Information METALLAMAT Adjustment options Lateral adjustment Adjusting on concealed hinge + mm Height adjustment Via mounting plates adjusting ± 2 mm Depth adjustment Adjusting on concealed hinge + 4 mm, -1 mm Processing and mounting deviations can be corrected with the three-dimensional adjusting facility. Factory settings For lateral, height and depth adjustment: Zero position Mounting Hinge arm height with mounting plate Mounting methods Hinge arm length Door offset Door overlay Distance to cup Gap Concealed hinge with straight hinge arm Half overlay mounting Concealed hinge with cranked hinge arm Inset mounting Concealed hinge with high cranked hinge arm Number of concealed hinges per door The values in the table are sample measurements. A trail mounting is recommended. The number of concealed hinges per door depends on: Door width and height Door weight Door material According to the example diagram, with a door height of 1,500 mm and a door weight of 7-12 kg, three concealed hinges have to be fitted. Height 2500 2000 1500 1000 4 5 500 6 9 10 15 16 22 500 500 500 kg 500 2 4 5 Number of hinges Choice of mounting plate Distance The different spacing heights of the mounting plates allow adjustments to be made to the door overlay. The dimension of the Door overlay results from the thickness of the mounting plate. Gap Distance to cup The starting point for determining the required is the required mounting method with a defined door overlay. Example Door overlay mm 4 5 6 7 8 9 10 11 12 1 4 5 6 7 4 5 6 7 4 4 5 6 7 6 4 5 6 7 8 Distance to cup mm mm Once the door overlay and the to cup have been determined, the can be looked up in the application table. In the example the door overlay is defined at 10 mm and the to cup at 5 mm. This produces a of 4 mm. HMA.5
METALLAMAT A Concealed hinge, opening angle 110 Material: Steel cup and hinge arm For door thickness: 16 22 mm Fixing door to carcase: Slide on system Adjusting facility: -dimensional (with appropriate mounting plate) With automatic closing spring and push version Cup dimensions Drilling dimensions for cup fixing Screw fixing 16.0.500 Screw fixing push version 16.0.800 Half overlay mounting Inset mounting Screw fixing 16.0.501 Screw fixing push version 16.0.801 Screw fixing 16.0.502 Screw fixing push version 16.0.802 HMA.6
METALLAMAT A Concealed hinge, opening angle 92 Material: Steel cup and hinge arm For door thickness: Min. 22 mm Fixing door to carcase: Slide on system Adjusting facility: -dimensional (with appropriate mounting plate) With automatic closing spring Cup dimensions Drilling dimensions for cup fixing Screw fixing 16.1.500 Half overlay mounting Screw fixing 16.1.501 Inset mounting Screw fixing 16.1.502 HMA.7
METALLAMAT A Concealed hinge, opening angle 175 Material: Steel cup and hinge arm For door thickness: 16 22 mm Fixing door to carcase: Slide on system Adjusting facility: -dimensional (with appropriate mounting plate) With automatic closing spring Cup dimensions Drilling dimensions for cup fixing Screw fixing 16.2.600 Half overlay and inset mounting Half overlay mounting Inset mounting Set back mounting plate screw-on position by door thickness. Screw fixing 16.2.601 HMA.8
Accessories for METALLAMAT A Concealed hinge METALLAMAT A Cruciform mounting plate, slide on system Material: Steel Adjusting facility: Height adjustment via slot Screw fixing, with chipboard screws Drilling dimensions Distance D 2 mm 16.51.502 4 mm 16.51.504 6 mm 16.51.506 8 mm 16.51.508 Screw fixing, with pre-mounted special screws into 2 mm series drilled holes Drilling dimensions Distance D 4 mm 16.51.524 6 mm 16.51.526 METALLAMAT A Cover cap Order information Cover caps can be individually printed from minimum order quantity of 100,000. METALLAMAT Soft closing device Material: Steel : With HÄFELE logo or without logo or with individually print Without logo or with individually print 16.6.500 With HÄFELE logo 16.6.510 Packing: 1 or 5,000 pcs. Material: Plastic Finish Nickel plated 16.5.70 Information Unusable with METALLAMAT A concealed hinge opening angle 175 and pushing hinges. HMA.9
