DATASHEET ISL88011, ISL88012, ISL8801, ISL8801, ISL8801 Data Sheet Ld Voltage Supervisors with Adjustable Power-On Reset, Dual Voltage Monitoring or Watchdog Timer Capability FN809 Rev.00 The ISL88011, ISL88012, ISL8801, ISL8801, ISL8801 family of devices offer both fixed and/or adjustable voltage-monitoring that combine popular functions such as Power-On reset control, watchdog timer, supply voltage supervision, and manual reset assertion in a small Ld SOT-2 package. Unique features on the ISL8801 and ISL8801 include a watchdog timer with a 1s start-up timeout and a 1.6s normal timeout duration. On the ISL88011 and ISL8801, users can increase the nominal 200ms Power-On reset timeout delay by adding an external capacitor to the C POR pin. Both fixed and adjustable voltage monitors are provided by the ISL88012. Complementary active-low and active-high reset outputs are available on the ISL88011, ISL88012 and ISL8801 devices. All devices provide manual reset capability (see Product Features Table on page ). Seven preprogrammed reset threshold voltages accurate to ±1.% over temperature are offered (see Ordering Information on page ). The ISL88012, ISL8801 and ISL8801 have a user-adjustable voltage input available for custom monitoring of any voltage down to 0.6V. All parts are specifically designed for low power consumption and high threshold accuracy. Features Single/dual voltage monitoring supervisors Fixed-voltage options allow precise monitoring of +2.V, +.0V, +.V, and +.0V power supplies Dual supervisor has one fixed voltage input and another that is user-adjustable down to 0.6V. Both and outputs available Adjustable POR timeout delay options Watchdog timer with 1.6s normal and 1s start-up timeout durations Manual reset input on all devices Reset signal valid down to = 1V Accurate ±1.% voltage threshold Immune to power-supply transients Ultra low.µa supply current Small Ld SOT-2 Pb-Free package Pb-Free (RoHS Compliant) Applications Process control systems Intelligent instruments Embedded control systems Computer systems Critical µp and µc power monitoring Portable/battery-powered equipment PDA and handheld PC devices FN809 Rev.00 Page 1 of 1
Pinouts ISL88011 ( LD SOT-2) TOP VIEW ISL88012 ( LD SOT-2) TOP VIEW /MR 1 VDD /MR 1 VDD 2 2 CPOR ISL8801 ( LD SOT-2) TOP VIEW ISL8801 ( LD SOT-2) TOP VIEW /MR 1 VDD /MR 1 VDD 2 2 WDI CPOR ISL8801 ( LD SOT-2) TOP VIEW /MR 1 VDD 2 WDI FN809 Rev.00 Page 2 of 1
Ordering Information PART NUMBER PART MARKING V THVDD V TH TEMPERATURE RANGE PACKAGE TAPE AND REEL PKG. (Notes 1, 2, ) (Note ) (V) (V) ( C) (Pb-free) DWG. # ISL88011IH6Z-TK AGU.6 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH6Z-T7A AGU.6 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IHZ-TK AGV.8 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IHZ-T7A AGV.8 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH1Z-TK AGW.09 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH1Z-T7A AGW.09 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH29Z-TK AGX 2.92 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH29Z-T7A AGX 2.92 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH26Z-TK AGY 2.6 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH26Z-T7A AGY 2.6 N/A -0 to +8 Ld SOT-2 P.06 ISL88011IH2Z-TK AGZ 2.2 N/A -0 to +8 Ld SOT-2) P.06 ISL88011IH2Z-T7A AGZ 2.2 N/A -0 to +8 Ld SOT-2) P.06 ISL88011IH22Z-TK (No longer available, recommended replacement: ISL8801IH22Z-TK) ISL88011IH22Z-T7A (No longer available, recommended replacement: ISL8801IH22Z-T7A) AHE 2.19 N/A -0 to +8 Ld SOT-2 P.06 AHE 2.19 