DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003
Product specification 2 SCOPE This specification describes series chip resistors with lead-free terminations made by thick film process. APPLICATIONS All general purpose application FEATURES Halogen Free Epoxy RoHS compliant - Products with lead free terminations meet RoHS requirements - Pb-glass contained in electrodes, resistor element and glass are exempted by RoHS Reducing environmentally hazardous wastes High component and equipment reliability Saving of PCB space None forbidden-materials used in products/production ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC Both part numbers are identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. YAGEO BRAND ordering code GLOBAL PART NUMBER (PREFERRED) (1) TOLERANCE X R - XX XXXX L (1) (2) (3) (4) (5) (6) F = ±1% J = ±5% (for Jumper ordering, use code of J) (2) PACKAGING TYPE R = Paper / PE taping reel (3) TEMPERATURE COEFFICIENT OF RESISTANCE = Base on spec (4) TAPING REEL 07 = 7 inch dia. Reel 7D = 7 inch dia. Reel, 2 x Standard Quantity 10 = 10 inch dia. Reel 13 = 13 inch dia. Reel (5) RESISTANCE VALUE There are 2~4 digits indicated the resistance value. Letter R/K/M is decimal point, no need to mention the last zero after R/K/M, e.g.1k2, not 1K20. Detailed resistance rules show in table of Resistance rule of global part number. (6) DEFAULT CODE Letter L is system default code for ordering only (Note) Resistance rule of global part number Resistance code rule Example D1 0R XRXX (1 to.76 Ω) XXRX (10 to 7.6 Ω) XXXR (100 to 76 Ω) XKXX (1 to.76 KΩ) XMXX (1 to.76 MΩ) D1 = Dummy 0R = Jumper 1R = 1 Ω 1R5 = 1.5 Ω R76 =.76 Ω 10R = 10 Ω 7R6 = 7.6 Ω 100R = 100 Ω 1K = 1,000 Ω K76 = 760 Ω 1M = 1,000,000 Ω M76=,760,000 Ω ORDERING EXAMPLE The ordering code of a chip resistor, value 56 X with ±1% tolerance, supplied in 7-inch tape of 20,000 units per reel is: FR-7D56RL. NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label, "LFP" or specific symbol can be printed
Product specification 3 PHYCOMP BRAND ordering codes Both GLOBAL PART NUMBER (preferred) and 12NC (traditional) codes are acceptable to order Phycomp brand products. GLOBAL PART NUMBER (PREFERRED) For detailed information of GLOBAL PART NUMBER and ordering example, please refer to page 2. 12NC CODE TYPE/ 0402 2322 XXX XXXXX L (1) (2) (3) (4) START IN (1) TOL. (%) (1) The resistors have a 12-digit ordering code starting with 2322. (2) The subsequent 4 or 5 digits indicate the resistor tolerance and packaging. (3) The remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of Last digit of 12NC. (4) Letter L is system default code for order only (Note) ORDERING EXAMPLE RESISTANCE PAPER / PE TAPE ON REEL (units) (2) RANGE 10,000 20,000/not preferred 50,000 RC31 2322 ±5% 1 to 22 MΩ 705 70xxx --- 705 87xxx RC32 2322 ±1% 1 to 10 MΩ 706 7xxxx --- 706 8xxxx Jumper 2322-0 Ω 705 1001 --- 705 1007 The ordering code of a RC32 resistor, value 56 X with ±1% tolerance, supplied in tape of 10,000 units per reel is: 23227067560L or FR-0756RL. Last digit of 12NC Resistance decade (3) Last digit 0.01 to 0.076 X 0 0.1 to 0.76 X 7 1 to.76 X 8 10 to 7.6 X 100 to 76 X 1 1 to.76 KX 2 10 to 7.6 KX 3 100 to 76 KX 4 1 to.76 MX 5 10 to 7.6 MX 6 Example: 0.02 X = 0200 or 200 0.3 X = 3007 or 307 1 X = 1008 or 108 33 KX = 3303 or 333 10 MX = 1006 or 106 NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label, "LFP" or specific symbol can be printed
