LCD/Plasma Mount Manual
Product Overview: Thank you for your Cheetah Mount purchase. All Cheetah Mounts are designed to provide excellent function, high quality, easy installation and stylish appearance. The desk mount features a universal design that allows you to mount virtually any LED/LCD/Plasma display up to 55"* with hole patterns up to 28" horizontally by 19" vertically. The desk mount is designed to rotate up to 90 degrees and provides up to 15 degrees of downward tilt. The desk mount is constructed with 25 LBS of 100% High Grade Steel providing a sturdy and reliable mount. The TV bracket arms and separable wall plate allow for easy installation. Mounting hardware is included for your convenience. Thank you again and enjoy your mount. Key Features: Covers Hole Patterns 28" Horizontal by 19" Vertical Fits Up to VESA 600x400mm Fits Up to 55"* 1.5" Wide Continuous Mounting Holes Along Top And Bottom Of Desk Plate Rotates 90 Degrees 15 of Downward Tilt 25 LBS of High Grade Steel All Installation Hardware Included * Please be aware of the desk mount dimensions to insure your TV will fit. This mount will fit up to a 55" TV within the noted dimensions. Please see notes in the specifications section.
Parts List: Part # Quantity Description 1 1 Desk Mount Plate 2 1 Base Plate 3 1 Left Arm 4 1 Right Arm 5 1 Center Column 6 1 8mm Allen Wrench 7 1 4mm Allen Wrench 8 1 Wrench Tool 9 4 M5 15mm Bolt 10 4 M5 30mm Bolt 11 4 M6 30mm Bolt 12 4 M6 15mm Bolt 13 4 M8 30 mm Bolt 14 4 M8 15mm Bolt 15 4 25mm Square Shim 16 4 Spacer 17 4 8mm Lock Washer 18 4 6mm Lock Washer 19 4 5mm Lock Washer
Specifications: Model: Hole Pattern Coverage/ Supported VESA Patterns: Unit Weight: Shipping Dimensions: 3 Separate Packages APTMM 28" Horizontal by 19" Vertical or VESA 400x600mm Net: 25LBS Base: 24 1/4x13 1/2 x1 7/8" Plate: 31 3/8x9 7/8x 2 1/2" Column: 23 3/4x5 3/8x5" Unit Materials: Tilt Range: Wall Plate Screw Slots: Arm Bracket Dimensions: Arms, Wall Plate: 100% High Grade Steel 0-15 Downward 1.5" Wide by 0.5" Apart 20x1 13/16Wx1 5/8"D Wall Plate Dimensions: 30x9 7/16" Maximum Weight Limit: Used as Desk Stand: Used as Wall Mount: Cable Management: 80LBS 165LBS Two x 11.5x4.6" Openings Note: This mount will fit hole patterns supported my 90% of TV up to 60 But because this is a desk stand you will need to take in to consideration the height of your TV. With the Arms at the highest setting the TV Plate to the stand base is 13 1/16 from the bottom of the arm to the base is 1 11/16 So if you measure your TV and find that from the bottom mounting screw hole to the bottom of your TV is greater than the distance provided this may not work with your TV. As a general rule most TV s 32-50 will work with this stand but please check your TV before ordering.
Installation Instructions: Note: Please read all installation instructions carefully before installation. Section 1: 1. Desk mount column assembly: The center column will need to be attached to the base of the mount support. First, Remove the allen bolt and the washer located underneath the center column. Next, position the unit as shown to the right, then screw the allen bolt back on to the bottom of the center column. 2.Rotation lock: The desk mount utilizes a locking bolt to securely adjust the rotation of the unit up to 90 degrees. To install, insert 3 washers between the center column and base support. Insert the bolt through the bottom of the base support, between the washers and up to the center column. Install a washer and the rotation knob, then tighten down. 3.Mounting the TV Plate: To install the TV plate, Remove the bolts that came pre-assembled on the center support column. Hold the TV plate flat against the center column. Align the holes then insert the bolts and tighten down when you achieve the desired height.
Note on Locating hardware to mount arms to your display: If your display does not come with the mounting screws in the back of the display, check the factory desk stand as in some cases the same screws to hold the desk stand are used also to mount your display. If neither of these options work, the hardware pack included with your mount contains several of the most common sized screws for mounting your arm brackets to your display. 4.Installing arm brackets onto the back of your display: Once you locate the appropriate screws, attach the two arm brackets to the back of the display. To attach the arms use the proper bolt and lock washer for each of the four mounting holes. In the event your display has recessed holes or a curved back, your hardware pack includes plastic spacers to fill the gaps. These plastic spacers are not necessary for most installations. 5. Adjusting your tilt: To adjust the tilt position on your display you will need to loosen the knob on the side of each one of the arm brackets. Due to the narrow space between your display and the mounting plate, it is recommended to first adjust the tilt while you have the display face down on a soft surface such as a bed. Once the knobs are loosened adjust them to the desired position. After you have set the tilt position tighten the knobs on the arm brackets then proceed to Step 6. 6. Tightening the safety screws: Using a Philips head screw driver tighten the two bolts located at the bottom of the arm brackets. These screws prevent accidental liftoff of the wall plate. This will complete your installation of your mount. ATTENTION: This mount must be installed using the supplied hardware. Cheetah Mounts cannot be held liable for damage to Walls, TV's, Furniture, or Fixtures after installing this item. 2009 Cheetah Mounts Date: 8/10