N/A -0 to +8 Ld SOT-2 P.06 ISL88012IH6Z-TK (No longer available or supported) AHF.6 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH6Z-T7A (No longer available or supported) AHF.6 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IHZ-TK (No longer available or supported) AHG.8 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IHZ-T7A (No longer available or supported) AHG.8 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH1Z-TK (No longer available or supported) AHH.09 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH1Z-T7A (No longer available or supported) AHH.09 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH29Z-TK (No longer available or supported) AHI 2.92 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH29Z-T7A (No longer available or supported) AHI 2.92 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH26Z-TK (No longer available or supported) AHJ 2.6 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH26Z-T7A (No longer available or supported) AHJ 2.6 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH2Z-TK (No longer available or supported) AHK 2.2 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH2Z-T7A (No longer available or supported) AHK 2.2 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH22Z-TK (No longer available or supported) AHL 2.19 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88012IH22Z-T7A (No longer available or supported) AHL 2.19 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL8801IH6Z-TK (No longer available, recommended replacement: ISL88011IH6Z-TK) ISL8801IH6Z-T7A (No longer available, recommended replacement: ISL88011IH6Z-T7A) AHM.6 N/A -0 to +8 Ld SOT-2 P.06 AHM.6 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-TK AHN.8 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-T7A AHN.8 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH1Z-TK AHO.09 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH1Z-T7A AHO.09 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH29Z-TK AHP 2.92 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH29Z-T7A AHP 2.92 N/A -0 to +8 Ld SOT-2 P.06 FN809 Rev.00 Page of 1
Ordering Information (Continued) PART NUMBER (Notes 1, 2, ) PART MARKING V THVDD (Note ) (V) V TH (V) TEMPERATURE RANGE ( C) PACKAGE TAPE AND REEL PKG. (Pb-free) DWG. # ISL8801IH26Z-TK AHQ 2.6 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH26Z-T7A AHQ 2.6 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH2Z-TK (No longer available, recommended replacement: ISL88011IH2Z-TK) ISL8801IH2Z-T7A (No longer available, recommended replacement: ISL88011IH2Z-T7A) AHR 2.2 N/A -0 to +8 Ld SOT-2 P.06 AHR 2.2 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH22Z-TK AHS 2.19 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IH22Z-T7A AHS 2.19 N/A -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-TK AHT N/A 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-T7A AHT N/A 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-TK (No longer available or supported) AHU N/A 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL8801IHZ-T7A (No longer available or supported) AHU N/A 0.6 (Note 2) -0 to +8 Ld SOT-2 P.06 ISL88011EVAL1Z ISL8801EVAL1Z ISL8801EVAL1Z ISL88011 Evaluation Card ISL8801 Evaluation Card ISL8801 Evaluation Card NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. The voltage trip point can be adjusted to be greater than 0.6V using 2 external resistors. By default, the VTH trip point is 0.6V if no external resistors are used.. For Moisture Sensitivity Level (MSL), please see device information page for ISL88011, ISL88012, ISL8801, ISL8801, ISL8801. For more information on MSL please see techbrief TB6.. The part marking is located on the bottom of the part. Functional Block Diagrams POR /MR POR /MR POR /MR ± V THMON PB ± V THMON PB ± V THMON PB OSC C POR OSC ± V REF WDI WDT ISL88011 ISL88012 ISL8801 R 1 POR /MR R 1 POR /MR R 2 ± V THMON PB R 2 ± VTHMON PB OSC C POR OSC WDI WDT ISL8801 ISL8801 FN809 Rev.00 Page of 1
