Thanks for shopping with Improvements! 3pc Resin Wicker/Metal Nesting Table Item # 503352ESP NOTE: The product s in this manual are for assembly and operation purposes only. They may differ from the product s actual appearance. To order, call 1-800-642-2112 West Chester, OH 45069 Made in China 1015 If you have questions regarding this product, call 1-800-642-2112 Mon.-Fri. 9:00-5:00 EST (Ohio) and ask for our product specialists or e-mail: productspecialist@improvementscatalog. com See many more products on the Internet! www.improvementscatalog.com Page 1 of 6
Content: Warning and Cautions...2 Care and Maintenance...2 Parts.................................... 3 Assembly...4 Warning and Cautions DANGER: Please keep children out of the assembly area during assembly. WARNING: Do not stand on the tables. CAUTION: Use the tables on flat ground only. IMPORTANT: Please check the tightness of bolts at least every 180 days. Care and Maintenance: Use mild soap and warm water to clean the frames. Rinse with clean water and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove footcaps and tilt frames, if necessary, to remove all water. Water allowed to accumulate inside the frames and then exposed to sub-freezing temperatures can cause damage to frame tubing. Such damage is not coverd under warranty. Any rusts spots should be lightly sanded and treated with rust inhibitor and followed with an application of touch-up paint (not included). Small nicks and scratches can be covered with an application of touch-up paint (not included). Use commercially available glass cleaners. Do not use abrasive materials, cleansers or bleach products. Page 2 of 6
Parts: Hardware Included----Large and Medium size table Notes: Large and medium size table use the same hardware, we have 2 sets of hardware kits inside the carton. The below quantity is for 1 set of hardware that is included. E Bolt (M6*15) 12 F Washer 12 G Bolt Cap 12 H Package Content: Inner Hexagon Wrench 1 A Table Top 2 (1 large and 1 medium) B Left Leg 2 (1 large and 1 medium) C Right Leg 2 (1 large and 1 medium) D Connecting Tube 2 (1 large and 1 medium) Read these instructions carefully before assembling. Wait to dispose of the packing material until assembly is complete and all parts are accounted for. Page 3 of 6
To Assemble: CAUTION: Do not use sharp equipment such as a knife and scissors when removing the protective material, as it may damage the product. Step 1 Step 2 Place the tabe top (A) on a soft & clean level surface. With back side up. Attach the left leg (B) & right leg (C) to the corresonding hole on the table top (A) with steel washer (F), M6*15 bolt (E), bolt cap (G), and inner hexagon wrench (H). Don t over tighten the bolt. Step 3 Attach connecting tube (D) to left leg (B) and right leg (C) as shown below, do not tighten the bolts too much, after all the bolts are connected with left & right leg, finally tighten up all bolts using inner hexagon wrench (H), place the bolt caps (G) on the bolts (E). Step 4 Turn the table over, then it can be used. Note: Large size table and medium size table use the same assembly method or repeat for medium table. Page 4 of 6
Parts: Hardware Included----Small size table D Bolt (M6*15) 16 E Washer 16 F Bolt Cap 16 G Inner Hexagon Wrench 1 Package Content: AA Table Top 1 (small) BB Left Leg 2 (small) CC Connecting Tube 2 (small) Page 5 of 6
To Assemble: CAUTION: Do not use sharp equipment such as a knife and scissors when removing the protective material, as it may damage the product. Step 1 Step 2 Place the tabe top (AA) on a soft & clean level surface. With back side up. Attach the legs(bb) to the corresonding hole on the table top (AA) with steel washer (E), M6*15 bolt (D), bolt cap (F), and inner hexagon wrench (G). Don t over tighten the bolt. Step 3 Attach connecting tube (CC) to legs (BB) as shown below, do not tighten the bolts too much, after all the bolts are connected with left & right leg, finally tighten up all bolts using inner hexagon wrench (H), place the bolt caps (G), place the bolts (F) on the bolts (D). Step 4 Turn the table over, then it can be used. Page 6 of 6