Puerto Rico - ressing Table ssembly Instructions - Please keep for future reference 615/6350 615/8578 imensions of the dresser Width - 17cm epth - 48cm Height - 84cm imensions of the bench Width - 40cm epth - 40cm Height - 4.5cm Important Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the ustomer Helpline: 08456 400 800 Issue 1-1/04/11
Safety and are dvice Important Please read these instructions fully before starting assembly heck you have all the components and tools listed on pages and 3. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. o not stand or put weight on the product, this could cause damage. ssemble the item as close to its final position (in the same room) as possible. ssemble on a soft level surface to avoid damaging the unit or your floor. This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault. The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture. On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time. This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Parts of the assembly will be easier with people. ispose of all packaging carefully and responsibly. are and maintenance Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product. void placing the furniture in direct sunlight as this will cause the timber to prematurely age. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. 1 Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
omponents - Panels Please check you have all the panels listed below 9 rawer bottom x (41.8 x 8.6cm) 1 Top panel (17 x 48cm) 10 Side drawer runner x (3.8 x 6.5cm) eg x 4 (81 x 6.cm) 11 Middle drawer runner (3.8 x 8cm) 3 Front frame (107. x 1cm) view from behind 1 Seat panel (40 x 40cm) 4 Back panel (107. x 1cm) 5 Side panel x (8. x 1cm) 6 rawer front x (43. x 11.cm) eg frame x (40 x 36cm) 7 rawer side x 4 (30 x 11.cm) 8 rawer back x (40.8 x 11.cm) ross rail x (8.6 x 6.5cm)
omponents - Fittings If you have damaged or missing components, call the ustomer Helpline: 08456 400 800 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. B Wooden dowel x 4 16mm Screw x 16 30mm Screw x 16 E F 35mm Screw x 18 19mm Bolt x 60mm Bolt x 8 G H 100mm Bolt x 4 Half moon nut x 4 Metal bracket x 8 K M rawer handle x Round Metal stud x 1 llen Key x 1 Tools required Phillips screwdriver m Ruler/tape measure Small hammer Eye protection (when using a hammer or glue) Ruler - Use this ruler to help correctly identify the screws 0 5 10 15 0 5 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 10 15 0 5 0 5 150 155 160 165 170 3
ssembly Instructions Step 1 Insert dowels indicated parts. into the x x 5 10 11 Step Fixing Metal brackets. B ttach metal brackets to the front frame 3 and back panel 4 using screws B in the pre drilled holes. 3 4 Step 3 Fixing drawer runners. Place drawer runners and 11 in the position shown ensuring dowels and front frame 3 and back panel 4 are all fit into their holes at the same time. 10 Fix drawer runners 10 and 11 to the front frame and back panel 4 using screws. 3 3 10 4 11 10 4
ssembly Instructions Step 4 Fixing side panels. ttach metal brackets to the side panels 5 using screws in the pre drilled holes. B B 5 5 5 Step 5 Fixing legs. ttach metal brackets into the pre drilled holes in the legs using bolts F with the allen key M as shown. F M 5
ssembly Instructions Step 6 Fixing top. Two people are required for an easier assembly. aution: arefully lay the top panel 1 on a soft and clean surface to avoid damaging the product. ttach cabinet to the top panel 1 using screws. Important: With help, after fixing top panel, carefully stand the product upright. 1 Step 7 rawer assembly. a: ttach drawer sides 7 to the drawer front 6 using screws. b: Slide drawer bottom into slots on drawer sides and position drawer back 8 in place. a: b: 7 7 6 9 8 c: Holding the drawer back 8, press the drawer sides and fix them using screws. c: d: d: Using bolts E attach the drawer handle K to the drawer front. E Repeat step 7 for the other drawer. K 6
ssembly Instructions Step 8 a: Fix round metal studs into the pre drilled a: holes in legs. NO! NO! YES! b: b: Insert drawers into unit. With the back of the drawers past the front frames, use a hammer to tap dowels in flush to drawer sides. This is a safety catch to stop drawer falling out. Step 9 ssembling bench. Fit cross rails leg frame. to the M G Insert half moon nut H into cross rails. Fix cross rails to leg frame using bolts G and allen key M as shown. H 7
ssembly Instructions Step 10 Fit leg frame rails. to cross Insert half moon nut H into cross rails. Fix cross rails to leg frame using bolts G and allen key M as shown. H G M Step 11 a: Insert 4 dowels into leg frame. a: b: aution: arefully lay the seat panel 1 on a soft and clean surface to avoid damaging the product. b: ttach bench to the seat panel 1 using screws. 1 ssembly is complete. If you need help or have damaged or missing parts, call the ustomer Helpline: 08456 400 800 8