Product Features Table FUNCTION ISL88011 ISL88012 ISL8801 ISL8801 ISL8801 Active-Low Reset () x x x x x Active-High Reset () x x x Watchdog Timer (WDI) x x Dual Voltage Supervision x Adjustable POR Timeout (C POR ) x x Manual Reset Input (MR) x x x x x Fixed Trip Point Voltage x x x Adjustable Trip Point Voltage x x x Pin Descriptions PIN ISL88011 ISL88012 ISL8801 ISL8801 ISL8801 NAME FUNCTION 1 1 1 1 1 /MR Combined Active-Low Reset Output and Manual Reset Input 2 2 2 2 2 Ground Adjustable Threshold Voltage Input Active-High Reset Output C POR Adjustable POR Timeout Delay Input WDI Watchdog Timer Input Supply Voltage and Monitored Input FN809 Rev.00 Page of 1
R Absolute Maximum Ratings Temperature Under Bias.....................-0 C to +12 C Storage Temperature.......................-6 C to +10 C Voltage on any pin with respect to............ -1.0V to +7V DC Output Current................................... ma ESD Rating Human Body Model (Tested per JESD22-A11).........200V Charged Device Model (Tested per JESD22-C101E).....1200V Machine Model (Tested per JESD22-A11).............20V Thermal Information Thermal Resistance (Typical JA ( C/W) Ld SOT-2 (Note )........................ 190 Maximum Junction Temperature (Plastic Package)....... +12 C Maximum Storage Temperature Range..........-6 C to +10 C Pb-Free Reflow Profile.........................see link below http://www.intersil.com/pbfree/pb-freereflow.asp Recommended Operating Conditions Temperature Range (Industrial).................-0 C to +8 C Pull-up Resistance (R PU )..................... k to CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTE:. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB79 for details. Electrical Specifications Over the recommended operating conditions unless otherwise specified, R PU = 10k. SYMBOL PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Supply Voltage Range 2.0. V I DD Supply Current for ISL88011, =.0V 8 11. µa ISL88012, ISL8801 =.V 7 10 µa = 2.V. 9 µa Supply Current for ISL8801, ISL8801 =.V. 8 µa I LI Input Leakage Current () 100 na I LO Output Leakage Current () 100 na VOLTAGE THRESHOLDS V THVDD Fixed Voltage Trip Point ISL88011, ISL88012, ISL8801IH6.7.6.71 V ISL88011, ISL88012, ISL8801IH.1.8. V ISL88011, ISL88012, ISL8801IH1.0.09.1 V ISL88011, ISL88012, ISL8801IH29 2.88 2.92 2.96 V ISL88011, ISL88012, ISL8801IH26 2.9 2.6 2.67 V ISL88011, ISL88012, ISL8801IH2 2.29 2.2 2. V ISL88011, ISL88012, ISL8801IH22 2.16 2.19 2.22 V V THVDD Hysteresis at Input V THVDD =.6V 6 mv HYST V THVDD =.8V mv V THVDD =.09V 1 mv V THVDD = 2.92V 29 mv V THVDD = 2.6V 26 mv V THVDD = 2.2V 2 mv V THVDD = 2.19V 22 mv V TH Adj. Reset Voltage Trip Point (Note 6) V THVDD =.6V 99 60 611 mv V THVDD =.8V 97 60 609 mv V THVDD =.09V 89 9 601 mv V THVDD = 2.92V 89 9 601 mv V THVDD = 2.6V 89 9 601 mv V THVDD = 2.2V 97 60 609 mv V THVDD = 2.19V 97 60 609 mv FN809 Rev.00 Page 6 of 1
