Fasteners & Accessories For Commercial Construction

Fasteners & Accessories For Commercial Construction

Table of Contents Page Structural Performance... 1-2 Fastener Strength and Pullout Values... 2 Carbon Steel Self-Drill Fasteners, No Washer... 3 Structural Steel Self-Drill Fasteners... 4 Carbon Steel Self-Drill Fasteners, bondseal Washer... 5 Cupped Sealer Self-Drill Fastners, EPDM Washer... 6 410 Stainless Steel Self-Drill Fasteners... 6 ZAC Zinc Aluminum Capped Self-Drill Fasteners... 7 MAC Stainless Capped Self-Drill Fasteners... 7 Flex5 Grade 5 Performance Fasteners... 8 Wood to Metal Self-Drill Fasteners... 9 woodgrip Fasteners... 10 woodgrip HiLo Fasteners... 10 #14 Milled Point Wood Screw...11 evergrip Bi-Metal 300 Series Stainless Fasteners...11 woodgrip 300 Series Stainless Aluminum Panel Fasteners...11 woodmac Wood Screw... 12 woodzac HiLo Zinc Aluminum Capped Fastener... 12 Clip Fasteners... 13 Page Carbon Steel Self-Tapping Type A Fasteners... 14 304 Stainless Steel Self-Tapping Type A Fasteners... 14 Carbon Steel Self-Tapping Type B Fasteners... 15 304 Stainless Steel Self-Tapping Type B Fasteners... 15 SX - HWH 304SS Bi-Metal Self-Drill Fasteners... 16 irius SX 304SS Bi-Metal Self-Drill Fasteners... 17 SX TORX 304SS Bi-Metal Self-Drill Fasteners... 18 Blind Rivets... 18 BULB-TITE Rivets... 19-20 Blind Rivet Tools... 20 Grommet Fasteners... 20 Pipe Flashing... 21 Hannoband BG1 Joint Sealant Tape... 22 vistacoat Premium System... 22 #12 Dekfast Phillips Head (insulation attachment)... 23 #14 Dekfast Phillips Head (insulation attachment)... 24 Insulation Stress Plates... 24 Zinc Nailins... 25 Structural Performance Fastener Sizes Fastener Size #8 #9 #10 #12 1/4 #14 #17 Thread Diameter Decimal Equivalent.165.181.190.216.243.250.291 Steel Gauge Sizes* Gauge 30 29 28 26 24 22 20 18 16 14 12 1/8 10 3/16 1/4 1/2 Decimal Equivalent (in.).012.014.015.018.024.030.036.048.060.075.105.125.134.187.250.500 Decimal Equivalent (mm).30.36.38.46.61.76.91 1.22 1.52 1.91 2.67 3.18 3.40 4.75 6.35 12.70 *Standard steel thickness used for panels, purlins and girts. Fasteners are designed to withstand a varied range of types of loading. Each panel or structural system has its own specifi c fastener loading requirements. Care must be taken to ensure that the appropriate loading requirements for each application are considered. Utlimate Shear Strength The point at which a fastener fails under a load exerted in offset opposing directions, usually upon the shank of the fastener. Typical structural performance criteria that infl uence fastener design include: Ultimate Tension Strength The point at which a fastener fails under a load exerted in two direct opposite direction Ultimate Pull-out Performance The ability of a fastener s threaded connection to remain intact and resist tensile loads. Ultimate Torsion Strength The point at which a fastener fails under a twisting load exerted on the head during installation in a torsional direction. Self-tapping fasteners require that a pilot hole be drilled prior to installation. The pull-out resistance will be directly related to the pilot hole diameter. Self-drilling fasteners have been developed, and are available, for most steel contruction applications, to a metal thickness of 1/2. This type of fastener is manufactured with its own integral drill point, which is engineered to drill the optimum hole size to facilitate effi cient thread forming in the metal structure, resulting in optimized pullout values. www.sfsintecusa.com 1

Structural Performance, continued Ultimate Pull-over performance The ability of a fastener to resist the pulling of the fastened sheet material over the head of the fastener due to gravity, wind, or other load. SFS intec is proud to be a member of these industry trade associations: The resistance to pull-over failure is related to the strength and diameter of the fastener washer and the strength and thickness of the metal panel. Fastener Strength & Pullout Values Strength Values Diameter and TPI Tensile lbs. Min. Shear Avg. lbs. Ultimate Torque Min. in-lbs. 8-18 1575 1035 42 10-16 1825 1535 61 10-24 2548 1621 65 12-14 2900 2050 92 12-24 3450 2420 100 1/4-14 3800 2850 150 1/4-20 4200 2920 156 Pullout Values (Average lbs. ultimate) Diameter and TPI Point Size Gauge 26 24 22 20 18 16 14 12 1/8 3/16 1/4 8-18 2 -- -- -- 292 479 685 933 -- -- -- -- 10-16 3 -- -- -- 293 487 690 941 1432 2017 -- -- 10-24 3 -- -- -- 335 496 702 901 1469 2112 2668 -- 12-14 3 -- -- -- 273 535 665 901 1524 2780 2900* -- 12-24 4 -- -- -- -- -- -- 1075 1378 1802 3450 3450 12-24 4.5 -- -- -- -- -- -- 1075 1378 1802 3450 3450 12-24 5 -- -- -- -- -- -- 1075 1378 1802 3450 3450 1/4-14 1 204 304 379 -- -- -- -- -- -- -- -- 1/4-14 3 -- -- -- -- 483 687 1151 1697 2634 3771 -- 1/4-20 5 -- -- -- -- -- -- -- 1532 2200 3163 4200 *Denotes tensile failure Disclosure Statement Fastener data shown herein is subject to change or correction for typographical error without notice. All test data and ultimate values shown in the catalog are the result of laboratory testing. Specifi c job conditions should be considered and appropriate safety factors applied when specifying fasteners. In actual applications, proper installation techniques must be used to assure adequate performance of the fastener. Final selection of fasteners or accessories for use is ultimately the decision of the purchaser. While SFS intec, Inc. may assist by providing data and information for comparison, SFS intec makes no suggestions or warranties pertaining to the suitability of its products for any particular application. TORX is a registered trademark of Textron Inc. Hannoband is a registered trademark of Hanno Werk GmbH & Co. KG. 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 2