METALLAMAT SM Concealed hinge, opening angle 110 Material: Steel cup and hinge arm For door thickness: 16 22 mm Adjusting facility: -dimensional (with appropriate mounting plate) Installation: Screw fixing 18.40.500 Half overlay mounting 18.40.501 Inset mounting 18.40.502 METALLAMAT SM Concealed hinge, opening angle 92 Material: Steel cup and hinge arm For door thickness: Min. 22 mm Adjusting facility: -dimensional (with appropriate mounting plate) Installation: Screw fixing 18.41.600 Half overlay mounting 18.41.601 Inset mounting 18.41.602 Packing: 1 or 200 pcs. METALLAMAT SM Concealed hinge, opening angle 175 Material: Steel cup and hinge arm For door thickness: 16 22 mm Adjusting facility: -dimensional (with appropriate mounting plate) Installation: Screw fixing Accessories for METALLAMAT SM Concealed hinge METALLAMAT SM, clip on system without screws 18.42.600 Half overlay mounting 18.42.601 Packing: 1 or 100 pcs. Material: Steel : Reversible Height Without screws With Euro screws mm 18.61.50 18.61.52 4 mm 18.61.504 18.61.524 6 mm 18.61.506 18.61.526 HMA.10
METALLAMAT A Concealed hinge, clip on system Material: Steel cup and hinge arm For door thickness: 16 22 mm Adjusting facility: -dimensional (with appropriate mounting plate) Installation: Screw fixing 18.70.500 Half overlay mounting 18.70.501 Inset mounting 18.70.502 Accessories for METALLAMAT A Concealed hinge, clip on system METALLAMAT A without wing shape Material: Steel Distance of adjustable: 2 mm left and right 18.80.504 Half overlay mounting 18.80.506 Inset mounting 18.80.508 Packing: 1 or 500 pcs. METALLAMAT A with wing shape Material: Steel Distance of adjustable: 2 mm left and right, 1.5 mm up and down 18.81.504 Half overlay mounting 18.81.506 Inset mounting 18.81.508 Packing: 1 or 500 pcs. HMA.11
METALLAMAT MINI SL Concealed hinge, opening angle 92 Material: Cup and hinge arm made of steel Fixing door to carcase: Hooking-in system Adjusting facility: -dimensional (with appropriate mounting plate) With automatic closing spring Cup dimensions Drilling dimensions for cup fixing Screw fixing 17.01.505 Packing: 1 or 500 pcs. Half overlay mounting Screw fixing 17.01.514 Packing: 1 or 500 pcs. Inset mounting Screw fixing 17.01.52 Packing: 1 or 500 pcs. METALLAMAT MINI SL Screw fixing, with chipboard screws Drilling dimensions Screw fixing, with pre-mounted special screws into 2 mm series drilled holes Drilling dimensions Height 2 mm 17.9.602 5 mm 17.9.605 Height 2 mm 17.9.612 HMA.12
METALLAMAT Concealed hinge, opening angle 105 Installation Material: Steel cup and hinge arm For door thickness: 16 22 mm Adjusting facility: -dimensional (with appropriate mounting plate) A K mm 4 mm 5 mm 6 mm H 0 mm 15 mm 16 mm 17 mm 18 mm 2 mm 1 mm 14 mm 15 mm 16 mm 4 mm 11 mm 12 mm 1 mm 14 mm Screw fixing 1.00.101 Packing: 1 or 500 pcs. Half overlay mounting Inset mounting A K mm 4 mm 5 mm 6 mm H 0 mm 6 mm 7 mm 8 mm 9 mm 2 mm 4 mm 5 mm 6 mm 7 mm 4 mm 2 mm mm 4 mm 5 mm Screw fixing 1.00.102 Packing: 1 or 500 pcs. A K mm 4 mm 5 mm 6 mm H 0 mm mm 2 mm 1 mm 0 mm 2 mm 5 mm 4 mm mm 2 mm 4 mm 7 mm 6 mm 5 mm 4 mm Screw fixing 1.00.10 Packing: 1 or 500 pcs. HMA.1
METALLAMAT for hinges with opening angle 105 Drilling dimensions Material: Steel : Screw fixing Height 0 mm 1.10.500 2 mm 1.10.502 4 mm 1.10.504 METALLAMAT MINI SL Glass hinge, opening angle 92 Material: Plastic cup, steel hinge arm Finish: Cup black, hinge arm nickel plated : Screw fixing Fixing door to carcase: Hooking-in system For glass thickness: 4 5 mm Adjusting facility: -dimensional (with appropriate mounting plate) With automatic closing spring Cup dimensions Drilling dimensions for cup fixing 17.02.500 Half overlay mounting 17.02.501 Inset mounting 17.02.502 Packing: 1, 50 or 500 pcs. HMA.14
