setup complete page appears. 15 Select Yes, I want to restart my computer now, if you want to restart the computer. Or Select No, I will restart my computer later. 16 Click Finish. It is recommended to always restart the computer immediately after the installation is complete. R430 Field Device Manager Express Express Software Installation User's Guide 23 June 2012 Honeywell
3. Post Installation Tasks This section describes the tasks that must be performed after FDM installation depending on the configuration and set up. 3.1 Updating the FDM license Prerequisites FDM features are not enabled until you update (install) the required license. FDM R430 license file. To update FDM License, perform the following steps. 1 Insert media which contain the license file for FDM. 2 Copy the license file from the media to the local system. 3 Log on to FDM Server Management Tool. For more information, refer to section Logging on to the FDM Server Management Tool in FDM User s Guide. Ensure that the FDM Server is stopped. R430 Field Device Manager Express Express Software Installation User's Guide 25 June 2012 Honeywell
3. Post Installation Tasks 3.1. Updating the FDM license 4 Click the Licensing icon in the left pane of the window. The list of features and the licensing details appears in the right pane. The licensing information is listed with the following details: Option indicates the name of the feature pertaining to the software. Status refers to the present status of the license for a feature. It is Licensed or Not Licensed. Value(s) specifies the number of licenses provided for each feature. For some of the features, the values are license enabled or disabled. 5 Click Browse to select the license file. The Select a License File dialog box appears. 6 Select the file and click Open. The path for the license file (with the.xml extension) appears under Update License. 7 Click Update. A confirmation message appears displaying license has been updated and click OK. 8 Click Exit to close FDM Server Management dialog box. 26 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
3. Post Installation Tasks 3.2. Executables required in DEP exception list 3.2 Executables required in DEP exception list The following executables must be added to the Data Execution Prevention exception list, depending upon the FDM components you have selected during the installation. In case you fail to do so, it may result in FDM components stopping to respond while using DTMs. On FDM Client and FDM Server node: HCMClient.exe Default installation path: C:\Program Files\Honeywell\FDM\ClientMachine\Bin\HCMClient.exe Adding executables to Data Execution Prevention (DEP) execution list To add the executables to Data Execution Prevention execution list, perform the following steps. 1 Choose Start > Control Panel. The Control Panel appears. Click Classic view and double-click System. Under Task, click Advanced system settings. Or Right-click Computer and click Properties. The System Properties dialog box appears. 2 Click the Advanced tab. 3 Under Performance, click Settings. The Performance Options dialog box appears. 4 Click the Data Execution Prevention tab. 5 In case Turn on DEP for essential Windows programs and services only option is selected, then go to step 6. Or, In case, Turn on DEP for all programs and services except those I select option is selected, then click the Add button and select the executables depending on the components you have selected. 6 Click Apply. 7 Click OK to close the Performance Options dialog box. 8 Click OK to close the System Properties dialog box. R430 Field Device Manager Express Express Software Installation User's Guide 27 June 2012 Honeywell
3. Post Installation Tasks 3.3. Configuring the network information 9 Restart the computer. 3.3 Configuring the network information After FDM installation and upgrading license is complete, you must configure networks using Server Management Tool on FDM Server. REFERENCE INTERNAL For more information about Configuring Networks, see FDM User s Guide. The only valid network types supported by FDM Express are: RS-232 HART modem: FDM uses the RS-232 HART Modem to communicate with HART devices using the serial port. A USB-to-RS-232 adaptor is required for a laptop. Honeywell HART DE modem: The Honeywell HART DE Modem provides the network communication interface to HART devices. Again, ausb-to-rs-232 adaptor is required. RS-485 HART multiplexer: Using a USB-to-RS485 adaptor, FDM can communicate to multiple HART devices in the field connected to HART Multiplexers. A single HART Multiplexer network can support up to 31 multiplexers. Comm DTM Interface: FDM supports communications to Profibus and HARTover-Profibus devices using FDT/DTM technology. See the FDM User s Guide for more information about these different network types. 3.4 First logon You must provide valid user credentials to log on to FDM Client or FDM Server Management Tool. FDM has a predefined user name Administrator. When you launch FDM client, you can specify the server name to which the client must connect to. For the first login, you must enter the server name. If FDM client connects to the specified FDM server, then the server name is saved and it is available for selection in the dropdown list during subsequent logins. After the connection to the server, enter the following login details: Login Name: administrator 28 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
