VS-6CTQ...SPbF, VS-6CTQ...-PbF Series High Performance Schottky Rectifier, x 8 VS-6CTQ...SPbF ase common cathode Common 3 node cathode node D PK VS-6CTQ...-PbF ase common cathode Common 3 node cathode node TO-6 PRODUCT SUMMRY Package TO-63 (D PK), TO-6 I F(V) x 8 V R 60 V, 80 V, V V F at I F 0.58 V I RM 7 m at 5 C T J max. 75 C Diode variation Common cathode E S 7.5 mj FETURES 75 C T J operation Center tap configuration Low forward voltage drop High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance High frequency operation Guard ring for enhanced ruggedness and long term reliability Meets MSL level, per J-STD-00, LF maximum peak of 60 C EC-Q0 qualified Material categorization: For definitions of compliance please see www.vishay.com/doc?999 DESCRIPTION This center tap Schottky rectifier series has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 75 C junction temperature. Typical applications are in switching power supplies, converters, freewheeling diodes, and reverse battery protection. MJOR RTINGS ND CHRCTERISTICS SYMOL CHRCTERISTICS VLUES UNITS I F(V) Rectangular waveform 6 V RRM 60 to V I FSM t p = 5 μs sine 850 V F 8 pk, T J = 5 C (per leg) 0.58 V T J Range -55 to +75 C VOLTGE RTINGS PRMETER SYMOL VS-6CTQ060SPbF VS-6CTQ060-PbF VS-6CTQ080SPbF VS-6CTQ080-PbF VS-6CTQSPbF VS-6CTQ-PbF UNITS Maximum DC reverse voltage V R 60 80 V Maximum working peak reverse voltage V RWM SOLUTE MXIMUM RTINGS PRMETER SYMOL TEST CONDITIONS VLUES UNITS Maximum average per leg 8 forward current I F(V) 50 % duty cycle at T C = 48 C, rectangular waveform per device 6 See fig. 5 Maximum peak one cycle 5 μs sine or 3 μs rect. pulse Following any rated load 850 non-repetitive surge current per leg I FSM condition and with rated 0 ms sine or 6 ms rect. pulse 75 See fig. 7 V RRM applied Non-repetitive avalanche energy per leg E S T J = 5 C, I S = 0.50, L = 60 mh 7.50 mj Current decaying linearly to zero in μs Repetitive avalanche current per leg I R 0.50 Frequency limited by T J maximum V =.5 x V R typical Revision: 7-Feb-4 Document Number: 9445 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
VS-6CTQ...SPbF, VS-6CTQ...-PbF Series ELECTRICL SPECIFICTIONS PRMETER SYMOL TEST CONDITIONS VLUES UNITS 8 0.7 T J = 5 C Maximum forward voltage drop per leg 6 0.88 V () FM See fig. 8 0.58 T J = 5 C 6 0.69 V Maximum reverse leakage current per leg T J = 5 C 0.55 I () RM V R = Rated V R See fig. T J = 5 C 7.0 m Threshold voltage V F(TO) 0.45 V T J = T J maximum Forward slope resistance r t.07 m Maximum junction capacitance per leg C T V R = 5 V DC (test signal range khz to MHz), 5 C 500 pf Typical series inductance per leg L S Measured lead to lead 5 mm from package body 8.0 nh Maximum voltage rate of change dv/dt Rated V R 0 000 V/μs Note () Pulse width < 300 μs, duty cycle < % THERML - MECHNICL SPECIFICTIONS PRMETER SYMOL TEST CONDITIONS VLUES UNITS Maximum junction and storage temperature range T J, T Stg -55 to +75 C Maximum thermal resistance, 3.5 junction to case per leg R thjc DC operation Maximum thermal resistance,.63 C/W junction to case per package Typical thermal resistance, case to heatsink R thcs Mounting surface, smooth and greased 0.50 pproximate weight Mounting torque Marking device g 0.07 oz. minimum 6 (5) kgf cm maximum (0) (lbf in) Case style D PK Case style TO-6 6CTQ...S 6CTQ...- Revision: 7-Feb-4 Document Number: 9445 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