METALLAMAT MINI SL Front plate Material: Plastic Supplied with: Plastic intermediate layer and fixing screws Oval Finish Chrome plated polished 17.10.410 Gold plated polished 17.10.510 Black 17.10.10 Packing: 1 or 100 pcs. Round R5 2 8 Finish Chrome plated polished 17.10.420 Gold plated polished 17.10.520 Black 17.10.20 Packing: 1 or 100 pcs. METALLAMAT MINI SL Material: Steel Hole spacing: 2 mm Screw fixing, with chipboard screws Drilling dimensions Height 2 mm 17.9.602 5 mm 17.9.605 Screw fixing, with pre-mounted special screws into 2 mm series drilled holes Drilling dimensions Height 2 mm 17.9.612 HMA.15
METALLA Concealed hinge, cup Ø 5 mm, opening angle 110 Material: Steel Finish: Galvanized : Screw fixing Fixing door to carcase: Clip-on system For door thickness: 16 22 mm Adjustment: -dimensional 11.90.500 Half overlay mounting Half overlay mounting 11.90.501 Inset mounting Inset mounting 11.90.502 HMA.16
METALLA, clip-on system Material: Steel Finish: Galvanized Adjusting facility: Height adjustment via slot Distance D 0 mm 11.98.500-2 mm 11.98.505 With pre-installed mounting screws Distance D 0 mm 11.98.510 With 4 screwholes Distance D -2 mm 11.98.565 HMA.17
METALLA ECONO MINI Hinge, cup Ø 26 mm Material: Steel : Screw fixing Fixing door to carcase: Slide on system -dimensional (with appropriate mounting plate) With automatic closing spring Drilling dimensions for cup fixing Cup dimensions Screw fixing 11.20.500 Half overlay mounting Screw fixing 11.20.501 Inset mounting METALLA ECONO MINI, slide-on system Screw fixing 11.20.50 Material: Zinc Finish: Galvanized Height 2 mm 11.0.502 HMA.18
Door damping system for mounting in drilled hole with or without adapter Installation into cabinet top or/and base Material: Plastic Installation instructions Drill hole with Ø 10 mm, at least 50 mm deep. Insert damping into drilling. Colour Grey 56.7.650 Installation information Insert damping into middle of top panel or base. For doors above a height of 1,600 mm or doors with aluminium and wooden frames it may be required to use 2 dampings, which have to be inserted into top panel or base. Cross adapter, screw fixing with chipboard screws Ø.5 mm With positioning aid Without positioning aid Drilling 28 x 2 mm Without positioning aid With positioning aid Material: Zinc alloy With positioning aid 56.7.660 Without positioning aid 56.7.661 Material: Plastic Colour: Grey With positioning aid 56.7.560 Without positioning aid 56.7.561 HMA.19
Drilling 7 x 2 mm Material: Zinc alloy With positioning aid 56.7.670 Without positioning aid 56.7.671 Without positioning aid Material: Plastic Colour: Grey With positioning aid 56.7.570 Without positioning aid 56.7.571 With positioning aid Cross adapter, screw fixing with chipboard screws Ø 6 mm With positioning aid Without positioning aid Drilling 28 x 2 mm With positioning aid Drilling 7 x 2 mm Without positioning aid Material: Plastic Colour: Grey With positioning aid 56.7.580 Without positioning aid 56.7.581 Material: Plastic Colour: Grey With positioning aid 56.7.590 Without positioning aid 56.7.591 HMA.20
Door damping system Information Opening by gentle push the front No handle is necessary to open and close the door Hinge without automatic closing facility required Installation of pin should be near the touching area of door No door adjustment problem because a large magnetic catch range is available Installation Plug in buffer in adapter plate Plug in buffer in drilling of carcase front side edge TOUCH LATCH SENSO Buffer incl. magnet Drilling dimensions Type 61769 56.0.500 Packing: 1 or 100 pcs. Adapter plate, straight Drilling dimensions Area of application: For carcase with thudding door, for taking on Airmatic buffer Installation: Screw fixing with chipboard screws Type 609 56.1.50 Packing: 1 or 25 pcs. HMA.21