Electrical Specifications Over the recommended operating conditions unless otherwise specified, R PU = 10k. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN TYP MAX UNITS V TH Adj. Reset Voltage Trip Point (Note 7) 9 600 606 mv V TH HYST Hysteresis Voltage (Notes 6, 7) mv RESET V OL Reset Output Voltage Low.V, Sinking 0.mA 0.0 0.0 V <.V, Sinking 0.mA 0.0 0.0 V V OH Reset Output Voltage High.V, Sourcing 0.mA -0.6-0. V <.V, Sourcing 0.mA -0.6-0. V t RPD V TH to Reset Asserted Delay 60 µs t POR POR Timeout Delay ISL88012, ISL8801, ISL8801 10 200 260 ms ISL88011, ISL8801 with C POR = OPEN 200 20 ms C LOAD Load Capacitance on Reset Pins pf MANUAL RESET V MR MR Input Voltage 0 100 mv t MR MR Minimum Pulse Width 1 µs WATCHDOG TIMER (Note 8) Start t WDT Start-up Watchdog Timeout Period 2 1 6 sec t WDT Normal Watchdog Timeout Period 1.0 1.6 2.0 sec t WDPS WDI Minimum Pulse Width 100 ns V IL Watchdog Input Voltage Low 0. x V V IH Watchdog Input Voltage High 0.8 x V I WDT Watchdog Input Current 100 na NOTES: 6. Applies to ISL88012. 7. Applies to ISL8801 and ISL8801. 8. Applies to ISL8801 and ISL8801. FN809 Rev.00 Page 7 of 1
Pin Description The push-pull output is set to (HIGH) listed in the following: 1. The device is first powered up. 2. Either or the voltage on falls below their respective minimum voltage sense levels.. MR is asserted.. The watchdog timeout expires. /MR This pin functions as both a reset output and a manual reset input. The output functions identically to the complementary output but is an open drain output that is pulled to (LOW) when reset is asserted. The MR input is an active-low debounced input to which a user can connect a push-button to add manual reset capability or drive with active low signal from a controller. The pin is the power supply terminal. It is monitored by the ISL88011, ISL88012 and ISL8801. For these devices, the voltage at this pin is compared against an internal factory-programmed voltage trip point, V THVDD. A reset is first asserted when the device is initially powered up to ensure that the power supply has stabilized. Thereafter, reset is again asserted whenever falls below V THVDD. The device is designed with hysteresis to help prevent chattering due to noise. The pin on the ISL88012, ISL8801 and ISL8801 is a monitored input voltage that is user-adjustable. The voltage at this pin is compared against an internal 600mV reference voltage (V TH ) and a reset is asserted whenever the monitored voltage falls below this trip point. WDI The Watchdog Input takes an input from a microprocessor and ensures that it periodically toggles the WDI pin, otherwise the internal watchdog timer runs out and reset is asserted. The internal Watchdog Timer is cleared whenever the WDI input pin sees a rising or falling edge or the device is manually reset. C POR The C POR input pin lets users increase the Power-On Reset timeout delay (t POR ) by connecting a capacitor between C POR and ground. (See Figure ) V THVDD 1V V TH >t MR MR t POR t RPD t POR t RPD t POR t POR FIGURE 1. VOLTAGE MONITORING TIMING DIAGRAM FN809 Rev.00 Page 8 of 1
Principles of Operation The ISL88011, ISL88012, ISL8801, ISL8801, ISL8801 devices provide those functions needed for critical voltage monitoring. These features include Power-On Reset control, customizable supply voltage supervision, Watchdog Timer capability, and manual reset assertion. By integrating all of these features into a small Ld SOT-2 package and using only.