MONOGRM 48" UILT-IN SI-Y-SI RFRIGRTOR STION 1 STNR INSTLLTION 1/4" FRM PNLS 3/4" OVRLY PNLS STION 2 FLUSH INST INSTLLTION
STNR INSTLLTION 25 1/2" (64.8) 48" (121.9) 23 7/8" (60.7) 1 3/4" (4.4) *84" (213.4) *83 1/2" (212.1) 68 1/2" (174.0) *72 1/4" (183.5) SPIFITIONS Overall Width Overall Height Overall epth oor learance utout Width 48" (121.92 cm) 84" (213.36 cm) 25 3/8"(64.453 cm) 28 5/8" (72.1 cm) 47 1/2" (120.7 cm) utout Height 83 1/2" - 84 1/2" (212.1-214.6 cm) utout epth Plumbing Requirements Shipping Weight 24" (61 cm) 1/4" O copper tubing or G Smartonnect kit 775 lb *3 3/4" (9.5) FRONT VIW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. ** llow 15" (38.1) min clearance for 130 door swing 47" (119.4) ase width *3 1/2" SI VIW ** llow 20" (50.8) min clearance for 130 door swing TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. ** llow 4" (10.2) min clearance to a wall for 90 door swing TOP VIW ** llow 4" (10.2) min clearance to a wall for 90 door swing 28 5/8" (72.7) ** These refrigerators are equipped with a 2-position door stop. The factory-set 130 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow full 130 door swings for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
STNR INSTLLTION TOP VIW STNR INSTLLTION 3 1/8" 24" (61) (7.93) 47 1/2" (120.7) 7/16" (1.1) 1 9/16" Trim overlap (3.97) SI VIW W 3 1/2" *84 1/2" (214.6) *Trim will overlap additional 7/16" 5" (12.7) 6" (15.24) 5" (12.7) WTR FRONT VIW 20" (50.8) 5" (12.7) The refrigerator will project forward, slightly beyond adjacent cabinetry. 75" (190.5 ) From floor to bottom of electrical area 3 1/2" Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. etermine your installation construction and required anti-tip configuration: Installed Under Soffit NTI-TIP RKT SOFFIT 2" x 4" ut to 35" Length fter installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit. SI VIW INSTLL UNR SOFFIT *84" (213.4) *Or installation height from floor SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X Screws mounted into vertical wall studs Top ase Trim Install Screws Through Trim and Into 3/4" Min. Wood race FRONT VIW INSTLL WITH MTL WLL STUS N NO SOFFIT 3/4" Min. Side View Top ase Trim Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. Metal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it s front surface 24" from back wall. fter installing unit into opening, raise grille panel and attach metal case top trim to 3/4" minimum wood brace. The brace spanning the enclosure must be securely fastened to cabinets on both sides. See Installation Instructions for detailed instructions.
USTOM SI PNLS F 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *epending on installation height STNR INSTLLTION F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and lo op fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6-10.2) *epending on installation height 2 9/16" (6.5)
1/4" FRM PNL IMNSIONS Freezer Grille Fresh Food PNL SSMLY ROSS STION Trim 1/4" Framed PNL IMNSIONS oor Supplied Handles 1/4" Framed 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16" STNR INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed s: For 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs 3/4" OVRLY PNL IMNSIONS Freezer Grille Fresh Food PNL SSMLY ROSS STION Trim 1/4" acker.10" Spacer PNL IMNSIONS oor 3/4" Overlay Supplied Handles 1/4" acker 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16".10" Spacer 45" 8 5/8" 67" 17 1/4" 25 1/4" 3/4" Overlay 46 1/8" 9 3/4" 68 5/8" 18 13/16" 26 13/16".25" +.10" +.75" = 1.10" Total Thickness 3/4" Overlay s: For 3/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOT: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs oor Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle. Order 2 kits for side-by-side refrigerators from your Monogram supplier.