VS-6CTQ...SPbF, VS-6CTQ...-PbF Series I F - Instantaneous Forward Current () 0 0 T J = 75 C T J = 5 C T J = 5 C 0. 0.4 0.6 0.8.0..4.6.8.0. V FM - Forward Voltage Drop (V) Fig. - Maximum Forward Voltage Drop Characteristics (Per Leg) I R - Reverse Current (m) 0 0. 0.0 0.00 T J = 75 C T J = 50 C T J = 5 C T J = C T J = 75 C T J = 50 C T J = 5 C 0.000 0 0 40 60 80 V R - Reverse Voltage (V) Fig. - Typical Values of Reverse Current vs. Reverse Voltage (Per Leg) 0 C T - Junction Capacitance (pf) T J = 5 C 0 0 40 60 80 V R - Reverse Voltage (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage (Per Leg) Z thjc - Thermal Impedance ( C/W) 0 0. Single pulse (thermal resistance) D = 0.75 D = 0.50 D = 0.33 D = 0.5 D = 0.0 0.0 0.0000 0.000 0.00 0.0 0. 0 t - Rectangular Pulse Duration (s) Fig. 4 - Maximum Thermal Impedance Z thjc Characteristics (Per Leg) Revision: 7-Feb-4 3 Document Number: 9445 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
VS-6CTQ...SPbF, VS-6CTQ...-PbF Series llowable Case Temperature ( C) 80 70 60 50 40 30 0 Square wave (D = 0.50) 80 % rated V R applied DC 0 See note () 0 4 6 8 0 4 verage Power Loss (W) 7 6 5 3 D = 0.0 D = 0.5 D = 0.33 D = 0.50 D = 0.75 4 RMS limit DC 0 0 4 6 8 0 I F(V) - verage Forward Current () I F(V) - verage Forward Current () Fig. 5 - Maximum llowable Case Temperature vs. verage Forward Current (Per Leg) Fig. 6 - Forward Power Loss Characteristics (Per Leg) I FSM - Non-Repetitive Surge Current () 0 t any rated load condition and with rated V applied following surge RRM 0 0 0 000 t p - Square Wave Pulse Duration (µs) Fig. 7 - Maximum Non-Repetitive Surge Current (Per Leg) L D.U.T. IRFP460 High-speed switch Current monitor R g = 5 Ω Freewheel diode 40HFL40S0 + V d = 5 V Fig. 8 - Unclamped Inductive Test Circuit Note () Formula used: T C = T J - (Pd + Pd REV ) x R thjc ; Pd = Forward power loss = I F(V) x V FM at (I F(V) /D) (see fig. 6); Pd REV = Inverse power loss = V R x I R ( - D); I R at V R = 80 % rated V R applied Revision: 7-Feb-4 4 Document Number: 9445 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
VS-6CTQ...SPbF, VS-6CTQ...-PbF Series ORDERING INFORMTION TLE Device code VS- 6 C T Q S TRL PbF 3 4 5 6 7 8 9 - product suffix - Current rating (6 ) 3 - Circuit configuration: C = Common cathode 4 - T = TO-0 5 - Schottky Q series 060 = 60 V 6 - Voltage ratings 080 = 80 V 7 - S = D PK - = TO-6 = V 8 - None = Tube (50 pieces) TRL = Tape and reel (left oriented - for D PK only) TRR = Tape and reel (right oriented - for D PK only) 9 - PbF = Lead (Pb)-free Dimensions Part marking information Packaging information SPICE model LINKS TO RELTED DOCUMENTS www.vishay.com/doc?9504 www.vishay.com/doc?95008 www.vishay.com/doc?9503 www.vishay.com/doc?9579 Revision: 7-Feb-4 5 Document Number: 9445 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T www.vishay.com/doc?90
