Full-motion Wall Mount MD120409-01 AWM1521- AU
Safety Instruction Component Checklist WARNING IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If any parts are missing or faulty, telephone your local distributor for a replacement. NOTE: Read the entire instruction manual before you start installation and assembly. Do not begin the installation until you have read and understood the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instruction or warning, please contact your local distributor. decorative cover (x2) C cable cover (x1) E This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. articulated arm assembly A cable dip (x1) G This product should only be installed by someone of good mechanical ability, with basic building experiences and fully understanding of this manual. extension bar (x 2) B middle decorative cover (x1) D wall template (x1) F M4 (x1) H Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Package M If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of a stud finder is highly recommended. M4x14 (x4) M-A M5x14 (x4) M-B M6x14 (x4) M-C M8x15 (x4) M-D Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power. D4 washer M-E (x4) D (x4) M-F 5 washer D6 washer (x4) D8 washer (x4) M-G M-H This product intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. ø13.5xø5.5x3.2 (x4) M-I M6 (x4) M-J 4mm allen key (x1) M-K Package W ST6.3x55 (x4) W-A concrete anchor (x4) W-B D6 washer (x4) W-C
Disassemble VESA Plate 2. Mount on Solid Brick and Concrete Block loosen 60mm (2.4") ø 10mm (ø 3/8") remove 1 1. Mount on Wood Stud Wall 55mm (2.2") With arrow head pointing up 2 ø 4.5mm (ø 3/16") 1 Drill pilot holes With arrow head pointing up 2 W-B W-C W-A 3 W-C Drill pilot holes W-A Screw the wall mount onto the wall WARNING Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder is highly recommended. Installers are responsible to provide hardware for other types of mounting situations. Screw the wall mount onto the wall Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. WARNING When installing wall mounts on cinder block, verify the actual concrete thickness is at least 1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block. It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
3. Installing Decorative Covers 5. Install VESA Plate Top of Insert both top and bottom plastic covers Then install the middle decorative cover. 4. Assemble VESA Adaptors M-J M-C/M-D M-G/M-H or M-A/M-B M-E/M-F M-I Screw the VESA plate onto the. Tighten all screws but do not over tighten.
6. Hook the onto the Wall Mount 7. Cable Management 4mm Attach cable clip to the arm using appropriate screw. H G E Loosen the upper flat nut spacing 4mm to VESA plate. Hook the onto the wall mount Connect cables to your and route cables through cable clip, then attach the cable cover to hold the cable in place. Note: Leave slack in cable for cantilever arm movement. 8. Adjustment 180 180 +3-3 +15-15 Level the. Place the lower flat nut, tighten both flat nuts. Adjust to the desired location or tilt.
9. Adjustment M-J According to the different weight of the display, it is necessary to slightly loosen or tighten the adjustment screw using the supplied Allen key. Maintenance Check that the bracket is secure and safe to use at regular intervals(at least every three months). Please contact your dealer if you have any questions.