ynsc007 Chip Resistor Surface Mount Product specification 4 MARKING Fig. 1 No marking For further marking information, please see special data sheet Chip resistors marking CONSTRUCTION The resistor is constructed on top of a high-grade ceramic body. Internal metal electrodes are added on each end to make the contacts to the thick film resistive element. The composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environment influences. The resistor is laser trimmed to the rated resistance value. The resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on Nibarrier) are added. See fig.2 OUTLINES For dimension see Table 1 H I 2 I 1 W overcoat protective glass resistive layer (Jumper chip is a conductor) inner electrode termination(ni/matte tin) inner electrode ceramic substrate overcoat DIMENSIONS L YNSC056 Table 1 TYPE L (mm) 1.00 ±0.05 W (mm) 0.50 ±0.05 H (mm) 0.35 ±0.05 I 1 (mm) 0.20 ±0.10 I 2 (mm) 0.25 ±0.10 Fig. 2 Chip resistor outlines
Product specification 5 ELECTRICAL CHARACTERISTICS Table 2 CHARACTERISTICS 1/16 W Operating Temperature Range 55 C to +155 C Maximum Working Voltage 50 V Maximum Overload Voltage 100 V Dielectric Withstanding Voltage 100 V 5% (E24) 1 Ω to 22 MΩ Resistance Range 1% (E24/E6) 1 Ω to 10 MΩ Zero Ohm Jumper < 0.05 Ω 1 Ω R 10 Ω ±200 ppm/ C Temperature Coefficient 10 Ω < R 10 MΩ ±100 ppm/ C 10 MΩ < R 22 MΩ ±200 ppm/ C Jumper Criteria Rated Current 1.0 A Maximum Current 2.0 A FOOTPRINT AND SOLDERING PROFILES For recommended footprint and soldering profiles, please see the special data sheet Chip resistors mounting. PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PRODUCT TYPE PACKING STYLE REEL DIMENSION QUANTITY PER REEL Paper / PE Taping Reel (R) 7" (178 mm) 10,000/20,000 units 10" (254 mm) 20,000 units 13" (330 mm) 50,000 units NOTE 1. For paper/pe tape and reel specification/dimensions, please see the special data sheet Chip resistors packing 2. For size of 0402, standard quantity is 10,000 units per reel FUNCTIONAL DESCRIPTION POWER RATING rated power at 70 C is 1/16 W RATED VOLTAGE The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V= (P X R) or max. working voltage whichever is less Where V=Continuous rated DC or AC (rms) working voltage (V) P=Rated power (W) R=Resistance value (X) handbook, halfpage P (%P rated) 100 50 0 55 0 50 70 100 MLB206_2 155 o T amb ( C) Fig. 3 Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (T amb )
Product specification 6 TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Coefficient of Resistance (T.C.R.) IEC 60115-1 4.8 At +25/ 55 C and +25/+125 C Formula: R 2 R 1 T.C.R= ------------------------- 10 6 (ppm/ C) R 1 (t 2 t 1 ) Where t 1 =+25 C or specified room temperature t 2 = 55 C or +125 C test temperature R 1 =resistance at reference temperature in ohms R 2 =resistance at test temperature in ohms Refer to table 2 Life/Endurance IEC 60115-1 4.25.1 At 70±5 C for 1,000 hours, RCWV applied for 1.5 hours on, 0.5 hour off, still air required ±(1.0%+0.05 Ω) for 1% tol. ±(3.0%+0.05 Ω) for 5% tol. <100 mω for Jumper High Temperature Exposure/ Endurance at Upper Category Temperature IEC 60068-2-2 1,000 hours at 155±5 C, unpowered ±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. Moisture Resistance MIL-STD-202G Method-106G Each temperature / humidity cycle is defined at 8 hours, 3 cycles / 24 hours for 10d. with 25 C / 65 C 5% R.H, without steps 7a & 7b, unpowered Parts mounted on test-boards, without condensation on parts Measurement at 24±2 hours after test conclusion ±(0.5%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. <100 mω for Jumper Thermal Shock MIL-STD-202G Method-107G -55/+125 C Number of cycles required is 300. Devices unmounted Maximum transfer time is 20 seconds. Dwell time is 15 minutes. Air Air ±(0.5%+0.05 Ω) for 1% tol. ±(1%+0.05 Ω) for 5% tol. Short Time Overload IEC60115-1 4.13 2.5 times of rated voltage or maximum overload voltage whichever is less for 5 sec at room temperature ±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol.