Carbon Steel Self-Drill Fasteners Metal to metal applications Buy American Act 1 10-16 SD3 12-14 SD3 1/4-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 1/4 AF, No Washer 793029 8-18 x 1/2 SD2.035-.100.205 10000 36.0 793080 8-18 x 5/8 SD2.035-.100.330 10000 40.0 793138 8-18 x 3/4 SD2.035-.100.455 5000 25.0 Impax HWH 5/16 AF, No Washer 793249 10-16 x 5/8 SD2.035-.110.187 7500 45.0 1473272 10-16 x 3/4 w/serration SD2.035-.150.312 5000 35.0 793362 10-16 x 3/4 SD3.035-.150.312 5000 30.0 1484397 10-16 x 3/4 SD3.035-.150.312 5000* 30.0 793413 10-16 x 1 SD3.035-.150.562 5000 40.0 793469 10-16 x 1-1/4 SD3.035-.150.812 3500 31.5 793496 10-16 x 1-1/2 SD3.035-.150 1.062 3500 35.0 Impax HWH 5/16 AF, No Washer 783060 12-14 x 3/4 SD3.035-.210.250 5000 40.0 794234 12-14 x 1 SD3.035-.210.375 2500 25.0 795053 12-14 x 1-1/4 SD3.035-.210.625 2500 30.0 796234 12-14 x 1-1/2 SD3.035-.210.875 2500 32.5 796909 12-14 x 2 SD3.035-.210 1.375 2000 34.0 797000 12-14 x 2-1/2 SD3.035-.210 1.875 2000 42.0 797067 12-14 x 3 SD3.035-.210 2.375 1000 25.0 1299624 12-14 x 4 SD3.035-.210 3.375 1000 30.0 797805 1/4-14 x 7/8 (lap) SD1.030-.095.335 2500 35.0 Impax HWH 3/8 AF, No Washer 797166 1/4-14 x 3/4 SD3.050-.210.182 2500 32.5 798553 1/4-14 x 1 SD3.050-.210.432 2500 32.5 798810 1/4-14 x 1-1/4 SD3.050-.210.682 2000 36.0 798973 1/4-14 x 1-1/2 SD3.050-.210.932 2000 40.0 799086 1/4-14 x 2 SD3.050-.210 1.432 1500 40.5 1300360 1/4-14 x 2-1/2 SD3.050-.210 1.932 1000 33.0 799115 1/4-14 x 3 SD3.050-.210 2.432 750 27.0 1300369 1/4-14 x 4 SD3.050-.210 3.432 1000 42.0 Indicates domestic Indicates E-Zinc plating 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 3

Structural Steel Self-Drill Fasteners Metal to metal applications Buy American Act 1 Painted 12-24 SD5 1/4-20 SD5 Silver Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, No Washer 783082 12-24 x 7/8 SD4.075-.250.300 2500 25.5 795664 12-24 x 1-1/4 SD4.5.075-.375.462 2500 32.5 795839 12-24 x 1-1/4 SD5.075-.500.520 2500 32.5 796618 12-24 x 1-1/2 SD5.075-.500.770 2500 32.5 783126 12-24 x 2 SD5.075-.500 1.270 2000 38.0 Impax HWH 3/8 AF, No Washer 1356393 1/4-20 x 3 SD5.105-.500 0-2.143 1500* 52.5 1356395 1/4-20 x 4 SD5.105-.500.432-3.143 1000* 46.0 1356396 1/4-20 x 5 SD5.105-.500 1.432-4.143 600* 29.9 1356398 1/4-20 x 6 SD5.105-.500 2.432-5.143 500* 33.5 1356399 1/4-20 x 7 SD5.105-.500 3.432-6.143 500* 38.5 1356400 1/4-20 x 8 SD5.105-.500 4.432-7.143 500* 43.5 Buy American Act 1 12-24 SD5 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal Washer 783065 12-24 x 7/8 SD4.075-.250.200 2500 32.5 795491 12-24 x 1-1/4 SD4.5.075-.375.362 2500 42.5 795718 12-24 x 1-1/4 SD5.075-.500.420 2500 40.0 796507 12-24 x 1-1/2 SD5.075-.500.670 2000 42.5 783097 12-24 x 2 SD5.075-.500 1.170 2000 44.0 Impax HWH 3/8 AF, with bondseal Washer 1356420 1/4-20 x 3 SD5.105-.500 0-2.043 1500* 57.0 1356421 1/4-20 x 4 SD5.105-.500.432-3.043 1000* 48.0 1356422 1/4-20 x 5 SD5.105-.500 1.432-4.043 600* 43.5 1356423 1/4-20 x 6 SD5.105-.500 2.432-5.043 500* 34.5 1356424 1/4-20 x 7 SD5.105-.500 3.432-6.043 500* 39.5 1356425 1/4-20 x 8 SD5.105-.500 4.432-7.043 500* 44.5 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 4

Carbon Steel Self-Drill Fasteners with bondseal Washer Metal to metal applications Buy American Act 1 10-16 SD3 12-14 SD3 1/4-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal washer 502820 10-16 x 5/8 SD2.035-.110.087 5000 40.0 793256 10-16 x 3/4 SD3.035-.150.212 5000 45.0 793373 10-16 x 1 SD3.035-.150.462 5000 50.0 793461 10-16 x 1-1/4 SD3.035-.150.712 2500* 27.5 793475 10-16 x 1-1/2 SD3.035-.150.962 2500 30.0 Impax HWH 5/16 AF, with bondseal Washer 1302885 12-14 x 3/4 SD3.035-.210.150 2500 27.5 1303353 12-14 x 1 SD3.035-.210.275 2500 32.5 1303633 12-14 x 1-1/4 SD3.035-.210.525 2500 35.0 1303919 12-14 x 1-1/2 SD3.035-.210.775 2000 32.0 1304186 12-14 x 2 SD3.035-.210 1.275 1500 30.0 796942 12-14 x 2-1/2 SD3.035-.210 1.775 2000 50.0 797019 12-14 x 3 SD3.035-.210 2.275 1500 42.0 797074 12-14 x 4 SD3.035-.210 3.275 1000 34.0 1304321 1/4-14 x 7/8 (lap) SD1.030-.095.235 2500 37.5 Impax HWH 3/8 AF, with bondseal Washer 797143 1/4-14 x 3/4 SD3.050-.210.082 2500 37.5 798515 1/4-14 x 1 SD3.050-.210.332 2000 36.0 798777 1/4-14 x 1-1/4 SD3.050-.210.582 2000 40.0 798957 1/4-14 x 1-1/2 SD3.050-.210.832 2000 44.0 799066 1/4-14 x 2 SD3.050-.210 1.332 1500 40.5 799092 1/4-14 x 2-1/2 SD3.050-.210 1.832 1500 49.5 799104 1/4-14 x 3 SD3.050-.210 2.332 750 28.5 799119 1/4-14 x 4 SD3.050-.210 3.332 1000* 40.6 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 5

Cupped Sealer Self-Drill Fasteners Metal to metal applications Buy American Act 1 12-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax Cupped HWH 5/16 AF, with EPDM Sealing Washer 1303221 12-14 x 3/4 SD3.035-.210.210 2500 27.5 1303490 12-14 x 1 SD3.035-.210.335 2500 32.5 1303719 12-14 x 1-1/4 SD3.035-.210.585 2500 40.0 1303990 12-14 x 1-1/2 SD3.035-.210.835 2000 40.0 1304487 1/4-14 x 7/8 (lap) SD1.030-.095.312 2500 37.5 410 Stainless Steel Self-Drill Fasteners Metal to metal applications Made in USA Painted 12-14 SD3 410 SS No Washer 12-14 SD3 410 SS Aluminum bondseal Washer Silver Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt. 410 Stainless HWH 5/16 AF, No Washer 1360238 12-14 x 3/4 SD3.035-.210.250 5000 40.0 1356328 12-14 x 1 SD3.035-.210.375 2500 25.0 1388437 12-14 x 1-1/4 SD3.035-.210.625 2500 32.5 1299609 1/4-14 x 7/8 (lap) SD1.030-.095.338 2500 32.5 410 Stainless HWH 5/16 AF, with Aluminum bondseal Washer 791261 12-14 x 3/4 SD3.035-.210.150 2500* 25.0 791271 12-14 x 1 SD3.035-.210.275 2500* 30.4 791316 12-14 x 1-1/4 SD3.035-.210.525 2500 37.5 791341 12-14 x 1-1/2 SD3.035-.210.775 2000 34.0 791283 1/4-14 x 7/8 (lap) SD1.030-.095.238 2500 37.5 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 6

