Dust RIGHT Shop Vacuum Dust Hose Reel Instructions For safe and effective operation, please read these instructions fully before use.
GENERAL SAFETY WARNINGS This tool is designed for specific applications as defined in the instructions and should not be modified and/or used for any other applications. Before using the Shop Vacuum Dust Hose Reel read, understand and follow all instructions and safety information provided. KEEP THESE INSTRUCTIONS. > For any tool that is used in conjunction with this product always read, understand and follow the instructions and safety warnings for that tool. > Before using this product, review and verify that all tools used with it are in proper working order as defined by the tool s owner s manual. > All safety equipment must be installed and working properly as defined by the tool s owner s manual. > Do not use this product until you have read the provided instructions and warnings and are confident you understand them. > Always wear safety glasses in compliance with ANSI safety standards and hearing protection and follow all standard shop safety practices including: Keep your work area well lit and clean. Use dust collection tools and dust face masks to reduce exposure to dust. Use accessory safety equipment such as feather boards, push sticks, and push blocks whenever appropriate. Do not use power tools in explosive environments, e.g. in the presence of flammable liquids, fumes or dust. Keep children and bystanders away while operating your tools. Maintain proper footing at all times and do not overreach. Do not force the tool. Unplug all power tools before making any adjustments or changing accessories. > Remain alert and use good judgment when using this tool. Do not use this tool if you are in any way impaired by medications, alcohol, drugs or fatigue. > Dress appropriately and remove all jewelry, secure loose clothing and tie up long hair before using this tool. > It is the sole responsibility of the purchaser of this tool to ensure that any third party reads and agrees to all the safety precautions outlined in this manual prior to using the tool. > Maintain these instructions and warnings as long as you own the tool. Keep in a place where they will be readily available for reference. > The user assumes all risk for the proper use of this tool and for ensuring product suitability for intended application. > Do not attempt to lift more than you are physically able. Get help if necessary. Use proper lifting techniques. > These warnings and instructions do not represent the total of all information available regarding tool safety, use and technique. Always seek out opportunities to learn more and improve your skills and knowledge. SPECIFIC SAFETY WARNINGS > Failure to mount the Hose Reel according to the included instructions could result in personal injury or damage to property. > Do not mount the Hose Reel higher than your own shoulder height. > Do not leave uncoiled dust hoses on the floor as they can cause tripping hazards. > The Shop Hose Reel is intended for dry vacuuming only. Vacuuming wet materials will cause hose clogging > Do not hang or allow anyone else to hang from the Hose Reel. > Do not hang or coil objects other than the specified Shop Vacuum Hose from the Hose reel. 2
1 3 2 Base Assembly Assembly Base Assembly 1. Attach the Left Hub/Side Assembly (1) to the Base Plate (2), using 1/"-20 x /8" Panhead Screws () and 1/" Lock Nuts (). The Side Plate goes on the outside of the tabs on the Base Plate (2). 2. Attach the Right Side Plate (3) to the Base Plate (2), using 1/"-20 x /8" Panhead Screws () and 1/" Lock Nuts (). The Side Plate goes on the outside of the tabs on the Base Plate (2). PARTS LIST Quantity 1 Left Hub/Side Assembly 1 2 Base Plate 1 3 Right Side Plate 1 1/"-20 x /8" Panhead Screw 22 1/" Lock Nuts 22 3
PARTS LIST Quantity Quantity 6 Right Hub 1 7 Internal Flange Pivot 1 8 1/"-20 x 7/8" Flat-Head Screw 3 9 Right-Hand Swivel 1 10 1/"-20 x 3/" Flat-Head Screw 2 11 Four-Star Knob 1 12 Right-Hand Clamp 1 13 /16"-18 x 1 " Hex Bolt 1 1 Handle 1 1 /16-18 Lock Nut 1 16 Center Hub 1 17 Washer 1 18 Hose Retaining Strap 1 19 #8-32 x /8" Panhead Screw 1 20 #8-32 Lock Nut 1 21 3/8" x 2" Lag Screw 22 3/8" Washer 13 8 9 11 8 10 1 7 12 1 6 3 Right Hub Assembly - Shown without Base Plate (2) and Left Hub/Side Assembly (1) attached for clarity Right Hub Assembly 1. Working from the inside face of the Right Hub (6), fit the Internal Flange Pivot (7) through the center hole and attach, using three 1/"-20 x 7/8" Flat-Head Screws (8) and 1/"-20 Lock Nuts (). 2. From the other side of the Right Hub (6), slide the Right-Hand Swivel (9) onto the Internal Flange Pivot (7) until the narrow end of the Right-Hand Swivel (9) piece seats in the hole in the center of the Right Hub (6). 3. Fit the Right-Hand Clamp (12) onto the outside face of the Right Side Plate (3), using the center and fastener holes as a guide, and attach the clamp, using two 1/"-20 x 3/" Flat-Head Screws (10) and 1/"-20 Lock Nuts (). Thread the Four-Star Knob (11) into the Right-Hand Clamp (12), but don t tighten.. Position the Right Hub assembly on the inside of the Right Side Plate (3) so the Right-Hand Swivel is against the Right Side Plate and the Internal Flange Pivot (7) fits into the center hole and through the opening in the Right-Hand Clamp (12). Tighten the Four-Star Knob (11) to hold the assembly together (but don t overtighten).. From the inside of the Right Hub (6), insert the /16"-18 x 1 " Hex Bolt (13)through the Internal Flange Pivot (7). Thread the Handle (1) onto the hex bolt and secure with the /16"-18 Lock Nut (1).
