Moss provides: - Wrench - Gloves - Wash Cloth - 33 Cleaner - Plastic Drop Cloth 2 GENERAL INSTRUCTIONS: - Wipe down all tubing, clean work area and lay out plastic sheeting. - Repack fabric neatly in the bag provided. WORKMANSHIP GUARANTEE: Moss fully guarantees all products against defects in workmanship. If our products receives proper care, but fails due to a defect in manufacturing, the product will be repaired or replaced at our discretion. For damage to products caused by accidents, improper care or negligence, where Moss is not at fault (including sun degradation and wear and tear) repairs will be performed for a reasonable fee. WARNING: Hanging system and structure are designed for: (1) indoor use only and (2) to hold the weight of the structure and fabric cover only. No other loads should be applied to this display system. Connection # Work Order # Component # version 2
PARTS LIST (PER UNIT): QTY REQUIRED: DESCRIPTION: 1 CENTER POST QTY PACKED: BAG/BOX LOCATION:! Do Not Mix Component #'s No "Dumping" Connection # Work Order # 1 TABLE RING 3 TABLE SUPPORT Component # 1 TOP RING 3 CROSS MEMBER 1 HUB 1 BASEPLATE w/ FLANGE 1 TABLETOP 3 FABRIC COVER ALSO INCLUDED: WRENCH GLOVES WASH CLOTH 33 CLEANER PLASTIC DROP CLOTH ZIP-TIES CHARGERS/EXTENSION CORDS (IF PURCHASED) PACKAGED BY:
Before You Start: Lay out plastic sheeting, apply gloves to all hands. Unpack all boxes, remove all framing and components according to line item #. 2 Locate lower fabric cover Place table ring into cover through the unzipped bottom opening and assemble as shown 1! Do Not Mix Component #'s No "Dumping" Slide the center post (2" dia. tube) into flange attached to round plate. Insert a 2" flat head screw up through the plate and into the post. Align the holes in the post with the holes in the flange. Tighten using supplied hex tool. Snap supports to the three (3) connection points BOTTOM FABRIC COVER TABLE RING ASSEMBLE RING INSIDE BOTTOM FABRIC COVER A B TABLE SUPPORT x3 C SNAP-BUTTON SNAP BUTTON T-BUTT T-BUTT NOTE: Alphabetical labels indicate non-corded snap button connections. Align matching labels with one another.
3 Place table ring assembly over the center post and lower down ensuring that center post goes though the center hole of the fabric cover Match connection labels and attach supports to center post using 1 1/4" flat head bolts 4 Place table top over center post and rest on table ring. Locate funnel-shaped fabric, and place small end over center post. Push bottom of fabric through the center holes of the table top and the lower fabric cover. Secure Velcro on fabric to Velcro on center post. Zip cover closed along edge(s) of frame as shown. Zipper location and orientation is shown in Heavy dashed lines. FUNNEL FABRIC TABLE TOP 1 3 2 *FABRIC REMOVED TO SHOW DETAIL Drape fabric loosely until step 11 FULLY ENCLOSED INSTALLATION NOTE: Numerical labels indicate bolted connections. Align matching labels with one another. Fabric tags align with "Place Fabric Tag Here" label on frame.
5 Assemble top ring (36") as shown (use 2" flat head screws for numbered connections) 6 Assemble 48" Rings (2) as shown Bolt cross members to central hub using 1 1/4 " flat head bolts (Bolt up through plate into cross members) TOP RIING CROSS MEMBER x3 48" RING 5 HUB 4 6 x2 SNAP BUTTON FACE-DOWN FOR TOP RING BOLTED SNAP-BUTTON NOTE: Alphabetical labels indicate non-corded snap button connections. Align matching labels with one another. NOTE: Numerical labels indicate bolted connections. Align matching labels with one another. NOTE: Alphabetical labels indicate non-corded snap button connections. Align matching labels with one another.
7 Zip 48" rings into fabric sleeves in top fabric cover 8 Zip the top sleeve of the fabric to the top ring attached to the post as shown. Align zipper breaks with cross members TOP FABRIC COVER SINGLE SKIN INSTALLATION SINGLE SKIN INSTALLATION
9 Securely attach top ring assembly to center post using 1 1/4"" flat head screw through center hole of hub. 1 Lift the top of the funnel fabric and zip it to the inside of the middle ring The Round Charging Station is now complete.