www.usdentaldepot.com - sales@usdentaldepot.com - 1 1-866-625-5558 - 1-954-874-6325 Accessories HANDLER - 103329 #16D Accela/Rotor Attachemnt #16D Accela/Rotor Attachemnt - 12000-24000RPM - Includes: Guards - Instructions - Light - High Speed Spindle - [H#16D] Turns your red wing lathe into a high speed alloy grinder - It attaches to the right side of the lathe - shipping info: 14x12x17in - Weight: 11lb US$ 975.10 HANDLER - 103332 #26SHLD Flex Shield 8x13in #26SHLD Flex Shield 8x13in [H# 26SHLD] Designed for adjustable protection - May be mounted on a lathe - table top or model trimmer - Adapting it to a base bolt or drilling a hole to accommodate the machine bolt mounting base will allow mounting to a sturdy surface - Shipping Weight 1lb US$ 48.10 HANDLER - 103355 #32SHLD Flex Shield 6x8in #32SHLD Flex Shield 6X8in attached to 13in adjustable arm [H# 32SHLD] Designed for adjustable protection - May be mounted on a lathe - table top or model trimmer - Adapting it to a base bolt or drilling a hole to accommodate the machine bolt mounting base will allow mounting to a sturdy surface - Shipping Weight 1lb US$ 48.70 FOREDOM - 101796 Dust Collector Hood Dust Collector Plastic Hood - each sold separatley - - 2 1/2in [64mm] Adapter that fits most collection system hoses - 6 1/2in [165mm] High - 4 5/8in [117mm] Wide - 8 5/8 [219mm] Deep - Hoods are made of heavy gauge sheet metal construction with non skid pads on the bottom - US$ 49.00 WELLS - 100640 Quick Chuck RightHand with Acc Quick Chuck RightHand with Acc [ embrague muneco ] [ VALOR compatible ] US$ 365.00 Chucks for lathes HANDLER - 101374 #16-0 Chuck Changer Only #16-0 Chuck Changer Only - provides full precision changing of 1/4in [.6cm ] and 3/32in [.2 cm ] diameter burs [H # 16 ] #16 is shipped with complete with chuck acessories as follows: p- 16-15 Arbor band chuck qty 1 - p-16-16 Spiral tapered chuck qty 1 - p-16-19 Stone chucks qty 1 - p-16-20 Mandrels for small abrassive wheels qty 2 - p-16-10 Clutch qty 1 - p-16-adw Adapter qty 1 - #16D for the right part motor - #16L for the left part motor - [ embrague spindle automatic ] US$ 308.70 1
Chucks for lathes HANDLER -101101 #67 Auto Chk #67-0 Auto Chuck - used with attachments - [H#67-0] - use w/ stone chuck- tapered chuck- bur chuck- arbor chuckautomatically changes chucks while lathe is in motion- HANDLER - 103480 #67A Auto chuck Kit #67A Auto chuck Kit - Auto-chuck [1] - Wrench [1] - Stone Chuck [1] - Tapered Chuck [1] - /32in [0.2cm] Bur Chuck [1] - Arbor Chuck [1] shipping 5x3-3/4x1in - weight 1lb US$ 61.25 US$ 88.15 HANDLER - 101103 Arbor Band Chk 1/4in #13-1 Arbor Band Chuck Right or Left - 1/4inch [ 0.6cm] - specifiy 13-1L (left) or 13-1 R(Right) when ordering- [H#13-1] - accommodates abrasive stones w/ 1/4 inch arbor only- manufactured of alloy steel and plated- US$ 9.90 HANDLER - 101097 Arbor Band Lft/Rgt 3/4 x 3/4in #9 Arbor Band- 3/4x 3/4inch [ 1.9 x 1.9cm] - specifiy 9L (left) or 9R (right) when ordering- [[H#9] - made of alloy steel and plated to fit onto standard dental tapered shafts- the abrasive band is held in place by tightening the end screw against the rubber arbor- US$ 17.05 KEYSTONE-034-1260020 Arbor Chk Ati-Achmt 3/4 Hd Arbor Chuck Ati-Achment For Jacobs 3/4 Head [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] US$ 12.00 KEYSTONE-034-1260030 Arbor Chk- Lft Hnd 1/4 sh Arbor Band Chuck - Left Hand - 1/4inch shank - For standard Lathe - 3/4 dia x 3/4in. wide abrasive bands - female section is designed for a standard 3/8in shaft [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] KEYSTONE-034-1260040 Arbor Chk- Rgt Hnd 1/4in sh Arbor Band Chuck- Right Hand - 1/4inch shank - For standard Lathe - 3/4 dia x 3/4in. wide abrasive bands - female section designed for standard 3/8in. shaft. [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] HANDLER - 101099 Atlas Precision Chk Rgt sh #18 Atlas Precision Chuck - Right Shaft -.001inch diameter [ 0.03mm] to.250inch [6.4mm]- [H#18] -This chuck is precise jacobs type chuck for use w/ chuck accessories having a diameter as specified above- it attaches to the right shaft of a dental lathe w/ standard dental tapered shafts - provides technician w/ unmatched concentricity- HANDLER - 101102 Auto Chk II Rgt 3/32in #67B Auto Chuck II - Right Side - designed to interchange 3/32inch [0.2cm] burs and mandrels- [H#67B] - Designed to change burs and mandrels while lathe is in motion- will provide precise bur changing while saving time- installs on the tapered shaft of dental lathes- KEYSTONE-034-1260050 Bur Chk- Rgt Hnd Bur Chuck - For standard Lathe Shaft - designed to be used w/ small burs & mandrels not exceeding 1/4 in. diam.- to be used w/ lathes having a tapered shaft - available for right hand side of the lathe only. ( Jacobs type ) [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental US$ 8.00 US$ 8.00 US$ 95.10 US$ 61.69 US$ 26.00 2
Chucks for lathes Porcelain Furnaces ] HANDLER - 101095 Jacobs Type JR. Chk-Rgt 1/2in # 8 Jacobs Type JR. Chuck - Right shaft motor - 1/2 inch - [1.3 cm] - [H#8] - The #8 chuck is designed for use on polishing motors which have 1.2 in [1.3cm] striaght shaft- all specifications are identical to 8T expect for its adaptation onto 1/2 in shaft- HANDLER - 101096 Jacobs Type JR. Chk-Rgt 1/4in # 8T Jacobs Type JR. Chuck - Right shaft motor -1/4 inch - [0.6 cm] - [H#8T] - Is designed specifically for use w/ small burs & mandrels which do not exceed 1/4 inch in diameter- it is built to be less expensive & semi- precise adjustable chuck for use on lathes w/ tapered shafts- opens w/ a CCW twist & closes w/ CW twist- HANDLER - 101087 Stone Chk -Lt Hnd 3/8in hole #2 Stone Chuck - Left Hand - 3/8inches [1cm] I.D.( hole size ) of the wheel- [H#2] - Stone chucks are designed to HANDLER - 101088 Stone Chk -Lt Hnd 5/16in hole #3 Stone Chuck - Right Hand - 5/16inches [0.8cm] I.D.( hole size ) of the wheel- [H#3] - Stone chucks are designed to HANDLER - 101090 Stone Chk -Rt Hnd 1/4in hole #5 Stone Chuck - Right Hand - 1/4inches [0.6cm] I.D.( hole size ) of the wheel- [H#5] - Stone chucks are designed to HANDLER - 101086 Stone Chk -Rt Hnd 3/8in hole #1 Stone Chuck - Right Hand - 3/8inches [1cm] I.D.