REGULA Hinge arm attachment Screw fixing Press fitting Flat arm inside Outside with exposed axle * A third screw is essential for securing the arm REGULA: Screw fixing - with pre-mounted special screws - with chipboard screws Press fitting - with pre-mounted spreading dowels in 2 mm series drilled holes Mounting door at carcase Dismounting door at carcase Sliding on technics Slide hinge arm anto cup Tighten screw Unscrew Subtract cup from the hinge arm Adjustment possibilities Processing and mounting deviations can be corrected with the two and three-dimensional adjustment possibility. Lateral, height and depth adjustment attuned ex works in null position. Lateral adjustment Height adjustment Regula SM with 2-dimensional adjustment mm via eccentric ± 2 mm via slots HMA.22
Calculation of door width Legend CCW = clear cabinet width DO = door overlay DW = door width G = gap External cabinet width 800 mm Side panel width 2 x 19 mm 8 mm Clear cabinet width 762 mm Carcase with double door CCW + (2 x DO) (1 x G) 2 Example = door width 62 + (2 x 16 mm) (1 x 6 mm) = 94 mm 2 Number of concealed hinges per door Specifications at table are reference values for doors up to width 600 mm. The numbers of hinges for doors with width lower than 400 mm must be calculated via mounting trial. Trial mounting will be recommended. Doors should not be wider as high. Door width max. 600 mm. The number of concealed hinges per door depends on: Door width and height Door weight Door material For strong weight loads an additional hinge to install approx. 100 mm below the upper hinge will be recommended. Mass X = Max. 100 mm As per sample drawing for door height of 2000 mm and door weight of 17 kg are provided three concealed hinges. For concealed hinge with gap 6 mm Height Numbers of hinges HMA.2
REGULA Concealed hinge for wooden doors, 6 mm gap Material: Zinc alloy cup and hinge arm Arm fixing: For screwing into 2 mm series drilled holes or press fitting Installation: Door to cabinet with slide-on system Side panel thickness: 19 mm Door thickness: Max. 20 mm Adjusting facility: Height and lateral adjustment With spring Installation dimension Drilling pattern for arm fixing Drilling pattern for cup fixing, drilling pattern 48/6 Screw fixing/press fitting (drilled hole Ø 5 mm) Screw fixing Press fitting Opening angle: 250 Door overlay: 1 mm Arm fixing Drilling pattern 48/6 Screw fixing Screw fixing 44.21.000 Screw fixing with pre-mounted special screws Ø 5 mm 44.21.010 Press fitting with premounted spreading dowels Ø 5 mm 44.21.020 Side panel mounting Twin mounting Opening angle: 180 Door overlay: 6.5 mm Arm fixing Drilling pattern 48/6 Screw fixing Press fitting with pre-mounted spreading dowels Ø 5 mm 44.21.021 Screw fixing with pre-mounted special screws Ø 5 mm 44.21.011 Screw fixing 44.21.001 Opening angle: 180 Door overlay: 6.5 mm Arm fixing Drilling pattern 48/6 Screw fixing Press fitting with pre-mounted spreading dowels Ø 5 mm 44.21.02 Screw fixing with pre-mounted special screws Ø 5 mm 44.21.01 Screw fixing 44.21.00 HMA.24
REGULA Concealed hinge for glass doors, 6 mm gap Installation dimension Material: Zinc alloy cup and hinge arm : Screw fixing Arm fixing: For screwing into 2 mm series drilled holes or press fitting Installation: Without tools (quick fixing system) Side panel thickness: 19 mm For glass thickness: 4 6 mm Adjusting facility: Height and lateral adjustment With spring Drilling pattern for cup fixing Drilling pattern for arm fixing Screw fixing, drilling pattern 48/6 Screw fixing/press fitting (drilled hole Ø 5 mm) Opening angle: 250 Door overlay: 1 mm Arm fixing Screw fixing Press fitting with pre-mounted spreading dowels Ø 5 mm 44.2.020 Screw fixing with pre-mounted special screws Ø 5 mm 44.2.010 Screw fixing 44.2.000 Half overlay mounting Twin mounting Opening angle: 180 Door overlay: 6.5 mm Arm fixing Screw fixing Press fitting with pre-mounted spreading dowels Ø 5 mm 44.2.021 Screw fixing with pre-mounted special screws Ø 5 mm 44.2.011 Screw fixing 44.2.001 Opening angle: 180 Door overlay: 6.5 mm Arm fixing Screw fixing Press fitting with pre-mounted spreading dowels Ø 5 mm 44.2.02 Screw fixing with pre-mounted special screws Ø 5 mm 44.2.01 Screw fixing 44.2.00 HMA.25