9 9 16 17 17 19 17 18 20 Center Hub Assembly Center Hub Assembly 1. If you fully tightened the screws and nuts connecting the Right and Left Side Plates to the Base Plate, loosen them a bit to provide working space for installing the Center Hub (16). 2. Position the Center Hub (16) between the Right and Left Hubs, taking care to align the fastener holes/slots.. Retighten the screws and nuts connecting the Right and Left Side Plates to the Base.. Attach the Hose Retaining Strap (18) to the inside face of the Right Hub (6), using the #8-32 x /8" Panhead Screw (19), Washer (17) and #8-32 Lock Nut (20). 3. Attach the Center Hub (16) to the Right and Left Hubs, using 1/"-20 x /8" Panhead Screws (), Washers (17) and 1/"-20 Lock Nuts (). Work from the outside faces of the hubs, so that the screw heads and washers are on the outside and the nuts are against the flange of the Center Hub (16).
22 22 21 21 21 22 Fig. 1 Mounting to Wall Studs 1. The Hose Reel must be mounted to wall studs spaced 16" on center. 2. Mark the locations for the top two mounting screws and drill pilot holes for 3/8" x 2" Lag Screws (21). 3. Fit a 3/8" Flat Washer (22) onto each screw. Drive the screws into the studs until they re about 1" from being fully seated.. Decide whether you want the Handle of the Hose Reel to be on the right or the left side. Orient the Hose Reel as desired and lift it onto the top two 3/8" x 2" Lag Screws (21). Fig. 1.. Mark the locations for the bottom two 3/8" x 2" Lag Screws (21), using the bottom keyhole slots in the Base Plate (2) as a guide. 6. Lift the Hose Reel off the top two Lag Screws (21) to remove it. Drill pilot holes for the lower set of Lag Screws (21). 7. Return the Hose Reel onto the top two Lag Screws, making sure that the 3/8" Washers (22) make it through the keyhole openings in the Base Plate (2). Check that the Hose Reel is level and then drive the 3/8" x 2" Lag Screws (21) until they are fully tightened. Fig. 1. Inset. 8. Fit a 3/8" Flat Washer (22) onto each of the remaining two 3/8" x 2" Lag Screws (21) and drive the screws into the lower two pilot holes to fully secure the Hose Reel. Fig. 2 6
Fig. 3 Attaching Hoses 1. Attach your 11 2" hose to a port that has a 21 " outside diameter on one end. 2. Press the 21 " OD end of the port into the Shop Vacuum Port on the inside of the Hose Reel. Fig. 2. 3. Unscrew the Hose Retraining Strap (18) from the Right Hub (6) and fit the strap around the hose.. Make sure there s enough slack in the hose to prevent kinking and reattach the Hose Retraining Strap (18) to the Right Hub (6). Fig. 3.. The Shop Vacuum Port on the outside of the Hose Reel has an OD of 21 2" and an ID of 21 ". You can fit 21 2" hose directly onto the port and secure it with a hose clamp, or you could use a fitting like the 21 2" Swivel Fitting for Shop Vacs (31660, sold separately). Controlling Unwinding Speed 1. Once the 11 2" hose is connected, loosen the Four-Star Knob (11) and use the handle to wind the hose fully onto the Hose Reel. The reel can accommodate up to 0' of 11 2" hose. 2. Gently pull the hose to begin unwinding. Tighten or loosen the Four-Star Knob (11) to adjust the resistance. Fig.. 11 Check Rockler.com for updates. If you have further questions, please contact our Technical Support Department at 1-800-260-9663 or support@rockler.com Fig. 7
22 Rev 01/17 Distributed by Rockler Companies, Inc. 2017 Rockler Woodworking and Hardware