( hole size ) of the wheel- - [H#1] - Stone chucks are designed to KEYSTONE-034-1260060 Stone Chk Attach 1/4in sh Stone Chuck Attachment - 1/4inch shank - For Jacobs 3/4 - [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] US$ 26.95 US$ 26.95 US$ 11.00 HANDLER - 101098 Stone Chk Lft/Rgt 1/4in #12 Stone Chuck 1/4inch [0.6cm] - Specifiy 12L (left) or 12R (Right) when ordering- [ H#12] - Designed w/ 1/4 shank for use in Jacobs type chucks- this stone chuck accommodates abrasive stones w/ 1/4 - I.D. only- manufactured of alloy steel and plated- US$ 11.00 KEYSTONE-034-1260070 Stone Chk- Lft Hand 1/4in sh Stone Chuck - Left Hand - 1/4inch arbor hole - 3/8inch shaft - for lathe and knock down wheels & stones -Made of steel. [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] HANDLER - 101089 Stone Chk- Lt Hnd 5/16in hole #4 Stone Chuck - Left Hand - 5/16inches [0.8cm] I.D.( hole size ) of the wheel-- [H#4] - Stone chucks are designed to US$ 9.00 3
Chucks for lathes KEYSTONE-034-1260080 Stone Chk- Rgt Hnd 1/4in hole Stone Chuck - Right Hand - 1/4inch arbor hole - 3.8inch shaft - for lathe and knock down wheels & stones - Made of steel. [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] HANDLER - 101091 Stone Chk-Lt Hnd 1/4in hole #6 Stone Chuck - Left Hand -1/4inches [0.6cm] I.D.( hole size ) of the wheel [H#6] - Stone chucks are designed to HANDLER - 101094-L Taper Brass Chk -Left Hnd #7BL Tapered Brass Chuck- - [H#7 BRASS LEFT] - #7B tapered chuck is designed excatly as the #7 steel chuck- execpt it is made of brass- These chucks provide easier on/off placement onto tapered dental shafts- causing less shaft wear- HANDLER - 101094 Taper Brass Chk -Right Hnd #7BR Tapered Brass Chuck- - [H#7 BRASS RIGHT] - #7B tapered chuck is designed excatly as the #7 steel chuckexecpt it is made of brass- These chucks provide easier on/off placement onto tapered dental shafts- causing less shaft wear- KEYSTONE-034-1790070 Taper Spindle - Rgt Hnd 3/8in Tapered Spindle - Right Hand 3/8inch shaft - standard tapered - made of steel - designed to be used with buffing wheels - brushed - and centered - [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] KEYSTONE-034-1790060 Taper Spindle -Lft Hnd 3/8in Tapered Spindle - Left Hand - 3/8inch shaft - standard tapered - made of steel - designed to be used with buffing wheels - brushed - and centered wheels - [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] KEYSTONE-034-1790010 Taper Spindle Chk1-1/2x 4in Tapered Spindle Chuck - 1-1/2x 4inch - Ai-I-Atachment For Jacobs [ Keystone Abrasives - Keystone Dental Tools ][ Us Dental Depot is specialized business in Dental lab equipment & Dental Porcelain Furnaces ] US$ 9.00 US$ 8.50 US$ 8.50 US$ 8.50 HANDLER - 101092-1 Taper Steel Chk - Lft Hnd #7 Tapered Steel Chuck- 7L (Left) - [H#7 STEEL] - #7 tapered chuck is designed specifically for use with buffing wheels- brushes- and lead centered wheels- Precision manufactured of alloy steel- this chuck is built for placement onto lathes and polishing motors containing standard tapered shafts- HANDLER - 101092 Taper Steel Chk - Rgt Hnd #7 Tapered Steel Chuck- 7R (Right) - [H#7 STEEL] - #7 tapered chuck is designed specifically for use with buffing wheels- brushes- and lead centered wheels- Precision manufactured of alloy steel- this chuck is built for placement onto lathes and polishing motors containing standard tapered shafts- HANDLER - 101100 Tapered Chk 1/2in or 5/8in #20 Tapered Chuck Right or Left Side - 1/2inch [13mm] or 5/8inch [16mm] - [H#20] Especify with the oprder please - Manufactured of steel alloy- provides the user with a heavy duty chuck for use w/ buffs- brushes- and lead accessories- US$ 11.00 4