ZAC - Zinc Aluminum Capped Self-Drill Fasteners Metal to metal applications Buy American Act 1 12-14 SD3 12-24 SD5 E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. ZAC Impax HWH 5/16 AF, with EPDM washer 794238 12-14 x 1 SD3.035-.210.225 2000 38.0 1304673 12-14 x 1-1/4 SD3.035-.210.475 2000 38.0 1015151 12-14 x 1-1/2 SD3.035-.210.725 1500 31.5 796645 12-14 x 2 SD3.035-.210 1.225 1000 25.0 797195 1/4-14 x 7/8 (lap) SD1.030-.060.202 2000 36.0 798814 1/4-14 x 1-1/4 SD3.035-.210.462 2000 46.0 ZAC Impax HWH 3/8 AF, with EPDM washer 795668 12-24 x 1-1/4 SD4.5.075-.375.312 2000 54.0 795842 12-24 x 1-1/4 SD5.075 -.500.370 1500 40.5 796622 12-24 x 1-1/2 SD5.075-.500.620 1500 34.5 MAC - Stainless Capped Self-Drill Fasteners Metal to metal applications Buy American Act 1 12-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. MAC Impax Stainless Capped HWH 5/16 AF, with EPDM Washer 793796 12-14 x 1 SD3.035-.210.340 2000 24.2 795388 12-14 x 1-1/4 SD3.035-.210.590 2000 28.7 796239 12-14 x 1-1/2 SD3.035-.210.840 1500 22.9 798360 1/4-14 x 7/8 (lap) SD1.030-.095.312 2000 24.9 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 7

Flex5 Selectively Hardened Fasteners with Grade 5 Performance Made in USA Material No. Description Drill Pt. Drill & Tap Capacity Load Bearing Area Carton Qty. Carton Wt.. Flex5 12-14 Self-Drill; HWH 1429720 10-16 x 3/4 SD3.150.380 5000* 40 1429731 12-14 x 7/8 SD3.187.380 4000* 44 1429732 12-14 x 1 SD3.187.500 4000* 44 1429734 12-14 x 1-1/2 SD3.187 1.000 2500* 38 1429736 12-14 x 2 SD3.187 1.500 2000* 16 Flex5 12-14 Self-Drill; PUF (Phillips Undercut Flat) 1429733 12-14 X 1 SD3.187.500 4000* 36 Flex5 12-24 Self-Drill; HWH 1429735 12-24 x 1-3/4 SD5.500.800 2000* 36 Flex5 1/4-14 and 1/4-20 Self-Drill; HWH 1429737 1/4-14 x 1 SD3.187.450 2500* 45 1429738 1/4-14 x 1-1/2 SD3.187.950 2000* 46 1429739 1/4-14 x 2 SD3.187 1.450 1500* 41 1429740 1/4-20 x 1-1/8 SD4.312.500 2000* 40 1429741 1/4-20 x 1-1/2 SD4.312.835 2000* 46 1429742 1/4-20 x 2 SD4.312 1.335 1500* 41 1429743 1/4-20 x 2-1/2 SD4.312 1.830 1000* 19 Flex5 self-drilling fasetners are made from alloy steel and are fi nished with a selective hardness heat treatment process to give the load bearing part of the fastener Grade 5 specifi cations (RC 28-34), with a higher hardness for the drill point and lead-in threads (min. RC 52). Finish: vistacorr TM 12-14 SD3 Flex5 1/4-14 SD3 Flex5 Flex5 Head Marking Grade 5 head and threads (RC 28-34) Ideal for curtainwall, architectural cladding, rainscreen and dissimilar metal applications when used with aluminum. Higher-hardness lead threads and point (min. RC 52) Technical Data Pullout Test Results - Steel Screw Size Point Type Panel Thickness Drill Cap. 18 16 14 12 1/8 3/16 1/4 5/16 10-16 3.150 390 489 628 1575 1685 - - - 12-14 3.187 389 515 704 1672 2048 2895 - - 1/4-14 3.187 391 525 690 1925 2224 3904 3562 4501 1/4-20 4.312-520 643 1903 2542 4225 5408 6612 Pullout Test Results - Aluminum Screw Size Point Type Panel Thickness Drill Cap. 1/8 1/4 3/8 10-16 3.150 893 - - 12-14 3.187 931 2276-1/4-14 3.187 1001 2412-1/4-20 4.312 891 2080 3644 Shear Test Results - Steel Screw Size Point Type Panel Thickness Drill Cap. 18-18 18-14 16-16 14-14 1/8-3/16 3/16-1/4 1/4-12 ga. 10-16 3.150 1351 1720 1448 - - - - 12-14 3.187 1301 2120 1644 1801 - - - 1/4-14 3.187 1391 2322 1664 2401 2549 - - 1/4-20 4.312 1341 2062 1577 2455 2820 2801 2711 Shear Test Results - Aluminum Panel Thickness Screw Size Point Type Drill Cap. 1/8-1/8 18/-14 10-16 3.150 1429-12-14 3.187 1793 2503 1/4-14 3.187 2002 2874 1/4-20 4.312 2006 2913 www.sfsintecusa.com 8

Wood to Metal Self-Drilling Fasteners For attaching wood to steel Buy American Act 1 1/4-20 SD4 Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Ply Metal Self-Drill with Wings; Wafer Head, #2 Phillips Drive 782310 10-24 x 1-7/16 SD2.060-.175 3/4 Plywood 4000 40.0 Header Self-Drill with Wings; Flat Head, #3 Phillips Drive 1380115 12-24 x 2 SD3.060-.210 up to 1 2000 42.0 783132 12-24 x 2-1/2 SD3.060-.210 up to 1-1/2 1500 31.5 Header Self-Drill with Wings; Flat Head, #3 Phillips Drive 1295993 1/4-20 x 2-3/4 SD4.095-.250.090-.250 Steel up to 1-3/4 Wood 1000 33.0 Brown Vista coating for corrosion resistance Suitable for pressure treated wood Exceeds 1,000 hours salt spray testing Wings designed to ream a hole to prevent "wood jacking" Excellent for wood or header attachments to steel Meets ASTM C1513 for cold-formed steel frame connections 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 9