3. Post Installation Tasks 3.4. First logon Password: password Domain Name: Classic Server Security It is recommended to log on to FDM Client and change this password after the initial system configuration is complete. REFERENCE INTERNAL For more information about user log on, see FDM User s Guide. R430 Field Device Manager Express Express Software Installation User's Guide 29 June 2012 Honeywell
4.1 Overview 4. FDM Maintenance The FDM installation supports the following using FDM Maintenance option. Modify Using this option you can add new component(s) or remove the currently installed component(s). Repair Using this option you can reinstall the selected components installed by the previous setup. Remove Using this option you can remove all the selected components. Before starting FDM maintenance Perform the following before proceeding with the FDM maintenance: Log on to Server Management tool, and stop FDM Server. On the FDM Server PC, choose Start > Control Panel > Administrative Tools > Services and stop the FDM Remote Communication Interface service. Ensure all SQL applications (like query analyzer and SQL Enterprise manager and so on.) are closed. Ensure all FDM application windows are closed. R430 Field Device Manager Express Express Software Installation User's Guide 31 June 2012 Honeywell
4. FDM Maintenance 4.2. Modifying FDM components 4.2 Modifying FDM components Using this option, you can remove any currently installed component or install a new component along with the currently installed component. To modify FDM installation, perform the following steps. 1 Choose Start > All Programs > Honeywell FDM > FDM Maintenance. Or, Choose Start > Control Panel > Programs and Features. Select Field Device Manager and click Change. Or, Insert FDM software DVD into the DVD drive. 2 Right-click setup.exe and click Run as administrator. The FDM Maintenance page appears. 32 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
4. FDM Maintenance 4.2. Modifying FDM components You must close all other applications before you proceed. 3 Click Modify, and then click Next. The Add/Remove Features page appears. 4 Perform any one of the following to modify the installation, as necessary. If you want to remove a feature, clear the check boxes corresponding to the already installed features. Or, If you want to add a feature, select the feature. 5 Click Next. The Enter User Account Information page appears. FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user does not exist, you need to enter new password to create the user. 6 Type the Password. You must type the same password on all the computers, when prompted during installation. The Password must contain a combination of alphabetic, numeric and special character(s). It must have a minimum of eight characters in domain. It must not have any blank spaces. The password should also confirm with system password policy. 7 Retype the password in Confirm Password. 8 Click Next. R430 Field Device Manager Express Express Software Installation User's Guide 33 June 2012 Honeywell
4. FDM Maintenance 4.2. Modifying FDM components If FDM Server is selected during maintenance, the following message appears. Click Yes to proceed with the maintenance. If you select FDM Server, the User Group Information page appears. The FDMMngr user account is created along with the following 4 default user groups. FDM Administrators FDM Engineers FDM Operators and FDM Supervisors In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users to enable communication across computers. If you select other features (FDM Client, FDM RCI, FDM HART Multiplexer, Station Maintenance View, or Mux Monitoring Solution), the FDMMngr user account is created and a default user group is created as: FDMAccessGroup: Its is used for providing permissions to Windows users to enable communication across computers. 34 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
4. FDM Maintenance 4.2. Modifying FDM components 9 Click Next. An error message appears, if the FDMMngr account already exists on this computer and the password typed does not match with the existing FDMMngr password. In such a scenario, perform the following: 1. Choose Start > All Programs > Administrative Tools > Computer Management. 2. Expand Local Users and Groups > Users. 3. Right-click the User name and then click one of the following as necessary. a) Set Password: If you want to change the password. b) Delete: If you want to delete the user. A page appears, prompting you to verify the selected options and displaying the components selected for installation and the destination path. Also it displays the prerequisites which are to be installed as part of installation. 10 Click Modify. The setup starts installing all the prerequisites if they are not already installed. The Setup Status page appears displaying the maintenance status. After modifying FDM components, the Maintenance Complete page appears. 11 Select Yes, I want to restart my computer now, if you want to restart the computer. Or Select No, I will restart my computer later. 12 Click Finish. It is recommended to always restart the computer immediately after the maintenance is complete. R430 Field Device Manager Express Express Software Installation User's Guide 35 June 2012 Honeywell