Outline Dimensions D PK, TO-6 DIMENSIONS - D PK in millimeters and inches Conforms to JEDEC outline D PK (SMD-0) (3) L ()(3) E 4 c (E) (D) (3) Pad layout.00 MIN. (0.43) 9.65 MIN. (0.38) D L x e 3 H () x b x b C Detail 0.00 M M c ± 0.004 M E View - H (3) 7.90 (0.70) 5.00 (0.65).3 MIN. (0.08) Plating.64 (0.03).4 (0.096) (4) b, b3 3.8 MIN. (0.5) ase Metal Gauge plane Lead assignments Diodes. - node (two die)/open (one die)., 4. - Cathode 3. - node Lead tip 0 to 8 L3 L L4 Detail Rotated 90 CW Scale: 8: Seating plane (c) (b, b) Section - and C - C Scale: None c (4) SYMOL MILLIMETERS INCHES MILLIMETERS INCHES NOTES SYMOL MIN. MX. MIN. MX. MIN. MX. MIN. MX. NOTES 4.06 4.83 0.60 0.90 D 6.86 8.00 0.70 0.35 3 0.00 0.54 0.000 0.00 E 9.65 0.67 0.380 0.40, 3 b 0.5 0.99 0.00 0.039 E 7.90 8.80 0.3 0.346 3 b 0.5 0.89 0.00 0.035 4 e.54 SC 0. SC b.4.78 0.045 0.070 H 4.6 5.88 0.575 0.65 b3.4.73 0.045 0.068 4 L.78.79 0.070 0.0 c 0.38 0.74 0.05 0.09 L -.65-0.066 3 c 0.38 0.58 0.05 0.03 4 L.7.78 0.050 0.070 c.4.65 0.045 0.065 L3 0.5 SC 0.00 SC D 8.5 9.65 0.335 0.380 L4 4.78 5.8 0.88 0.08 Notes () Dimensioning and tolerancing per SME Y4.5 M-994 () Dimension D and E do not include mold flash. Mold flash shall not exceed 0.7 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L, D and E (4) Dimension b and c apply to base metal only (5) Datum and to be determined at datum plane H (6) Controlling dimension: inch (7) Outline conforms to JEDEC outline TO-63 Document Number: 9504 For technical questions within your region, please contact one of the following: www.vishay.com Revision: 3-Mar-09 Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com
Outline Dimensions D PK, TO-6 DIMENSIONS - TO-6 in millimeters and inches Modified JEDEC outline TO-6 (Datum ) () (3) E (3) L c E D Seating plane D(3) L C 3 C L () x e 0.00 M M Lead tip 3 x b 3 x b c Lead assignments Diodes. - node (two die)/open (one die)., 4. - Cathode 3. - node Plating c E Section - (4) ase b, b3 metal (b, b) (3) c (4) Section - and C - C Scale: None SYMOL MILLIMETERS INCHES MIN. MX. MIN. MX. NOTES 4.06 4.83 0.60 0.90.03 3.0 0.080 0.9 b 0.5 0.99 0.00 0.039 b 0.5 0.89 0.00 0.035 4 b.4.78 0.045 0.070 b3.4.73 0.045 0.068 4 c 0.38 0.74 0.05 0.09 c 0.38 0.58 0.05 0.03 4 c.4.65 0.045 0.065 D 8.5 9.65 0.335 0.380 D 6.86 8.00 0.70 0.35 3 E 9.65 0.67 0.380 0.40, 3 E 7.90 8.80 0.3 0.346 3 e.54 SC 0. SC L 3.46 4.0 0.530 0.555 L -.65-0.065 3 L 3.56 3.7 0.40 0.46 Notes () Dimensioning and tolerancing as per SME Y4.5M-994 () Dimension D and E do not include mold flash. Mold flash shall not exceed 0.7 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L, D and E (4) Dimension b and c apply to base metal only (5) Controlling dimension: inches (6) Outline conform to JEDEC TO-6 except (maximum), b (minimum) and D (minimum) where dimensions derived the actual package outline www.vishay.com For technical questions within your region, please contact one of the following: Document Number: 9504 Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com Revision: 3-Mar-09
Legal Disclaimer Notice Vishay Disclaimer LL PRODUCT, PRODUCT SPECIFICTIONS ND DT RE SUJECT TO CHNGE WITHOUT NOTICE TO IMPROVE RELIILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 07 VISHY INTERTECHNOLOGY, INC. LL RIGHTS RESERVED Revision: 08-Feb-7 Document Number: 90