woodgrip TM Fasteners Metal to wood applications 9-15 woodgrip Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HWH 1/4 AF, with controlseal washer 1300564 9-15 x 1 Sharp Pt. 24 ga (.024) 3000 27.0 1300771 9-15 x 1-1/2 Sharp Pt. 24 ga (.024) 2500 27.5 1301007 9-15 x 2 Sharp Pt. 24 ga (.024) 2000 26.0 1301151 9-15 x 2-1/2 Sharp Pt. 24 ga (.024) 1500 24.0 1301264 9-15 x 3 Sharp Pt. 24 ga (.024) 1000 18.0 1302309 12 x 3/4 (lap) Sharp Pt. 2 x 24 ga 3000 27.0 Silver Color woodgrip TM HiLo Wood Screw Metal to wood applications 10-15 woodgrip HiLo Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HiLo, HWH 1/4 AF, with bondseal Washer 1301370 10-15 x 1 Type 17 Pt. 24 ga (.024) 3000 30.0 1301510 10-15 x 1-1/2 Type 17 Pt. 24 ga (.024) 2500 30.0 1301696 10-15 x 2 Type 17 Pt. 24 ga (.024) 2000 22.0 1301884 10-15 x 2-1/2 Type 17 Pt. 24 ga (.024) 1500 25.5 1302003 10-15 x 3 Type 17 Pt. 24 ga (.024) 1000 19.0 1302423 12 x 3/4 (lap) Sharp Pt. 2 x 24 ga 3000 30.0 www.sfsintecusa.com 10

#14 Milled Point Wood Screw Metal to wood applications #14 Type 17-A MP Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. #14 Wood Fastener, HWH 5/16 AF. Type 17-A Milled, with bondseal Washer 1302956 14 x 1 Type 17-A MP.018-.030 2500 37.5 783685 14 x 1-1/2 Type 17-A MP.018-.030 2000 40.4 1303136 14 x 2 Type 17-A MP.018-.030 2000 46.0 1295481 14 x 2-1/2 Type 17-A MP.018-.030 2000 60.0 1295533 14 x 3 Type 17-A MP.018-.030 1500 52.5 evergrip Bi-Metal 300 Series Stainless Fasteners Metal to wood applications 9-15 evergrip Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. evergrip Bi-Metal Stainless HWH 1/4 AF, with Stainless bondseal Washer 790755 9-15 x 1 Sharp Pt. 24 ga (.024) 3000 27.0 790905 9-15 x 1-1/2 Sharp Pt. 24 ga (.024) 2500 27.5 791004 9-15 x 2 Sharp Pt. 24 ga (.024) 2000 26.0 791122 9-15 x 2-1/2 Sharp Pt. 24 ga (.024) 1500 21.0 woodgrip 300 Series Stainless Aluminum Panel Fasteners Aluminum panel applications Painted Colors 9-15 304SS woodgrip Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. 300 Series Stainless Aluminimum Panel woodgrip, 1/4 HWH, Aluminum bondseal Washer 790256 9-15 x 1 Sharp Pt..032 Alum. Max. 3000 24.0 790284 9-15 x 1-1/2 Sharp Pt..032 Alum. Max. 2500 25.0 790339 9-15 x 2 Sharp Pt..032 Alum. Max. 2000 36.0 790360 9-15 x 2-1/2 Sharp Pt..032 Alum. Max. 1500 24.0 790371 9-15 x 3 Sharp Pt..032 Alum. Max 1000 23.0 www.sfsintecusa.com 11

woodmac TM Wood Screw Metal to wood applications 9-15 woodmac E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodmac 1/4 Stainless Capped HWH with EPDM Washer 786866 9-15 x 1 Sharp Pt. 24 ga (.024) 2500 22.5 1201206 9-15 x 1-1/2 Sharp Pt. 24 ga (.024) 2000 20.0 788650 9-15 x 2 Sharp Pt. 24 ga (.024) 1500 21.0 789212 9-15 x 2-1/2 Sharp Pt. 24 ga (.024) 1000 16.0 789518 9-15 x 3 Sharp Pt. 24 ga (.024) 1000 18.0 1201193 12 x 3/4 (lap) Sharp Pt. 2 x 24 ga 2500 25.0 woodzac TM HiLo Zinc Aluminum Capped Fasteners Metal to wood applications 10-15 woodzac HiLo E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodzac HiLo, 5/16 AF Zinc Alloy Capped, with Aluminum bondseal Washer 781449 10-15 x 1 Type 17 Mill Pt. 24 ga (.024) 2500 45.0 1201187 10-15 x 1-1/2 Type 17 Mill Pt. 24 ga (.024) 2000 38.0 781883 10-15 x 2 Type 17 Mill Pt. 24 ga (.024) 1500 31.5 782020 10-15 x 2-1/2 Type 17 Mill Pt. 24 ga (.024) 1000 24.0 782137 10-15 x 3 Type 17 Mill Pt. 24 ga (.024) 1000 27.0 782916 12 x 3/4 (lap) Sharp Pt. 2 x 24 ga 2500 38.9 www.sfsintecusa.com 12

Clip Fasteners Standing Seam Panel Clip #10 Type A Pancake #12-8 XG Pancake #12-8 XG Low Profi le #12 Type A Pancake #10 SD2 Pancake #12 SD 2 Pancake #12-24 SD5 Pancake E-Zinc Plating Material No. Description Drive Type Drill Pt. Carton Qty. Carton Wt.. Metal to Wood Application 1294280 10 x 1 Pancake 2/2 Square Phillips Type A 5000 35.0 1201576 10 x 1-1/2 Pancake 2/2 Square Phillips Type A 2500 23.8 1201768 10 x 2 Pancake 2/2 Square Phillips Type A 2000 20.4 1204879 12-8 x 1 XG Pancake 2/2 Square Phillips Sharp Pt. 4000 28.0 1295005 12-8 x 1-1/2 XG Pancake 2/2 Square Phillips Sharp Pt. 3000 45.0 1295007 12-8 x 2 XG Pancake 2/2 Square Phillips Sharp Pt. 2000 40.0 1270912 12-8 x 1 XG Low Profi le 2/2 Square Phillips Sharp Pt. 4000 28.0 1270916 12-8 x 1-1/2 XG Low Profi le 2/2 Square Phillips Sharp Pt. 3000 45.0 1270920 12-8 x 2 XG Low Profi le 2/2 Square Phillips Sharp Pt. 2000 40.0 782985 12 x 1 Pancake 2/2 Square Phillips Type A 2500 25.0 790272 10 x 1 304 SS Pancake #2 Phillips Type A 2500 20.0 1297583 10 x 2 304 SS Pancake #2 Phillips Type A 2500 20.0 Metal to Metal Appplication 1201230 10-16 x 1 Pancake 2/2 Square Phillips SD2 5000 40.0 1201577 10-16 x 1-1/2 Pancake 2/2 Square Phillips SD2 2500 23.8 1298672 10-16 x 2 Pancake 2/2 Square Phillips SD2 2000 30.0 793826 12-14 x 1 Pancake 2/2 Square Phillips SD2 2500 25.0 796642 12-24 x 1-1/2 Pancake 2/2 Square Phillips SD5 2500 32.6 www.sfsintecusa.com 13