4. FDM Maintenance 4.3. Repairing FDM components 4.3 Repairing FDM components Using the Repair option you can reinstall all the components installed by the previous setup. To repair FDM Components, perform the following steps. 1 Insert FDM software DVD into the DVD drive. Repair option is currently not supported through Add/remove programs or FDM Maintenance. The following error message appears, if you try to repair through Add/remove programs or FDM Maintenance. 2 Right-click setup.exe and click Run as administrator. The FDM Maintenance page appears. You must close all the other applications before proceeding with the maintenance. 36 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
4. FDM Maintenance 4.3. Repairing FDM components 3 Click Repair, and then click Next. The Enter User Account Information page appears. FDM creates an internal user known as FDMMngr, which is used for authentication purposes. If the user doest not exist, you need to enter new password to create the user. 4 Type the Password. You must type the same password on all the computers, when prompted during installation. The Password must contain a combination of alphabetic, numeric and special character(s). It must have a minimum of eight characters in domain. It must not have any blank spaces. The password should also confirm with system password policy. 5 Retype the password in Confirm Password. R430 Field Device Manager Express Express Software Installation User's Guide 37 June 2012 Honeywell
4. FDM Maintenance 4.3. Repairing FDM components 6 Click Next. If FDM Server is selected during maintenance, the following message appears. Click Yes to proceed with the maintenance. If you are repairing FDM Server, the User Group Information page appears. The FDMMngr user account is created along with the following 4 default user groups. FDM Administrators FDM Engineers FDM Operators and FDM Supervisors In addition to the above groups, the installation creates another group called FDMAccessGroup which is used for providing permissions to Windows users to enable communication across computers. If you are repairing other features (FDM Client, FDM RCI, FDM HART Multiplexer, Station Maintenance View, or Mux Monitoring Solution), the FDMMngr user account is created and a default user group is created as: FDMAccessGroup: It is used for providing permissions to Windows users to enable communication across computers. An error message appears, if the FDMMngr account already exists on this computer and the password typed does not match with the existing FDMMngr password. In such a scenario, perform the following: 1. Choose Start > All Programs > Administrative Tools > Computer Management. 2. Expand Local Users and Groups > Users. 3. Right-click the User name and then click one of the following as 38 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
4. FDM Maintenance 4.3. Repairing FDM components necessary. a) Set Password: If you want to change the password. b) Delete: If you want to delete the user. 7 Click Next. A page appears, prompting you to verify the selected options and displaying the components selected for installation and the destination path. 8 Click Repair. The Setup Status page appears displaying the maintenance status. After repairing FDM components, the Maintenance Complete page appears. 9 Select Yes, I want to restart my computer now, if you want to restart the computer. Or Select No, I will restart my computer later. 10 Click Finish. It is recommended to always restart the computer immediately after the maintenance is complete. R430 Field Device Manager Express Express Software Installation User's Guide 39 June 2012 Honeywell
4. FDM Maintenance 4.4. Removing FDM 4.4 Removing FDM Using Remove option you can remove all the FDM components which are installed in the system. Before you remove FDM, refer to the section Before starting FDM maintenance. If SQL Server 2008 is installed along with FDM, when you remove the FDM Server, the SQL Server 2008 is also removed by default. To Remove FDM components, perform the following steps. 1 Choose Start > All Programs > Honeywell FDM > FDM Maintenance. Or, Choose Start > Control Panel > Programs and Features. Select Field Device Manager and click Uninstall. Or, Insert FDM software DVD into the DVD drive. The FDM Maintenance page appears. You must close all the applications before proceeding with the removal of FDM. 2 Click Remove, and then click Next. 40 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
4. FDM Maintenance 4.4. Removing FDM A page appears displaying the components ready to be removed. 3 Click Remove. The following message appears. 4 Click Yes. The Setup Status page appears displaying the removal status. After the removal of FDM is complete, the Maintenance Complete page appears. 5 Select Yes, I want to restart my computer now, if you want to restart the computer. Or Select No, I will restart my computer later. 6 Click Finish. It is recommended to always restart the computer immediately after completely removing FDM software. R430 Field Device Manager Express Express Software Installation User's Guide 41 June 2012 Honeywell
4. FDM Maintenance 4.4. Removing FDM 42 Field Device Manager Express Express Software Installation User's Guide R430 Honeywell June 2012
Honeywell Process Solutions 1860 W. Rose Garden Lane Phoenix, AZ 85027 USA