µa of supply current, the ISL88011, ISL88012, ISL8801, ISL8801, ISL8801 devices can assist in lowering system cost, reducing board space requirements, and increasing the reliability of a system. Low Voltage Monitoring During normal operation, these supervisors monitor both the voltage level of (ISL88011, ISL88012, ISL8801) and/or (ISL88012, ISL8801, ISL8801). The device asserts a reset if any of these voltages falls below their respective trip points. The reset signal effectively prevents the system from operating during a power failure or brownout condition. This reset signal remains asserted until and the voltage on exceed their voltage threshold setting for the reset time delay period t POR of 200ms (See Figure 1) The ISL88012, ISL8801 and ISL8801 allow users to customize the minimum voltage sense level on the input pin. To do this, connect an external resistor divider network to the pin in order to set the trip point to some voltage above 600mV according to the following Equation 1 (See Figure 2). : R 1 + R 2 V INTRIP = 0.6 ------------------------- (EQ. 1) R 2 Power-On Reset (POR) Applying at least 1V to the pin activates a POR circuit which asserts reset (i.e., goes HIGH while goes LOW). The reset signals remain asserted until the voltage at and/or rise above the minimum voltage sense level for time period t POR. This ensures that the voltages have stabilized. These reset signals provide several benefits: It prevents the system microprocessor from starting to operate with insufficient voltage. It prevents the processor from operating prior to stabilization of the oscillator. It ensures that the monitored device is held out of operation until internal registers are properly loaded. It allows time for an FPGA to download its configuration prior to initialization of the circuit. Adjusting POR Timeout via C POR Pin On the ISL88011 and ISL8801, users can adjust the Power-On Reset timeout delay (t POR ) up to many times the normal t POR of 20ms. To do this, connect a capacitor between C POR and ground (see Figure ). For example, connecting a 0pF capacitor to C POR will increase t POR from a typical 20ms to about 2.s. NOTE: Care should be taken in PCB layout and capacitor placement in order to reduce stray capacitance as much as possible, which lengthens the t POR timeout period. C POR ISL88011 ISL8801 V IN R 1 R 2 ISL88012 ISL8801 ISL8801 6 FIGURE 2. USING TO MONITOR V IN VIA RESISTORS t POR (s) 2 1 0 0 10 20 0 0 0 60 70 80 C POR (pf) FIGURE. ADJUSTING t POR WITH A CAPACITOR FN809 Rev.00 Page 9 of 1
Manual Reset The manual reset input (MR) allows the user to trigger a reset by using a push-button switch. The MR input is an active-low debounced input. By connecting a push-button directly from MR to ground, the designer adds manual system reset capability (see Figure ). Reset is asserted if the MR pin is pulled low to less than 100mV for 1µs or longer while the pushbutton is closed. After MR is released, the reset outputs remain asserted for t POR (200ms) and then released. ISL88011 ISL88012 ISL8801 ISL8801 ISL8801 R pu /MR PB Watchdog Timer The Watchdog Timer circuit checks microprocessor activity by monitoring the WDI input pin. The microprocessor must periodically toggle the WDI pin within t WDT (1.6s nominal), otherwise the reset signal is asserted (see Figure ). Internally, the 1.6s timer is cleared by either a reset or by toggling the WDI input. Besides the 1.6s default timeout during normal operation, these devices also have a longer 1s timeout for start-up. During this time, a reset cannot be asserted due to the WDI not being toggled. The longer delay at power-on allows an operating system to boot, an FPGA to initialize, or the system software to initialize without the burden of dealing with the Watchdog. Symbol Table WAVEFORM INPUTS OUTPUTS FIGURE. CONNECTING A MANUAL RESET PUSH-BUTTON Must be steady May change from LOW to HIGH May change from HIGH to LOW Don t Care: Changes Allowed N/A Will be steady Will change from LOW to HIGH Will change from HIGH to LOW Changing: State Not Known Center Line is High Impedance V THVDD 1V START t WDT <t WDT <t WDT STARTt WDT WDI t WDT >t WDPS t POR t POR FIGURE. WATCHDOG TIMING DIAGRAM FN809 Rev.00 Page 10 of 1