Carbon Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size.021 -.026 1/8 (.125).027 -.050 3/16 (.187).051 -.075 #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A - Carbon Steel; 3/8 HH with bondseal 783137 14 x 3/4 Type A Pre-drill required.500" 2500 32.5 783245 14 x 1 Type A Pre-drill required.750" 2500 40.0 783598 14 x 1-1/4 Type A Pre-drill required 1.000" 2000 36.0 783873 14 x 1-1/2 Type A Pre-drill required 1.250" 2000 40.0 783923 14 x 2 Type A Pre-drill required 1.750" 2000 50.0 784086 14 x 2-1/2 Type A Pre-drill required 2.250" 1500 45.0 784127 14 x 3 Type A Pre-drill required 2.750" 1500 52.5 784146 14 x 3-1/2 Type A Pre-drill required.500-3.250" 1250* 48.5 1049303 14 x 4 Type A Pre-drill required 1.000-3.750" 1000* 42.0 784170 14 x 5 Type A Pre-drill required 2.000-4.570" 750* 36.9 784181 14 x 6 Type A Pre-drill required 3.000-5.750" 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size.021 -.026 1/8 (.125).027 -.050 3/16 (.187).051 -.075 #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A - 304 Stainless Steel; 3/8 HH with Stainless bondseal 790381 14 x 3/4 Type A Pre-drill required.500" 2500 32.5 790397 14 x 1 Type A Pre-drill required.750" 2500 40.0 790433 14 x 1-1/4 Type A Pre-drill required 1.000" 2000 36.0 790446 14 x 1-1/2 Type A Pre-drill required 1.250" 2000 40.0 790471 14 x 2 Type A Pre-drill required 1.750" 2000 50.0 790491 14 x 2-1/2 Type A Pre-drill required 2.250" 1500 45.0 1297713 14 x 3 Type A Pre-drill required 2.750" 1500 52.5 1297719 14 x 3-1/2 Type A Pre-drill required.500-3.250" 1250* 50.0 790533 14 x 4 Type A Pre-drill required 1.000-3.750" 1000* 42.0 790548 14 x 5 Type A Pre-drill required 2.000-4.570" 750* 38.5 790556 14 x 6 Type A Pre-drill required 3.000-5.750" 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. www.sfsintecusa.com 14

Carbon Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size.065 -.085 #8 (.199).085 -.115 #7 (.201).115 -.375 #1 (.228).375 -.500 #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Type Drill Capacity Carton Qty. Carton Wt. Self-Tapping - Type B - Carbon Steel; 3/8 HH with bondseal 784198 1/4-14 x 3/4 Type B Pre-drill required.550" 2500* 35.0 784208 1/4-14 x 1 Type B Pre-drill required.800" 2500* 42.5 784232 1/4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* 44.0 784241 1/4-14 x 2 Type B Pre-drill required 1.800" 2000* 52.0 784248 1/4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* 48.0 784253 1/4-14 x 3 Type B Pre-drill required 2.800" 1500* 54.0 784258 1/4-14 x 3-1/2 Type B Pre-drill required.625-3.300" 1250* 48.75 784262 1/4-14 x 4 Type B Pre-drill required 1.125-3.800" 1000* 47.0 784268 1/4-14 x 5 Type B Pre-drill required 2.125-4.800" 750* 41.25 784273 1/4-14 x 6 Type B Pre-drill required 3.125-5.800" 500* 33.0 Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size.065 -.085 #8 (.199).085 -.115 #7 (.201).115 -.375 #1 (.228).375 -.500 #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Self-Tapping - Type B - 304 Stainless Steel; 3/8 HH with Stainless bondseal 1297746 1/4-14 x 3/4 Type B Pre-drill required.550" 2500* 35.0 1297754 1/4-14 x 1 Type B Pre-drill required.800" 2500* 42.5 1297779 1/4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* 44.0 1297799 1/4-14 x 2 Type B Pre-drill required 1.800" 1500* 40.5 1297811 1/4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* 48.0 1382358 1/4-14 x 3 Type B Pre-drill required 2.800" 750* 28.0 1297829 1/4-14 x 3-1/2 Type B Pre-drill required.625-3.300" 1250* 48.5 1297832 1/4-14 x 4 Type B Pre-drill required 1.125-3.800" 1000* 47.0 999-576 1/4-14 x 5 Type B Pre-drill required 2.125-4.800" 750* 41.5 1297843 1/4-14 x 6 Type B Pre-drill required 3.125-5.800" 500* 33.0 Part number not set up in SAP. Use description to order. Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. www.sfsintecusa.com 15

SX - HWH 304SS Bi-Metal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 SX3 Stainless bondseal SX5 Stainless bondseal SX14 No Washer Painted Colors Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH 1141978 14-11 x 1-1/8.035-.098.354 500 7.7 1133237 14-11 x 1-1/2.035-.098.590 500 8.7 1133239 14-11 x 2.035-.098.787 500 10.2 SX3 Self-Drill No Washer, 5/16 AF HWH 1141971 14-11 x 1-1/8.035-.098.472 1000 10.9 1142006 14-11 x 1-1/2.035-.098.708 1000 13.6 1142057 14-11 x 2.035-.098.905 1000 16.3 SX5 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH 1122767 12-14 x 1-1/4.060-.157.314 500 8.2 1123168 12-14 x 1-1/2.060-.157.472 500 9.0 1134477 12-14 x 1-5/8.060-.157.708 500 9.8 1168765 12-14 x 2-1/2.060-.157 1.496 100 2.4 1133330 12-14 x 3-1/8.060-.157 2.165 250 7.8 1141958 12-14 x 3-3/4.060-.157 2.755 250 8.7 SX5 Self-Drill No Washer, 5/16 AF HWH 1134304 12-14 x 1-1/4.060-.157.432 1000 12.4 1133976 12-14 x 1-1/2.060-.157.590 1000 18.0 1134478 12-14 x 1-5/8.060-.157.826 1000 15.6 1172097 12-14 x 2-1/2.060-.157 1.614 250 5.1 1133309 12-14 x 3-1/8.060-.157 2.283 1000 25.5 1141957 12-14 x 3-3/4.060-.157 2.873 250 7.7 SX14 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH 770785 12-14 x 1-9/16.157-.550.472 500 9.2 773625 12-14 x 1-7/8.157-.550.787 500 10.4 770805 12-14 x 2-1/2.157-.550 1.496 250 6.2 523277 12-14 x 3-1/4.157-.550 2.283 250 7.8 SX14 Self-Drill No Washer, 5/16 AF HWH 770786 12-14 x 1-9/16.157-.550.590 500 7.0 773627 12-14 x 1-7/8.157-.550.905 1000 16.6 770804 12-14 x 2-1/2.157-.550 1.614 250 5.0 526400 12-14 x 3-1/4.157-.550 2.401 500 13.1 SL2 Lap with Stainless bondseal Washer, 5/16 AF HWH 1123164 12-11 x 1 (lap).031-.060.078 250 2.8 1133512 1/4-14 x 1-1/8 (lap).031-.060.078 500 8.0 SL2 Lap No Washer 1133482 12-11 x 1 (lap).031-.060.078 250 2.1 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 16

