2 2 2 0 22 2 0 Not to Scale Unless otherwise stated Brian Law's Wooden Clock rd Angle projection www.woodenclocks.co.uk Jan
0 2 2 2 2 2 2 2 2 2 2 2 2 2 22 ITEM NO. PART NUMBER DESCRIPTION QTY. back Wood 2 cross Wood Angled brace Wood front Wood squarespacer top Wood Pendulum hanger Wood Wall spacer Wood 2 squarespacer bottom Wood Front pin Wood 2 cover pin Wood 2 Securing pin Wood Dial spacer Wood 2 Clock dial Wood Shaft cover Wood Shaft cover Wood Pendulum head Wood Pendulum pivot Wood or Brass Pendulum rod Wood or Carbon Fibre Pendulum bob Wood Pendulum nut Wood or Brass 2 Shaft Brass 22 yoke Wood 2 escape Wood 2 Pallet2 Wood 2 Pallet Wood 2 Timing Wood 2 teeth Wood 2 Shaft0 Brass 2 2 Sleeve Wood or Perspex tube 2 Shaft Brass teeth_. Wood 2 Pawl Wood Sleeve0 Wood or Perspex tube teeth Wood 2 drum Wood 0teeth Wood 2 Ratchet Wood 0teeth Wood Pawl pin Wood 0 2teeth Wood teeth Wood 2 sleeve Wood or Perspex tube Weight To suit shaft Brass teeth Wood teeth Wood teeth_. Wood Key shaft Wood Minute hand Plastic Hour hand Plastic rope Cord.2mm 2 Not to Scale Unless otherwise stated Brian Law's Wooden Clock rd Angle projection www.woodenclocks.co.uk Nov
Sht of Shts A2 Not to Scale Unless otherwise stated Brian Law's Wooden Clock rd Angle projection www.woodenclocks.co.uk Nov
Note! Bottom of rod needs to be threaded M. You may need to splice in a section of Brass to the bottom of the rod to do this. Still keep the overall length the same. Brian Law's Wooden Clock UOS rd Angle projection www.woodenclocks.co.uk Nov
R2. 2. 2 Cut out mm deep 0.02.. Typical.0. 0.2 2.0.0..2 0..2.0 2 Back :2 Scale 22. Typical. 2 Front :2 Scale G 0. 22 G 2 Cross :2 Scale 2 Ø Drill on assembly Pendulum Hanger.0 SECTION G-G SCALE : 2 2 0 2 Brace Square Spacer Bottom 0 2 Wall Spacer X Securing Pin Cover Pin 2.0 R. Sq Front Pin X Shaft Cover R Shaft Cover 2 0 0 2 Square Spacer Top Brian Law's Wooden Clock UOS rd Angle projection www.woodenclocks.co.uk Nov
2 holes drilled from the back mm deep Pendulum Header Pendulum Bob 2. 0 Pendulum Rod Wood or Carbon Fibre 2 Thread M M 0 22 Dial Pendulum Pivot Pendulum Nut Dial Spacer Brian Law's Wooden Clock UOS rd Angle projection www.woodenclocks.co.uk Nov
R2.0. 2.0.0..0.02 R R.0 Gear teeth Gear teeth 2. R.0. 2.0 Gear teeth Gear teeth.0. L R Gear 0 teeth Gear 0 teeth J...0 2 Gear teeth. L 2. R.0. Gear teeth K R SECTION L-L SCALE :..0.0 Gear teeth R.0.0 SECTION J-J SCALE : `. Gear teeth K Gear 2 teeth SECTION K-K SCALE : All gears mm thick Profile of the gear faces where shown is optional Brian Law's Wooden Clock UOS J Gear 0 teeth rd Angle projection www.woodenclocks.co.uk Nov
. R 0.. M..2 22. 2. R 2 Pawl Pin R2.. 2. Ratchet 2 Pawl R. X 2 Timing Wheel M SECTION M-M 2 2. 2.0 With the pendulum hanging vertically Set up the Escapement and the pallets so that they are in the posiotions indicated by the drawing here. 2.0.2 2....... 2 Escapement 2 Pallet 2 Pallet 2 UOS Brian Law's Wooden Clock rd Angle projection www.woodenclocks.co.uk Nov
R... 2.Sq.. R. Drum. Key Shaft 22 Yoke Shaft Brass. 2 Sleeve Wood 2 Shaft Brass. 0 Sleeve 0 Wood 0 2 Shaft 0 Brass.. 2 Sleeve wood Shaft Brass ` Note! Sleeves may be made in multiples of shorter parts if it proves difficult to drill the long holes Brian Law's Wooden Clock Not to Scale Unless otherwise stated rd Angle projection www.woodenclocks.co.uk Nov