Assembly instructions for EZ Hang Deluxe EZ Hang Chairs is pleased that you have chosen our EZ Hang Deluxe. While utmost care is taken in the choice of materials and the highest standards are used in manufacturing, caring for your chair at home will extend its life and appearance. Assembly Locate all your EZ Hang Deluxe Chair parts. Including: a) cushion piece (1) b) footrest (1) c) a set of round spreader bars (2) d) a set of bent arms attached to overhead square bar via ropes (1) e) hardware pack wrapped inside cupholder (4) Place wooden bent arms on the ground making sure the arms are face up and that the ropes are not twisted or turned impeding the next step. First insert the rope through the hole on the back of the bent arms and tie a small knot (The brake should be on the back side / if they are on front simply untie the front knot and reverse the clips to the back side).
Place the cushion part of the chair with the EZ Hang logo at top right in between the bent arms on the ground. Thread the two round spreader bars through the sleeves underneath the cushion (one sleeve is on top and bottom of the main cushion). Connect the cut away section of the round spreader bars onto the top matching section of the bent wood arms. (Refer to picture to make sure that the bent wood arms are set correctly). Using the hardware provided connect the round spreader bars to the bent wooden arms by placing the hexbolt through the spreader bar and bent wood arms from front to back. Bolt down firmly using the washer and nut. Repeat this procedure in all four corners of the chair. Use the wrench to tighten the bolt until it is flush with the front side of the wood. Installing eyebolt Locate ceiling joist (use stud finder or tap and verify with small nail). Be sure to locate the exact center. Predrill a starter hole using a 3/16 drill bit. Screw in the supplied eyelag until all that is visible is round section. Do not loosen or adjust once in place. Caution (swinging could loosen the eyebolt and compromise the sturdiness). Fine tuning adjustment Your chair can be adjusted back and forward by manipulating the ropes on the overhead square bar. The brakes must be on the back side of the square bar and must sit tight against the square bar once the recline has been set. Washing and care instructions Using a soft brush and warm soapy water, scrub where dirty. Allow to dry hanging or on a flat surface. Disclaimer Please note: Manufacture, Seller, Distributer and all agents or reps thereof cannot assume responsibility for special, indirect, or consequential damages or contingent liability for use of this product in a manner not expressly intended by the manufacturer. End consumer is ultimately responsible for verifying proper installation of the eyelag/ hook assembly according to guidelines explained here within.
EZ Hang Loveseat Spreader Bar instructions (Spreader Bar is NOT for hanging the loveseat - see below) Your EZ Hang Love Seat comes with hanging hardware and chain suitable for most standard porch swing frames, such as our own Roman Arch wooden frame (pictured at left). You may, however, choose to hang yours from a tree limb, porch overhang, or other suitable structure. Should you decide to hang your loveseat from a taller structure, you can purchase chain in the proper length and gauge at any hardware store. Make sure you observe our own 500 lb rating when selecting additional chain and/or hardware, and that you hang your loveseat from a structure capable of handling that weight. We have included a 51 wooden spreader bar and 4 mini eyelag bolts to provide a hang point for the footrests in taller support configurations, and/or to support the optional rain cover. When hanging your Love Seat from a hang point taller than 66, make use of the spreader bar as a secondary support point. Install as follows: Insert two of the eyelags into the outermost holes of the spreader bar with the eyes up. Insert the remaining two eyelags into the two centermost holes, eyes down. Secure the eyelags with the washer next to the nut, and tighten all nuts securely. Insert two S-hooks into the outer, up-hanging eyes, and hang the spreader bar 6-12 above the O- rings tied to each side of the supporting ropes on the Love Seat. Tie or hang the footrests to the inner, down-hanging eyes as shown. IMPORTANT: The supplied mini-eyelags and spreader bar are NOT designed to bear the weight of the Love Seat itself, or of any person, and should NOT in any way be inserted into the weight bearing system. Do NOT hang any supporting rope, chain, or the Love Seat off of the mini eyelags or spreader bar.
Instructions Assembly Hammock Chair Eyebolt Installation Find ceiling joist (use stud finder or tap and verify with small nail). Be sure to locate the exact center. Drill a hole using a 3/16 drill bit perpendicular to ceiling. Screw in the included eyebolt/hook assembly until all threads are not visible. Do not loosen or adjust once installed. Hole must be directly in the center of the stud for full weight bearing capacity. Spinning or swinging could loosen and compromise the eyebolt strength. Hanging Hammock Chair Hang the Hammock Chair by the O ring onto the pre-installed eyebolt/hook. Washing Instructions Scrub gently with a soft brush and a mixture of water and soap. Using a fabric protector will enhance the look of your chair longer. No machine wash. Disclaimer Culture Shock Trading company INC and all agents thereof cannot assume responsibility for special, indirect, or consequential damages, injury, or contingent liability for use of this product in a manner not intended by manufacturer. End consumer is ultimately responsible for Verifying proper install of eye-bolt according to guidelines here within.
ROMAN ARCH INSTRUCTIONS CONTENTS LIST HARDWARE 1. Top Arch Piece 5. 4 ½ Bolt Assembly Set 2. Straight Lower Leg Supports 6. 8 ½ Bolt Assembly Set 3. Arch Support (Slightly Curved) 7. 6 Eyebolt Assembly Set 4. Curved Legs 8. Eyebolts for use with two separate chairs on the arch ESSENTIAL TIPS FOR ASSEMBLY: a. Use 2 people to assembly Roman Arch b. Hand tighten bolts until completely assembled, then tighten all the way. c. Use pictures often for assembly referral d. Straight leg supports go on outside of arch e. Arch support piece has two sides. One side has a sharp angle and one side has short angle. ASSEMBLY STEPS: Connect lower leg support with two curved legs at the bottom using # 5 (4 ½ bolt assembly.) Straight Lower Leg Support Attach one end of Arch Support (# 3) to previously assembled curved legs (#6) using 8 ½ bolt assembly. NOTE: The short angled side of the arch support goes in between the legs.) Slightly Curved Arch Support Repeat lower leg support and arch support assembly for other side of Arch. Page 1
Connect 2 previously assembled leg pieces with top arch piece (#1) using 8 ½ bolt assembly (#5.) NOTE: Refer to pictures to assist in Set up. Top Arch Piece Assembled Leg Pieces Connect long angled side of arch support to top arch piece using 6 Eyebolt assembly set (#7.) NOTE: The loveseat hangs from this 6 eyebolt on each side.) Long Angled side of Arch Support Tighten all bolts completely tight. Page 2
Assembly instructions for Frame Parts Included: (1) X Section of Frame (2) Lower Section of Frame (3) Top Section of frame (4) 2 additional side support brackets (5) Hardware Pack, Tool, Instructions Assembly Instructions (6) Insert lower section of frame into the center hole of X section. Connect the two sections using the long bolt in the top hole and short bolt in bottom hole. The top long bolt goes all the way through when completely tightened. Tilting the frame forward can assist in correctly aligning bolts. (7) Connect top section to the lower section and align holes and tighten completely with the two allen bolts. (8) If desired attach two side support brackets to the X section of the frame using the hardware included. (9) Hang chair from Hook point at top of upper section.
Care It may be necessary to spray frame occasionally with rust preventative spray paint to enhance appearance. Reminder The frame is not intended to swing or twist in. Always exit frame front to back and not sideways. Use caution. Disclaimer Destin Trek Imports and all agents thereof cannot assume responsibility for special, indirect, or consequential damages, injury, or contingent liability for use of this product in a manner not intended by manufacturer. End consumer is ultimately responsible for verifying proper assembly of frame.