irius SX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 irius SX3 No Washer irius SX5 Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-L12 irius Self-Drill with Stainless bondseal Washer 1142002 14-11 x 1-1/8.035-.098.354 500 6.5 1196328 14-11 x 1-1/2.035-.098.590 250 3.9 SX3-L12 irius Self-Drill No Washer 1235713 12-11 x 1-1/4.118-.060.590 250 3.1 1142001 14-11 x 1-1/8.035-.098.472 1000 11.1 1142030 14-11 x 1-1/2.035-.098.708 1000 13.8 SX5-L12 irius Self-Drill with Stainless bondseal Washer 1134345 12-14 x 1-1/4.060-.157.314 500 6.6 1134359 12-14 x 1-1/2.060-.157.472 500 7.3 1135437 12-14 x 1-5/8.060-.157.708 500 8.1 1144693 12-14 x 2-1/8.060-.157.787-1.181 250 5.6 1135110 12-14 x 2-7/16.060-.157 1.496 250 6.4 SX5-L12 irius Self-Drill No Washer 1134342 12-14 x 1-1/4.060-.157.432 1000 12.4 1134355 12-14 x 1-1/2.060-.157.590 1000 13.4 1135452 12-14 x 1-5/8.060-.157.826 500 7.8 1241511 12-14 x 2-1/8.060-.157.787-1.181 1000 18.4 1135107 12-14 x 2-7/16.060-.157 1.614 250 5.3 SX14-L12 irius Self-Drill with Stainless bondseal Washer 776328 12-14 x 1-9/16.157-.550.472 500 9.1 SX14-L12 iirius Self-Drill No Washer 776332 12-14 x 1-9/16.157-.550.590 1000 14.1 SL2-L12 irius Self-Drill with 14mm SS bondseal Washer 1135477 1/4-14 x 1 (lap).031-.060.078 500 7.3 SL2-L12 irius Self-Drill with 16mm SS bondseal Washer 1147314 1/4-14 x 1 (lap).031-.060.078 500 8.1 Painted Colors Installation: The E420 irius drive socket (#973316) is required. 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 17

SX - TORX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Rainscreen cladding Facade Panel (HPL, fiber cement) Buy American Act 1 Painted Colors SX5 TORX No Washer SX5 TORX Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-D10 TORX No Washer (T20W) 1193547 10-16 x 1.039-.118.354 500 3.8 SX3-D12 TORX No Washer (T25) 1271253 12-11 x 1-3/16.060-.118.590 250 5.4 1377511 12-11 x 2-1/8.060-.118 1.575 250 4.4 SX5-D12 TORX with Aluminum bondseal Washer (T25) 1133806 12-14 x 1-1/2.060-.157.472 500 6.4 SX5-D12 TORX No Washer (T25) 1133805 12-14 x 1-1/2.060-.157.472 1000 12.0 SL2-S-D12 TORX with Aluminum bondseal Washer (T20W) 1135881 12-11 x 1-1/16 (lap).031-.060.078 250 2.1 SL2-S-D12 TORX No Washer (T20W) 1137560 12-11 x 1-1/16 (lap).031-.060.078 1000 7.5 Blind Rivets Blind rivet attach light gauge Made in USA Call customer service for painted color rivet options Material No. Description US Dimens. Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. All Aluminum Rivet - Dome Head / Rivet Diameter - 1/8 7916756 AA42D Rivet 42.063-.125 #30 (.129-.133) 5000 5.0 791861 AA43D Rivet 43.126-.187 #30 (.129-.133) 5000 5.0 1298352 AA44D Rivet 44.188-.250 #30 (.129-.133) 5000 5.0 All Stainless Rivet - Dome Head / Rivet Diameter - 1/8 792377 STST43D Rivet 43.126-.187 #30 (.129-.133) 5000 15.0 792474 STST44D Rivet 44.188-.250 #30 (.129-.133) 5000 15.0 792523 STST46D Rivet 46.251-.375 #30 (.129-.133) 5000 15.0 1 Buy American Act - Construction Materials Under Trade Agreements www.sfsintecusa.com 18

BULB-TITE Rivets s for up to 1.125 grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Dome Head Protruding Crown - With Washer 1194603 RV6604-5-4W 5/32.067-.250 #20 (.162-.167) 3500* 10.5 1194605 RV6604-5-8W 5/32.250-.500 #20 (.162-.167) 3500* 10.5 1194607 RV6604-6-3W 3/16.050-.187 #4 (.209-.221) 3000* 9.0 1194609 RV6604-6-4W 3/16.062-.250 #4 (.209-.221) 3000* 9.0 1194621 RV6604-6-6W 3/16.187-.375 #4 (.209-.221) 3000* 9.0 1194623 RV6604-6-8W 3/16.312-.500 #4 (.209-.221) 3000* 9.0 1194625 RV6604-6-10W 3/16.437-.625 #4 (.209-.221) 2000* 6.0 1194627 RV6604-6-12W 3/16.563-.750 #4 (.209-.221) 2000* 6.0 1242653 RV6604-6-14W 3/16.687-.875 #4 (.209-.221) 1500* 4.5 1242655 RV6604-6-16W 3/16.812-1.000 #4 (.209-.221) 1500* 4.5 1242657 RV6604-6-18W 3/16.937-1.125 #4 (.209-.221) 1500* 4.5 1194629 RV6604-8-4W 1/4.062-.250 1/4 (.250-.263) 2000* 6.0 1194631 RV6604-8-6W 1/4.125-.375 1/4 (.250-.263) 2000* 6.0 1194633 RV6604-8-8W 1/4.250-.500 1/4 (.250-.263) 2000* 6.0 1194635 RV6604-8-10W 1/4.375-.625 1/4 (.250-.263) 1500* 4.5 1194719 RV6603-9-6W 9/32.032-.375 5/16 (.304-.3125) 1000* 3.0 1194721 RV6603-9-10W 9/32.250-.625 5/16 (.304-.3125) 1000* 3.0 1194723 RV6603-9-12W 9/32.375-.750 5/16 (.304-.3125) 1000* 3.0 Aluminum/Aluminum Dome Head Protruding Crown - No Washer 1194602 RV6604-5-4 5/32.067-.250 #20 (.162-.167) 3500* 24.5 1194604 RV6604-5-8 5/32.250-.500 #20 (.162-.167) 3500* 24.5 1194606 RV6604-6-3 3/16.050-.187 #4 (.209-.221) 3000* 21.0 1194608 RV6604-6-4 3/16.062-.250 #4 (.209-.221) 3000* 21.0 1194620 RV6604-6-6 3/16.187-.375 #4 (.209-.221) 3000* 21.0 1194622 RV6604-6-8 3/16.312-.500 #4 (.209-.221) 3000* 21.0 1194624 RV6604-6-10 3/16.437-.625 #4 (.209-.221) 2000* 14.0 1194626 RV6604-6-12 3/16.563-.750 #4 (.209-.221) 2000* 14.0 1242652 RV6604-6-14 3/16.687-.875 #4 (.209-.221) 1500* 10.5 1242654 RV6604-6-16 3/16.812-1.000 #4 (.209-.221) 1500* 10.5 1242656 RV6604-6-18 3/16.937-1.125 #4 (.209-.221) 1500* 10.5 1194628 RV6604-8-4 1/4.062-.250 1/4 (.250-.263) 2000* 14.0 1194630 RV6604-8-6 1/4.125-.375 1/4 (.250-.263) 2000* 14.0 1194632 RV6604-8-8 1/4.250-.500 1/4 (.250-.263) 2000* 14.0 1194634 RV6604-8-10 1/4.375-.625 1/4 (.250-.263) 1500* 10.5 1194718 RV6603-9-6 9/32.032-.375 5/16 (.304-.3125) 1000* 7.0 1194720 RV6603-9-10 9/32.250-.625 5/16 (.304-.3125) 1000* 7.0 1194722 RV6603-9-12 9/32.375-.750 5/16 (.304-.3125) 1000* 7.0 www.sfsintecusa.com 19