Complete lathes Complete lathes HANDLER- 103325 #16 Chuck/Chnger w/accessories #16 Chuck/Changer with Accessories - Arbor Band Chuck [1] - Spiral Tapered Chuck [1] - Stone Chucks [2] - Mandrels for small abrasive wheels [2] - Collect Wrench [1] - Clutch [1] - ADW Adapter [1] - Designed to provide full automatic precision changing of 1/4in and 3/32in diameter burs - mandrels - and chuck accessories with the slight movement of a handle while the motoe is turning - It provides the technician with excat concentricity and quick easy changing of variuos chucks which speeds up grinding - polishing- and finishing procedures - It is adaptable to most dental motors - Dimensions: 8-3/4x4x6-1/4in Shipping Weight: 5lbs [ redwing ] US$ 328.30 HANDLER- 103326 #16B-1 Chuck/Chnger #16B-1 Chuck/Changer with Lathe - Factory installed on the right side of a 26 HIGH BASE - 1/4 HP - 1725-3450RPM - Motor Handler con embrague o chuck automatico ya instalado - [ redwin ] US$ 595.56 HANDLER -103327 #16C Accela/Rotor High Base #16C Accela/Rotor High Base - 12000/24000 RPM - Complete Red Wing Lathe - Accela/Rotor with removable light and protective sheild - High Speed Spindle - Adjusting levers and necessary guards - Dimensions - 19x19x11in -Weight -50lb - [H#16C] This product is a combination of the Accela/Rotor attachment and #26A Red Wing Lathe - It converts the right side of the lathe from standard lathe speeds for use in finnishing non precious alloys and chrome cobalts alloys - The high speed spindle incorporates an avtivating handle which opens and closes the [3/21in] collects for ease of changing burs and mandrels while the motor is running US$ 1,160.00 HANDLER - 103328 #16C Accela/Rotor Low Base #16C Accela/Rotor Low Base - 12000/24000 RPM - Complete Red Wing Lathe - Accela/Rotor with removable light and protective sheild - High Speed Spindle - Adjusting levers and necessary guards - Dimensions - 19x19x11in -Weight -50lb - [H#16C] This product is a combination of the Accela/Rotor attachment and #26A Red Wing Lathe - It converts the right side of the lathe from standard lathe speeds for use in finnishing non precious alloys and chrome cobalts alloys - The high speed spindle incorporates an avtivating handle which opens and closes the [3/21in] collects for ease of changing burs and mandrels while the motor is running US$ 1,225.00 HANDLER- 100626 16B Chuck/Chnger w/lathe 1/4Hp HANDLER 16B CHUCK/CHANGER W/ LATHE 1/4HP *#16B Chuck changer with Lathe *Factory installed on the Right Side of a 25A Low Base *1/4HP *1725-3450RPM US$ 519.99 HANDLER - 101106 26 Rd Wg 1/4 Hp - 2 Spd -Hi Sh #26 Red Wing Lathe- 1/4 HP- 2 Speed- 1725/3450 Rmp- High shaft 8- Chuck removers- [H#26] - use as a polishing lathe- its tapered shafts will accpet standard dental tapered chucks- 6 in shaft height allows larger diameter buffing wheels for pumice & dry polishing operations- may be supplied w/ 1/2 in straight shafts when specified- US$ 280.00 5
