(A4) 1/4-20 5mm Screw (x4) () 5/16-18 x 48mm Screw (x8) (A10) Neoprene Strip (x4) (A7) Leveler lide (x4) () 5/16-18 0mm Screw (x10) (A1) 4mm Allen Whrench (x1) (B1) M5 5mm Machine Screw (x4) (B2) M6 5mm Machine Screw (x4) (C1) 8mm D x 20mm OD Washer (x4) (C2) 6mm D 9mm OD Washer (x4) (C3) M3 Nut (x2) (C5) M5 Nut (x2) (A6) 5/16-18 Binding Post (x4) (A5) Adjustment Disc (x2) (D1) 5/16-18 x 40mm H Screw (x2) (D2) 1/4-20 5mm Screw (x4) (B3) M4 5mm Machine Screw (x4) (B4) 8mm D x 20mm OD Washer (x4) (C6) M6 Nut (x2) (C7) M3 5mm Machine Screw (x2) (C9) M5 5mm Machine Screw (x2) (A3) 5/16-18 lange Nut (x2) (B5) M8 5mm Machine Screw (x4) (B6) 6mm D 9mm OD Washer (x4) (C4) M4 Nut (x2) (C8) M4 5mm Machine Screw (x2) (C10) M6 5mm Machine Screw (x2) (D3) 4mm Allen Whrench (x1) (D4) 5mm Allen Whrench (x1) Component List Assembly Hardware (A) Totem - Model TV Mounting Hardware (B) (A2) 5mm Allen Whrench (x1) A - Assembly Hardware Kit B - TV Mounting Kit Your Totem Pedestal is engineered for easy assembly. Carefully follow this procedure to prevent any damage. Placement and Maintenance Totem is designed for indoor use on level floors. Clean steel and glass parts with a moist cloth. Tools Needed: Phillips Screwdriver bdiusa.com customerservice@bdiusa.com Soundbar Speaker Hardware (C) Totem - Model Shelf Assembly Hardware (D) Totem - Model C - Soundbar Speaker Kit D - Shelf Assembly Kit Step 1 Unpack and identify the components at left and below. The assembly workspace should be a non-marring surface such as carpet. or missing hardware pieces, please contact BD Customer Service at customerservice@bdiusa.com. or all other concerns, please contact your BD Retailer. - Swiveling Bracket x 2 N - Upper Cover Panel H - Horizontal Mounting Bracket - Vertical Mounting Bracket x 2 JL - Speaker Bracket Arm JR - Speaker Bracket Arm K - Universal Speaker Bracket - Vertical Column LL - Shelf Arm O - Lower Cover Panel LR - Shelf Arm M - lass Shelf E - Base Designed by Matthew Weatherly. These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. BD are trademarks of Becker Designed, nc. All Rights reserved. 2014, BD Made in China. 092614v1 1
Step 2 Screw Leveler lides (A7) into Base (E). A7 A7 A7 x 4 A7 E Step 3 With the Vertical Column () laying on its back, attach Base (E) using Screws () and 5mm Allen Wrench (A2), provided in Assembly Hardware Kit (A). E A2 5mm Allen Wrench x 4 2 E
Step 4 Rest the Assembly on its side and finish attaching Base (E) to Vertical Column () using Binding Post (A6) from the bottom of Base (E) and remaining Screws () from the top. Use both 5mm Allen Wrenches (A2 and D4) to tighten screws. A6 x 4 x 4 E A2,D4-5mm Allen Wrench A6 A6 A6 A6 E Step 5 Place Pedestal upright and attach each Swiveling Bracket () to top of Vertical Column () with Screws () and 5mm Allen Wrench (A2). NOTE: There are two (2) mounting-height positions to choose from. n general, for larger TV s (60 70 ) select the higher set of mounting holes, smaller TV s (45-60 ) select the lower set of mounting holes. A2 5mm Allen Wrench x 4 3
Step 6 Peel film from side of Neoprene Strip (A10) and attach to the outer edge of each Swiveling Bracket () as illustrated below. A10 A10 x 4 Neoprene Strip A10 Step 7 Attach Horizontal Mounting Bracket (H) to installed Swiveling Brackets () with Screws () and 5mm Allen Wrench (A2). 2 Person Task NOTE: Slots along Horizontal Mounting Bracket (H) must be at BOTTOM. Be sure to position Swiveling Bracket () so that each sits within recessed portion of the Horizontal Mounting Bracket (H). (Circled below) H A2 5mm Allen Wrench H x 4 4
Step 8 Position each Vertical Mounting Bracket () on back of TV and attach using mounting screws and washers (if required) provided in TV Mounting Kit (B). Each bracket must align vertically with the other. Both can be raised or lowered on back of TV at 1 increments. NOTE: Various mounting screws are provided in TV Mounting Kit (B), but some TVs may require specific hardware not provided by BD. n such cases, please contact your TV manufacturer to identify and source your hardware. nstall Leveling Disc (A5) onto threaded posts of Vertical Mounting Bracket (). A5 x 2 Step 9 With the help of another person, lift television with installed Vertical Mounting Brackets () and lower carefully onto Horizontal Mounting Bracket (H). 2 Person Task H A5 H 5
Step 10 Level the TV using the Leveling Discs (A5) near the slots in the lower Horizontal Mounting Bracket (H). Then secure into place using provided lange Nut (A3). A5 H A3 Step 11 nstall Speaker Bracket Arms (JL, JR) to Pedestal using Screws (A4) and 4mm Allen Wrench (A1). NOTE: There are several soundbar-height positions to choose from on 2 increments. The soundbar speaker should be located as close to the bottom of the TV as possible when attached. JR A1 4mm Allen Wrench A4 JL A4 JR A4 A4 6
Step 12 Position Universal Speaker Bracket (K) on back of speaker and attach using appropriate mounting screws and washers provided in Soundbar Speaker Kit (C). NOTE: Some speakers are not equipped with inserts to be attached to the Universal Speaker Bracket (K) and require the purchase of an additional bracket supplied by the speaker manufacturer. Attaching to Manufacturer s Bracket Attaching Directly to Speaker C Hardware Speaker Speaker Manufacturer s Speaker Bracket K K C Hardware Step 13 Loosely pre-install Screw () into Universal Speaker Bracket (K). Locate bodies of Screw () into groove of Speaker Bracket Arms (J) and tighten into place using 5mm Allen Wrench (A2). 2 Person Task NOTE: f the speaker position is either too close or too far away from the bottom of the TV, reposition Speaker Bracket Arms (J) to get desired spacing. TV J J K J K 7
Step 14 nstall Shelf Arms (LL, LR) to Pedestal using Screws (D2) and 4mm Allen Wrench (D3), provided in Shelf Assembly Kit (D). NOTE: There are several shelf-height positions to choose from on 2 increments to create appropriate clearance of components. LL D2 D2 LR LL D2 D2 Step 15 nstall lass Shelf (M) to Shelf Arms (LL, LR) using Screws (D1) and 5mm Allen Wrench (D4). Ensure the BD Label on lass Shelf (M) is oriented toward the back of the unit shown in ig. 15-1. 2 Person Task M D4 5mm Allen Wrench ig. 15-1 D1 D1 D1 x 2 8
Step 16 Wires can be passed under the wire management tray of the Vertical Column (). A power strip can be placed on the wire management tray of the Vertical Column (). Step 17 nstall Lower Cover Panel (O) with the magnets towards the top. O 9
Step 18 nstall Upper Cover Panel (N) by inserting tabs into the notches of the wire management tray. N N 10