BULB-TITE Rivets, continued s for up to 1.125 grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Large Flange Protruding Crown - With Washer 1194725 RV6605-9-6W 9/32.024-.375 5/16 (.308-.327) 1000* 7.0 1194727 RV6605-9-10W 9/32.250-.625 5/16 (.308-.327) 1000* 7.0 1194730 RV6605-9-12W 9/32.375-.750 5/16 (.308-.327) 1000* 7.0 Aluminum/Aluminum Large Flange Protruding Crown - No Washer 1194724 RV6605-9-6 9/32.024-.375 5/16 (.308-.327) 1000* 7.0 1194726 RV6605-9-10 9/32.250-.625 5/16 (.308-.327) 1000* 7.0 1194728 RV6605-9-12 9/32.375-.750 5/16 (.308-.327) 1000* 7.0 Blind Rivet Tools Installation tools for blind rivets AccuBird 14.4 Volt Cordless Riveting Tool Material Number: 836102 Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah Battery Charger: 110V/60Hz, 60 minute charge time Buy American Act 1 PowerBird (Recommended for BULB-TITE rivets) 14.4 Volt Cordless Riveting Tool Material Number: 835558 Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah Battery Charger: 110V/60Hz, 60 minute charge time Note: 9/32 diameter BULB-TITE will require Nose tip 1195161 and shorter jaws 1195156 required. Batteries: 1222873 14.4 Volt, 1.3 Ah Li-Ion Battery 1222872 14.4 Volt, 2.6 Ah Li-Ion Battery Grommet Fastener Attach fi berglass panels Made in USA Material No. Description Head Style Washer Carton Qty. Carton Wt.. Stainless Grommet / Stainless bondseal 1204129 10-32 x 7/8 5/16 AF Hex 15 mm O.D. 3500* 54.9 1297523 6-32 x 1-1/4 1/4 AF Hex 12 mm O.D. 2500* 25.0 www.sfsintecusa.com 20

Pipe Flashing Square and round base pipe roof pipe flashing Material No. Black EPDM Material No. Gray EPDM Material No. Red Silicone Flasher Size Pipe Diameter Carton Qty. Carton Wt.. Square Base Pipe Flashing 500364 1304853 500367 #1 1/4 to 2-3/4 15 2.7 500391 1304992 500396 #2 7/8 to 4 15 4.8 500401 500406 500412 #3 1/4 to 5-3/4 15 7.65 500417 1305010 500419 #4 2-3/4 to 7 10 7.9 500423 1305019 500424 #5 4 to 8-1/4 10 9.8 500428 1305024 500429 #6 4-3/4 to 10 10 12.2 500433 1305031 500434 #7 5-1/2 to 11 10 15.7 500438 1305034 500439 #8 6-3/4 to 13-1/2 5 12.85 500443 1305040 500444 #9 9-1/2 to 20-1/2 5 25.0 500369 1304856 500370 #10 12 to 28-1/2 5 35.0 Retrofit Square Base Pipe Flashing 500365 500365 500368 #1 1/2 to 4 5 3.5 1204123 500395 500397 #2 4 to 9-1/4 5 3.5 500410 500411 500413 #3 9-1/4 to 16-1/4 5 3.5 Round Base Pipe Flashing 500361 500362 500363 #1 1/4 to 2-1/2 15 2.7 500388 500389 500390 #2 1-3/4 to 3 15 4.8 500398 500399 500400 #3 1/4 to 5 15 7.65 500414 500415 500416 #4 3 to 6-1/4 10 7.9 500420 500421 500422 #5 4-1/2 to 7-3/4 10 9.8 500425 500426 500427 #6 5 to 9 10 12.2 500430 500431 500432 #7 6 to 11 10 15.7 500435 500436 500437 #8 7 to 13 5 12.85 500440 500441 500442 #9 9 to 19 5 25.0 Retrofit Round Base Zipper Pipe Flashing 1304849 1304850 1304855 #1 3/4 to 2-3/4 5 3.5 1304990 1304991 1304994 #2 2 to 7-1/4 5 3.5 1304995 1305006 999-576 #3 3-1/4 to 10 5 3.5 Part number not set up in SAP. Use description to order. Made in USA www.sfsintecusa.com 21

Use for sealing joints and seams in metal panels, gaps around door and window frames, and expansion joints in buildings Pre-compressed, self-expanding polyurethane foam Acrylate dispersion impregnation Resistant to rain, wind, sun/uv, sound, draft and dust Pressure sensitive adhesive for fast and easy installation Flame retardant Hannoband BG1 Joint Sealant Tape Material No. Size Thickness x Width Expanded Thickness @ 100% Performance Fully Expanded Uncompressed Thickness Length/Roll Packaging 1305091 1/4 x 1 1/4 1 x 1 20.0 ft. 12 rolls/ctn 8.0 1305092 3/8 x 1 3/8 1-1/2 x 1 15.0 ft. 12 rolls/ctn 8.0 Ctn. Wt. Application vistacoat Premium System High Performance Color Finish SFS intec developed the vistacoat Premium System fi nish for panel attachment fasteners. Utilizing new coating and processing technology, the fi nish has improved appearance, corrosion resistance, durability and installation performance. The fi nish system consists of: pre-treatment seal coat color top coat - contact SFS intec for color matches zinc plating primer coat Silver vistacoat is standard. Performance Corrosion Resistance - on all plain and color product Kesternich per DIN 50.018 2.0 liter - 15 cycles Salt Spray per ASTM B117 1,000 hrs. Consistent Durability Adhesion Impact resistance Appearance gloss and color; application processes ensure consistent results UV Resistance New superior UV-resistant pigmentation Results exceed previous market offerings in gloss retention and color stability www.sfsintecusa.com 22