Complete lathes HANDLER - 101105 26A Rd Wg 1/4Hp - Lw Sh 26A Red Wing LatheA full 1/4 HP *1725/3450 rpm * lathe for use on top of laboratory bench (115 Volts/60Hz). * Its 4 1/2 [11.4cm] shaft height *Allows for easy use by the technician with hands resting on the tabletop. Shipped with *Standard dental tapered shafts *Each lathe includes a right and left chuck remover *Which provides ease of removal of standard dental chucks *Manufactured to provide years of durable service while being utilized for such operations as polishing and grinding. *This unit may be supplied with 1/2 [1.3cm] straight shafts when specified *Available in 115 Volts/50Hz, 220/50Hz and 220/60Hz at additional charge *NOTE: Specify No. 26AS for motor with 1/2 [1.3cm] straight shafts Technical specifications: *Shipping Wgt.: 39 lbs [17.7 Kg] *Unit Dimensions: 15 1/2 long x 7 7/8 wide x 7 1/4 high [39cm x 20cm x 18cm] *Model: 26A US$ 238.00 HANDLER - 101107 27 Rd Wg 1/4 Hp - 1 Spd -Hi Sh #27 Red Wing Lathe - 1/4 HP- 1 Speed- 3450 Rpm- High 8 shaft- [H#27] - for technician that desires a single speed polishing motor where a 3450 rpm speed is used exclusivley for polishing- may be supplied with 1/2in shafts when specified- HANDLER - 101109 28H Rd Wg 1/3Hp - 2 Spd- Hi Sh 28H Red Wing LatheA 1/3 HP *Two speed 1725/3450 rpm *High base polishing motor with 6 shaft height *Built to accommodate larger diameter buffs and chuck accessories *Provides added torque for the frequent polisher US$ 259.56 US$ 297.78 *The unit is shipped with *standard dental tapered shafts with chuck removers *Available in 115 Volts/60Hz and 115 Volts/50Hz, 220 Volts/50Hz and 220 Volts/60Hz *at additional charge *NOTE: Specify No. 28HS for motor with 1/2 [1.3cm] straight shafts Technical Specifications: *Shipping Wgt.: 42 lbs [19.5 Kg] *Unit Dimensions.: 15 3/4 wide x 7 7/8 deep x 8 3/4 high [40cm x 20cm x 22.2cm] *Model: 28H HANDLER - 101108 28L Rd Wg 1/3Hp - 2 Spd -Lw Sh #28L Red Wing Lathe- 1/3 HP- 2 Speed- 1725/3450 Rmp- Low shaft 8 [4.5 inch] - [H#28L] - for technician who requires additional torque - contains standard dental tapered shafts w/ chuck removers- HANDLER -101110 29 Rd Wg Mtr -1 Spd 6-3/8in Sh #29 Red Wing Motor- 1/2HP- 1 Speed- 2450Rmp - 6-3/8inch shaft- [H#29] - for heavy use by technician and polisher- rugged polishing motor will provide years of trouble free service-shipped with #20 tapered chucks (left & right) HANDLER - 101111 29A Rd Wg Mtr 1/2Hp-1 Spd Hi S #29A Red Wing Motor- 1/2 HP- 1 Speed - 3450 Rmp- high shaft 6inches- [H#29A] - Extra heavy duty use by techinican - requires extra torque- manufactured w/ 1/2 inch straight shafts- #20 tapered chucks for use w/ large buffs- US$ 297.78 US$ 301.56 US$ 309.96 6
Complete lathes brushes- and similar chucks- FOREDOM - 101795 Bch Mini Lth w/ Sp 1/6Hp 220v Bench Mini Lathe with Tapered Spindes - 220V only -1/6HP High Torque Motor - 125Watts - Continuous Rating - 5/16in Diameter motor shaft - 500-7000RPM - Weight 7.5lbs [3.4kg] - Width 13in [330mm] between spindles - Height 5 1/8in [130mm] - Height of spindle center from table surface 3 3/4in [95mm] - ball bearing - Lathe comes with the A-TM5 [left hand] - and A-TM6 [right hand] tapered spindles for holding buffs and brushes up to 4inches [100mm] - Dust collector hoods sold separatley - US$ 172.00 ECCO - 101476 Lathe polisher 1/3 Hp 110vo Lathe polisher 1/3 Hp 110voltz - US$ 175.00 7
Catalog Index / Indice del Catálogo Accessories 1 Chucks for lathes 1 Complete lathes 5 8