Typical Parametric Performance Curves 11.70 I DD (µa) 10 9 8 7 6 VDD = V VDD =.V VDD = 2.V - - -2-1 0 1 2 6 7 8 9 V THVDD (V).6 V THVDD =.6V.60..0..0. V THVDD =.8V.0 - - -2-1 0 1 2 6 7 8 9 TEMPERATURE ( C) TEMPERATURE ( C) FIGURE 6. I DD (ISL88011, ISL88012, ISL8801) vs TEMPERATURE FIGURE 7. V THVDD, = V vs TEMPERATURE V THVDD (V).20.10.00 2.90 2.80 2.70 2.60 2.0 V THVDD =.09V V THVDD = 2.92V V THVDD =.8V 2.0 - - -2-1 0 1 2 6 7 8 9 TEMPERATURE ( C) FIGURE 8. V THVDD, =.V vs TEMPERATURE FIGURE V THVDD (V) 2.0 2. 2.0 V THVDD = 2.2V 2.2 2.20 V THVDD = 2.19V 2.1 2.10 - - -2-1 0 1 2 6 7 8 9 TEMPERATURE ( C) 9. V THVDD, = 2.V vs TEMPERATURE 0.608 0.606 20 22 V TH (V) 0.60 0.602 0.600 t POR (ms) 220 21 210 0.98 20 0.96 - - -2-1 0 1 2 6 7 8 9 TEMPERATURE ( C) FIGURE 10. V TH vs TEMPERATURE 200 - - -2-1 0 1 2 6 7 8 9 TEMPERATURE ( C) FIGURE 11. t POR (C POR OPEN) vs TEMPERATURE FN809 Rev.00 Page 11 of 1
Typical Application Circuits 12V 12V 10k 12V SUPPLY 180k 10k.7V RESET k 0.1µF 10k PGOOD @ 10.8V PGOOD @ 10.8V ISL8801 / ISL8801 V TH @ 11.V ISL88011IH1Z FIGURE 12. HIGH ACCURACY 12V SUPPLY MONITOR FIGURE 1. 12V SUPPLY PGOOD or PGOOD 12V V +V PGOOD 180k V TH @ 11.V V TH2 @.V V2MON -V 10k 6.81k ISL88012 -V ISL88012IH6Z FIGURE 1. MONITOR V AND 12V SUPPLIES PGOOD = HIGH IF -V < -.6V AND -V + +V > 9. (abs) FIGURE 1. +V AND -V MONITOR.V.V V THL @.09V PGOOD 0k ISL8801X-1.V V THH @.6V 10K ISL8801/ISL8801 VOLTAGE OUT OF RANGE = P GOOD LOW FIGURE 16. OVER/UNDERVOLTAGE MONITOR FN809 Rev.00 Page 12 of 1
ISL8801XEVAL1Z Board Schematics FIGURE 17. ISL88011EVAL1Z FIGURE 18. ISL88012EVAL1Z FIGURE 19. ISL8801EVAL1Z FIGURE 20. ISL8801EVAL1Z Each of the ISL8801X parts has its own evaluation board provided with minimal customization, allowing the user to program with passive components both the POR timing and adjustable thresholds, where applicable. The ISL88011EVAL1Z, ISL88012EVAL1Z and ISL8801EVAL1Z have a.6v Vth part installed. FIGURE 21. ISL8801EVAL1Z FIGURE 22. THE TYPICAL ISL8801XEVAL1Z MEASURING 0. x 1 FN809 Rev.00 Page 1 of 1
Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE FN809. Updated Ordering Information Table on page and page. Added Revision History and About Intersil sections. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support Copyright Intersil Americas LLC 200-201. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN809 Rev.00 Page 1 of 1
Package Outline Drawing P.06 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev, /11.00 2.80 (1.90) 8 0 0.22 0.08.00 2.60 1.70 1.0 0.20 (0.008) M C 2 0.0 0.0 (0.9) TOP VIEW SEE DETAIL X END VIEW 0.2 0.10 0.10 MIN 0.10 (0.00) C 0.1 0.00 1.0 0.90 1. 0.90 SEATING PLANE C SEATING PLANE C 0. 0. (0.60) 8 0 GAUGE PLANE (0.2) SIDE VIEW DETAIL "X" x (0.60) x (1.2) (2.) NOTES: 1. Dimensioning and tolerance per ASME Y1.M-199. 2. Package conforms to EIAJ SC-7 and JEDEC MO178AA.. Package length and width are exclusive of mold flash, protrusions, or gate burrs.. Footlength measured at reference to gauge plane. (2x 0.9). Lead thickness applies to the flat section of the lead between 0.08mm and 0.1mm from the lead tip. 6. Controlling dimension: MILLIMETER. Dimensions in ( ) for reference only. (1.90) TYPICAL RECOMMENDED LAND PATTERN FN809 Rev.00 Page 1 of 1