#12 Dekfast Phillips Head For insulation attachment For attachment to: Steel roof decks Wood roof decks E-Coat Plating Application / Thickness Material No. Description Steel Wood Concrete Carton Qty. Carton Wt.. #12 Dekfast, #3 Phillips drive, 13 tpi, drill point 785683 12 x 1-5/8" Up to 7/8" Up to 5/8" N/A 1000* 13 785698 12 x 2-1/4" 5/8" to 1-1/2" Up to 1-1/4" N/A 1000* 17 785717 12 x 2-7/8" 5/8" to 2-1/8" Up to 1-1/8" N/A 1000* 21 785735 12 x 3-1/4" 1/2" to 2-1/2" 1/2" to 2-1/4" N/A 1000* 23 785761 12 x 3-3/4" 1" to 3" 1" to 2-3/4" N/A 1000* 26 785781 12 x 4-1/2" 3/4" to 3-3/4" 3/4" to 3-1/2" N/A 1000* 31 785797 12 x 5" 1-1/4" to 4-1/2" 1-1/4" to 4" N/A 1000* 34 785818 12 x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" N/A 1000* 41 785835 12 x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" N/A 500* 24 785851 12 x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" N/A 500* 28 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #12 fasteners meet Factory Mutual corrosion-resistance Standard 4470. Installation Tools: 2000-2500 rpm screw guns with hardened #3 Phillips bit. The standard carton package includes one #3 Phillips bit. www.sfsintecusa.com 23

#14 Dekfast Phillips Head For insulation and membrane attachment For attachment to: Steel roof decks Wood roof decks Structural concrete roof decks E-Coat Plating Material No. Description Application / Thickness Steel Wood Concrete Carton Qty. Carton Wt.. #14 Dekfast, #3 Phillips drive, 10 tpi, drill point 1202602 14 x 1-1/4" Up to 1/2" Up to 1/4" Up to 1/4" 1000* 12 1203249 14 x 2" Up to 1-1/4" Up to 1-1/4" Up to 1" 1000* 19 1203528 14 x 3" Up to 2-1/4" Up to 2" Up to 2" 1000* 24 1203578 14 x 4" 1-1/4" to 3-1/4" 1-1/4" to 3" 2" to 3" 1000* 30 1203605 14 x 5" 1-1/4" to 4-1/4" 1-1/4" to 4" 3" to 4" 1000* 45 1203632 14 x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" 4" to 5" 1000* 46 1203659 14 x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" 5" to 6" 500* 28 1203810 14 x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" 6" to 7" 500* 31 1204081 14 x 9" 5-1/4" to 8-1/4" 5-1/4" to 8" 7" to 8" 500* 34 1202260 14 x 10" 6-1/4" to 9-1/4" 6-1/4" to 9" 8" to 9" 500* 38 1202597 14 x 11" 7-1/4" to 10-1/4" 7-1/4" to 10" 9" to 10" 500* 41 1202600 14 x 12" 8-1/4" to 11-1/4" 8-1/4" to 11" 10" to 11" 500* 45 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board and/or roof cover to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #14 fasteners meet Factory Mutual corrosionresistance Standard 4470. Installation Tools: 2000-2500 rpm screw guns with hardened #3 Phillips bit. For structural concrete, 3/16" carbide bit and 1500 rpm max screw guns, or hammerdrills in the hammer mode. Structural concrete to be pre-drilled to minimum 1/2" deeper than fastener penetration. The standard carton package includes one #3 Phillips bit. Insulation Stress Plates For insulation attachment Use with: #12 Dekfast fasteners #14 Dekfast fasteners Made in USA AZ50 Galvalume Material No. Description Outside Diameter Inside Diameter Carton Qty. Carton Wt.. Insulation Stress Plates 730612 Galvalume Steel Hex Insulation Plate 2-7/8" Hex.270" 1000* 38 739814 Galvalume Steel 3" Round Insulation Plate 3" Round.260" 1000* 41 www.sfsintecusa.com 24

Zinc Nailins For fastening termination bar at wall terminations For attachment to: Concrete Block Brick Stone Material No. Diameter & Length Carton Qty. Carton Wt.. Zinc Nailin, Mushroom Head, Zamac 7 Body 792879 3/16 x 7/8" 500* 5 792880 1/4 x 3/4" 500 8 792881 1/4 x 1" 500* 10 792882 1/4 x 1-1/4" 500* 12 792884 1/4 x 1-1/2" 500* 13 792885 1/4 x 2" 500* 16 * inner boxes of 100 pc./box Performance Load Capacities (4000 psi concrete) Diameter 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" Embed. Depth 3/4" 5/8" 7/8" 1-1/8" 1-3/8" 1-7/8" Tension Load (lbs) 500 600 820 960 1150 1300 Shear Load (lbs) 1000 1500 1500 1500 1500 1500 Notes: Load capacity is related to embedment depth. Select anchor length to provide needed embedment depth for the installed anchor. The 1-1/4" length is popular for 1/8" composite thickness applications resulting in 1-1/8" embedment. All load values listed are ultimate load capacities and are not allowable load capacities. These loads should be reduced by an appropriate safety factor of at least 4 to determine the allowable load. Installation Tools: Carbide-tipped masonry drill bit sized slightly larger than nominal diameter to allow clearance. A 3/16" nominal masonry drill bit is actually.198"-.206" diameter. A 1/4" nominal size is actually.260"-.268" diameter. Procedure: Position the fixture and drill a hole the same diameter as the zinc nailin (3/16" or 1/4"). Insert the anchor and tap gently against the fi xture to be fastened. Drive the nail fl ush to the anchor head to expand the anchor. www.sfsintecusa.com 25

Notes www.sfsintecusa.com 26

epost esolutions - Supply Chain innovations are just a click away eportal eshop Job Pack VMI EDI escan Our Technologies Provide easier, faster & more secure working methods n Reduce supply chain costs n Minimize errors n Improve information availability n epullout eformat Visit our website, or contact us to learn more. www.sfsintecusa.com 1-800-234-4533 Manufacturing Locations Exeter Plant Lincoln Corporate Center, 41 Dennis Drive, Reading, PA 19606 Medina Plant 5201 Portside Drive, Medina, OH 44256 Wyomissing Plant 1045 Spring Street, PO Box 6326, Wyomissing, PA 19610 Canada Plant 40 Innovation Drive, Dundas, ON L9H 7P3 US Service Centers: Contact Us Toll Free: 1-800-234-4533 Toll-free Fax: 888-485-4225 Northeast: 1045 Spring Street, PO Box 6326, Wyomissing, PA 19610 T: 610-376-5751 Northern Midwest: 500 West 3rd Avenue, Durant, IA 52747 T: 563-785-4990 Toll-free Fax: 888-211-4211 Southeast: 675 Progress Center Ave., Unit M, Lawrenceville, GA 30043 West Coast: 2426 Port Street, West Sacramento, CA 95691 F: 563-785-6997 T: 770-995-5256 F: 770-995-3782 T: 916-373-9912 Toll-free Fax: 888-488-8332 F: 916-373-0176 Canada Service Center: Contact Us Toll-Free : 1-866-847-5400 Toll-free Fax: 855-858-5300 40 Innovation Drive, Dundas, ON L9H 7P3 T: 905-689-5041 2016 SFS Intec / Printed in USA Technical advice and sales service SFS intec, Inc. 800 234 4533 Division Construction T +1 610 376 5751 1045 Spring Street F +1 610 376 8551 PO Box 6326 us.construction@sfsintec.biz US-Wyomissing, PA 19610 www.sfsintecusa.com F: 610-376-8551 F: 905-689-9474 Technical Changes Reserved April 2016 SFS intec, Inc. - Canada 40 Innovation Drive Dundas, ON L9H 7P3 T +1 905 689 5401 ca.info@sfsintec.biz www.sfsintec.ca