FLUSH INST INSTLLTION 50" (127.0) 26" (66.0) 20 5/8" (52.4) 11 11/16" (29.7) 84 1/2" (214.6) 72 5/8" (184.5) * 83 1/2" (212.1) 68 5/8" (174.3) SPIFITIONS Overall Width 50" (127.0 cm) Overall Height 84 1/2" (214.6 cm) Overall epth 26" (66.0 cm) oor learance utout Width utout Height utout epth Plumbing Requirements Shipping Weight 28 5/8" (72.1 cm) 51" (129.5 cm) 85" (215.9 cm) 26 3/16" (66.5 cm) 1/4" O copper tubing or G Smartonnect kit 775 lb (351.5 kg) FRONT VIW Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84". **15" (38.1) 47" (119.4) ase width 4" (10.2) SI VIW **20" (50.8) imensions include 3/4" custom cabinet panel TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. ** llow 4" (10.2) min clearance to a wall for 90 door swing *115 oor swing oors can be adjusted to 90 door swing TOP VIW ** llow 4" (10.2) min clearance to a wall for 90 door swing 28 5/8" (72.7) ** These refrigerators are equipped with a 2-position door stop. The factory-set 115 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
FLUSH INST INSTLLTION 3/4" PNLS 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) epth to cleat 5 1/4" (13.3) 3/4" (1.9) Width of side cleats Finished cleats ase Trim 3/4" TOP VIW ase oor 51" (129.5) Flush inset width 49 1/2" (125.7) Width between cleats 1/2" (1.3) FLUSH INST INSTLLTION Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. 85" (215.9) Finished cleats 85" (215.9) 6" (15.2) 5" (12.7) 22 1/4" (56.5) 75" (190.5 ) From floor to bottom of electrical area WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. W SI VIW NTI-TIP RKT SOFFIT 3 1/2" 7" (17.8) WTR FRONT VIW 2" x 4" ut to 35" Length 7" (17.8) 3 1/2" etermine your installation construction and required anti-tip configuration: ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84". Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor Secure brackets to back wall of opening at 84" or your installation height from the floor. See Installation Instructions for detailed instructions. SI VIW INSTLL UNR SOFFIT SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X
FLUSH INST INSTLLTION 1/2" PNLS 5 3/8" (13.7) Finished cleats ase Trim TOP VIW ase FLUSH INST INSTLLTION 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 13/16" (52.9) epth to cleat Finished cleats 3/4" (1.9) Width of side cleats 85" (215.9) 1/2" 6" (15.2) oor 51" (129.5) Flush inset width 49 1/2" (125.7) Width between cleats 5" (12.7) 22 1/4" (56.5) 1/2" (1.3) 75" (190.5 ) From floor to bottom of electrical area Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. W SI VIW NTI-TIP RKT SOFFIT 3 1/2" 7" (17.8) WTR FRONT VIW 7" (17.8) 2" x 4" ut to 35" Length 3 1/2" etermine your installation construction and required anti-tip configuration: ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84". Wooden Wall Studs and No Soffit Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. See Installation Instructions for detailed instructions. SI VIW INSTLL UNR SOFFIT SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X
FLUSH INST 3/4" PNL IMNSIONS FLUSH INST INSTLLTION Freezer Grille Fresh Food PNL IMNSIONS 50" 11 3/16" 68 5/8" 20 7/8" 28 7/8" Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. 3/4" RIS OOR PNL ROUTING 11/32" 1/4" TIL TOP 3/4" 1/4" 7/16" NOT: Routed areas should be finished as they may be visible when assembled. Front TOP MXIMUM TOTL PNL WIGHT: Fresh food door panels 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs. OOR HNLS oor handle not included. custom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ack ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. 3/16" ack Front TIL OTTOM ORNR VIW SHOWING PITUR FRM ROUTING TIL HING SI ROUTR PTH 1/4" TIL HNL SI 2 1/16" 3/16" HING SI ack HNL SI 3/4" PNL OTTOM VIW (FTR ROUTING) OTTOM 3/4" PNL SI VIW (FTR ROUTING)
3/4" RIS GRILL PNL ROUTING NOT: Routed areas should be finished as they may be visible when assembled. TIL TOP TOP FLUSH INST INSTLLTION ack Front 2" ROUTR PTH 1/4" ack Front Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. ORNR VIW SHOWING PITUR FRM ROUTING Maximum total panel weight: Fresh food door panels 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs. 3/16" TIL OTTOM OTTOM 3/4" PNL SI VIW (FTR ROUTING) oor Handles oor handle not included. custom handle supplied by your cabinet maker may be used. TIL LFT SI ROUTR PTH 1/4" ROUTR PTH 1/4" 2 1/16" 2 1/16" TIL RIGHT SI ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. Front LFT SI RIGHT SI ack 3/4" PNL OTTOM VIW (FTR ROUTING)
FLUSH INST 1/2" PNL IMNSIONS Grille PNL IMNSIONS 1/4" acker 45 7/8" 9 1/2" 68 3/8" 18 9/16" 29 9/16".10" Space 45" 8 5/8" 67" 17 9/16" 25 9/16" 1/2" Overlay 50" 11 3/16" 68 5/8" 20 7/8" 28 7/8" FLUSH INST INSTLLTION The 1/2" overlay panel must be secured to a.10" spacer panel and a 1/4" thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Freezer Fresh Food Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel. 1/4" KR SSMLY ROUTING IMNSIONS Hinge Side Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs. oor 1/2" Overlay Freezer ack acker with Overlay ssembly Fresh Food ack 1/4" acker.10" Spacer PNL IMNSIONS Grille ack Fresh Food 2 1/16" 1/16" 1/8" 1/8" Freezer 2 1/16" 1/16" 1/8" 1/8" Grille 2 1/16" 2 1/16" 1 15/32" 7/32"
FTURS N NFITS L LIGHTING Light columns in the freezer and fresh food compartments extend the full length of the interior and L lighting located inside the vegetable and climate-control drawers illuminate contents without compromising space VN TMPRTUR MNGMNT SYSTM WITH MULTI-SHLF IR TOWR Provides even distribution of air throughout the refrigerator LIMT-ONTROL RWR llows you to express-chill beverages, expressthaw meats and select specific temperatures for perishable foods ISPNSR WITH PROXIMITY SNSOR esigned to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away IRY IN WITH NTR IVIR Has a unique magnetic seal that locks in freshness FILTR-HNG INITOR LIGHT Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser G WTR FILTR Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight R