GHOST 400, GHOST 350, BUCK COMMANDER, PENETRATOR, QUAD 400, WILDCAT C5 & PANZER V CRANK COCKING DEVICE INSTRUCTION MANUAL CROSSBOW MODEL SHOWN IS OUR QUAD 400 BARNETT CROSSBOWS 955 LIVE OAK ST. TARPON SPRINGS, FL 34689
CRANK ASSEMBLY STEP 1 NOTE: ANCHORS WILL GO OVER STRING FROM SPOOLS TO CONTAIN THEM IN THE GROOVE. 2. right-side string spool 4. 1/4-20 socket-head cap screw 3. thumbscrew 6. crank handle assembly 5. 1/8 pins (4) 1. left-side string spool Insert 1/8 pins (5.) into right-side string spool (2.), then insert rightside string spool into middle stock hole. (Note: You may apply a white lithium grease into the spool bushing to reduce friction.) Insert left- side string spool (1.) into the middle stock hole. Important: Keep the string spools position the same way on both sides to allow even take-up of string during use (see note below). Once spools are connected, insert ¼-20 x 5/8 socket-head cap screw (4.) into right-side string spool (2.) and thread into left-side string spool (1.). To tighten, align crank handle (6.) with left-side string spool (1.) and thread in thumbscrew (3.). Using supplied Allen wrench, tighten ¼-20 x 5/8 socket-head cap screw (4.). NOTE: BE SURE THE STRING IS AT EQUAL LENGTHS ON BOTH THE RIGHT- AND LEFT-HAND SIDES OF THE SPOOL AND THAT THE KNOT HOLES ARE IN LINE WITH EACH OTHER ON BOTH SIDES BEFORE CONNECTING THEM TOGETHER (#1 & #2).
CRANK ASSEMBLY STEP 2 string string 7. right-side string anchor 9. finish cap (right side) 8. left-side string anchor 10. finish cap (left side) 11. #10-24 x 1 sockethead cap screw Insert right-side string anchor (7.) into front right stock hole. Insert left-side string anchor (8.) into front left stock hole. Insert #10-24 x 1 socket-head cap screw (11.) into left string anchor and tighten. Press right finish cap (9.) into right anchor hole and left finish cap (10.) into left anchor hole.
CRANK ASSEMBLY STEP 3 15. catch cover 14. socket-head cap screws 12. spool catch 13. catch plate Insert spool catch (12.) into the right-side back hole. Insert catch plate (13.) into left-side back hole. Insert #4-40 socket-head cap crews (14.) through catch plate and thread into spool catch. Press catch cover (15.) into hole when completed.
IMPORTANT QUAD 400 CRANK COCKING DEVICE string goes over string anchor BUCK COMMANDER, GHOST 350, GHOST 400, PENETRATOR, WILDCAT C5 and PANZER V CRANK COCKING DEVICE string goes under string anchor
Buck Commander, Ghost 400, Ghost 350, Penetrator, Wildcat C5 Hook Spindle Bracket Installation Instructions Materials (Shown in Figure 1): Qty: 1 CCD Hook Spindle Mount 1 2 Double-side adhesive pad (1 spare) 2 3 8-16 x 1 thread forming screw 1 4 #29 drill bit Not included 5 Phillips-head screwdriver Not included Not Pictured- Drill Not included Figure 1 Step 1. Step 2.
Step 3. (OPTIONAL) Step 4. (OPTIONAL) Step 5.
Quad 400 Hook Spindle Bracket Installation Instructions Materials (Shown in Figure 1): Qty: 1 Quad CCD Hook Spindle Mount 1 2 Double-side adhesive pad (1 spare) 2 3 8-16 x 1 thread forming screw 1 4 #29 drill bit Not included 5 Phillips-head screwdriver Not included Not Pictured- Drill Not included Figure 1 Step 1. Step 2.
Step 3. (OPTIONAL) Step 4. (OPTIONAL) Step 5.
WARNING: NEVER USE YOUR CRANK DEVICE TO UNCOCK / UNLOAD STRING FROM THE TRIGGER note: to disengage the ratchet feature, place toggle switch into the back and down position. this will allow crank handle to rotate in two directions. note: when cranking the string back, place the toggle switch in the forward position to activate the ratcheting feature. this will allow crank handle to rotate in one direction. With Crank Cocking Device (CCD) installed you are ready to use. 1. Place the Toggle Switch in the back and down position. 2. Attach String Puller Assembly to string by inserting crossbow string into hooks. 3. Install the Crank Handle to either right or left side (depending on your dominate hand) and tighten Thumbscrew. 4. Place Toggle Switch in the forward position to engage Right-Side String Spool and turn Crank Handle clockwise. Note: You should hear a ratcheting sound and the Crank Handle should not turn counterclockwise. 5. Turn the Crank Handle until the crossbow string engages the trigger and safety assembly. 6. While holding the Crank Handle securely, place the Toggle Switch into the back and down position. Turn Crank Handle slowly counterclockwise until the trigger assembly stops the crossbow string. 7. Place String Puller Assembly on the backside of scope mount or on the saddle bracket (see instructions pages 6-9).
SAFETY GUIDELINES DO NOT TURN HANDLE BACKWARDS WHILE COCKING THE BOW!! Doing this will damage the rope on the cranking device. The latch mechanism should always be engaged when cocking the crossbow. An audible clicking sound should be present while turning the handle in a forward rotation. If this clicking sound is not present, place the safety in the engaging position. UNCOCKING THE CROSSBOW: DO NOT UNCOCK THE CROSSBOW BY USING THE CRANK COCKING DEVICE. Doing so could cause bodily injury or damage your crossbow. The best way to unload your crossbow is to shoot an arrow into the ground. You may want to keep an old arrow with you for this purpose. DO NOT FIRE YOUR CROSSBOW WITH THE CRANK COCKING DEVICE HOOKS STILL FIXED ON THE STRING. Doing so may cause severe damage to your bow or cause personal injury. BARNETT OUTDOORS LIMITED WARRANTY The crank cocking device is guaranteed to the original purchaser to be free of manufacturer defects for a period of one year from the date of purchase. Our liability extends to parts, labor and return transportation to the customer. NOT COVERED: Ropes; transportation of defective product to our Service Department; damage caused by misuse, modification or failure to perform normal maintenance; any other expense, consequential damages, incidental damages or incidental damages, including damage to property or person. HOW TO OBTAIN SERVICE: DO NOT return the unit to the dealer that you purchased it from. Dealers are not authorized to make exchanges or returns on our behalf. Please contact our Sales Department to obtain a Return Authorization number (RA#) at 727-234-4999. Product returned without an RA# will be refused. Write the RA# on the outside of the package and attach to the product your name, address, telephone number and letter describing the problem. Carefully package and return, transportation prepaid, to: Barnett Outdoors, LLC Attn: Service Department 955 Live Oak St. Tarpon Springs, FL 34689
BARNETT OUTDOORS, LLC 955 LIVE OAK ST. TARPON SPRINGS, FL 34689 PHONE: 727-234-4999 FAX: 727-942-6100 Warranty Registration card (below) must be mailed within 10 days of the purchase to validate the warranty. WARRANTY CARD Name Age Address City State Zip Date of Purchase Phone # Place of Purchase Price Paid Purchase Address City State Zip