Product specification 7 TEST TEST METHOD PROCEDURE REQUIREMENTS Board Flex/ Bending IEC 60068-2-21 Chips mounted on a 0mm glass epoxy resin PCB (FR4) 5 mm bending Bending time: 60±5 seconds ±(1.0%+0.05 Ω) for 1%, 5% tol. Low Temperature Operation IEC 60068-2-1 The resistor shall be subjected to a DC rated voltage for 1.5 h-on, 0.5 h-off, at -55±3 C This constitutes shall be repeated for 6 hours However the applied voltage shall not exceed the maximum operating voltage ±(0.5%+0.05 Ω) for 1% tol. ±(1.0%+0.05 Ω) for 5% tol. Insulation Resistance IEC 60115-1 4.6 Rated continuous overload voltage (RCOV) for 1 minute 10 GΩ Type Voltage (DC) 100 V Dielectric Withstand Voltage IEC 60115-1 4.7 Maximum voltage (V rms ) applied for 1 minute Type Voltage (AC) 100 V rms No breakdown or flashover Resistance to Solvent IPC/JEDEC J-STD-020D lsopropylalcohol (C 3 H 7 OH) followed by brushing No smeared Noise IEC 60115-1 4.12 Maximum voltage (Vrms) applied Resistors range Value R < 100 Ω 10 db 100 Ω R < 1 KΩ 20 db 1 KΩ R < 10 KΩ 30 db 10 KΩ R < 100 KΩ 40 db 100 KΩ R < 1 MΩ 46 db 1 MΩ R 22 MΩ 48 db Humidity IEC 60115-1 4.21 Steady state for 1000 hours at 40 C / 5% R.H. RCWV applied for 1.5 hours on and 0.5 hour off ±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. <100 mω for Jumper
Product specification 8 TEST TEST METHOD PROCEDURE REQUIREMENTS Intermittent IEC 60115-1 4.3 2.5 times of rated voltage or maximum ±(1.0%+0.05 Ω) for 1% tol. Overload overload voltage whichever is less for 1 second ±(2.0%+0.05 Ω) for 5% tol. on and 25 seconds off; total 10,000 cycles <100 mω for Jumper Solderability - Wetting IPC/JEDEC J-STD-002B test B Electrical Test not required Magnification 50X SMD conditions: 1 st step: method B, aging 4 hours at 155 C dry heat 2 nd step: lead-free solder bath at 245±3 C Dipping time: 3±0.5 seconds Well tinned ( 5% covered) - Leaching IPC/JEDEC J-STD-002B test D Lead-free solder, 260 C, 30 seconds immersion time - Resistance to Soldering Heat IEC 60068-2-58 Condition B, no pre-heat of samples Lead-free solder, 260 C, 10 seconds immersion time Procedure 2 for SMD: devices fluxed and cleaned with isopropanol ±(0.5%+0.05 Ω) for 1% tol. ±(1.0%+0.05 Ω) for 5% tol.
Product specification REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 6 Jan 05, 2011 - - Typo updated Version 5 Apr 27, 2010 - - Updated test items and methods - Add new taping reel code of 7 inch dia. reel with double standard quantity (20,000 units per reel) Version 4 Jul 21, 200 - - Test items and methods updated - Test requirements upgraded Version 3 Jul 15, 2008 - - Change to dual brand datasheet that describe with RoHS compliant - Description of "Halogen Free Epoxy" added - Define global part number Version 2 Sep 03, 2004 - - New datasheet for 0402 thick film 1% and 5% with lead-free terminations - Replace the 0402 part of pdf files: RC01_11_21_31_5, RC02_12_22_32_10 - Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any product change will be announced by PCN.