Edixeon RGB Series Datasheet Edixeon Series Features : Three chips (colors) in one package Independent control of each color More energy efficient than incandescent and most halogen lamps Low voltage operation Instant light Long operating life IR reflow process compatible Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 1
Table of Contents General Information...3 Absolute Maximum Ratings...4 Characteristics...4 Luminous Flux Characteristic...5 Mechanical Dimensions...6 Characteristic Curve...8 Reflow Profile...11 Reliability...12 Product Packaging Information...13 Revision History...14 About Edison Opto...14 Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 2
General Information Introduction Edixeon RGB emitters are one of the highest flux LEDs in the world by Edison Opto. It is designed to satisfy applications of Solid-State lighting. It is designed to have three chips in one package. It has various colors for choice and can be independently controlled. More importantly, it can pass reflow process. Ordering Code Format 2 E x1 03 M1 00 000 xxx X1 X2 X3 X4 X5 X6 X7 X8 X1 X2 X3 X4 X5 Type Component Series Wattage Color 2 Emitter E Edixeon A1 A1 Series 03 3W M1 RTB R1 R1 Series X6 X7 X8 Internal code PCB Board Serial Number - - 000 - - - Ordering Code Format (Emitter on Star ) 5 E A1 03 M1 S 001 xxxx X1 X2 X3 X4 X5 X6 X7 X8 X1 X2 X3 X4 X5 Type Component Series Wattage Color 5 Module E Edixeon A1 A1 Series 03 3W M1 RTB X6 X7 X8 Internal code Quantity Serial Number S Star 001 1 pcs - - Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 3
Absolute Maximum Ratings Parameter Symbol Value Units DC Forward Current I F 350 ma Peak Pulsed Current; (tp 100μs, Duty cycle=0.25) I pulse 700 ma LED Junction Temperature T J 120 C Operating Temperature - -30 ~ +110 C Storage Temperature - -40 ~ +120 C ESD Sensitivity (HBM) - 2,000 V Soldering Temperature - 260 C Manual soldering time at 260 o C (Max) - 5 Sec. Notes: 1. Proper current derating must be observed to maintain junction temperature below the maximum at all time. 2. LEDs are not designed to be driven in reverse bias. 3. Allowable reflow cycles are 3 times for each LED. 4. tp : Pulse width time Characteristics Parameter Symbol Value Units Viewing Angle (Typ.) 2Θ 1/2 115 Degree Forward voltage (350mA) (700mA) V F R : 2.2 T /B : 3.4 R : 2.6 T /B : 3.8 Thermal resistance - R : 16 T : 13 B : 11 V F / T V F / T -2 mv/ C Wavelength JEDEC Moisture Sensitivity - Notes: 1. Wavelengths are stated as peak wavelength. 2. Edison maintains a tolerance of ±1nm for dominant wavelength, ±2nm for peak wavelength and ±5% on CCT measurement. 3. Edison maintains a tolerance of 0.06V on forward voltage measurement. λd 620-630 515-535 450-475 Level 2a Floor Life Conditions: 30 C / 60% RH Soak Requirements(Standard) Time (hours): 120+1/-0 Conditions: 60 C / 60% RH V o C/W nm - Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 4
Luminous Flux Characteristic Luminous Flux Characteristics at I F =350mA, T J =25 C Color Group Min. Luminous Flux(lm) Max. Luminous Flux(lm) Red R0 39.4 51.2 True Green T0 66.5 86.5 M0 13.8 17.9 N0 17.9 23.3 Red Q0 30.3 39.4 True Green T0 66.5 86.6 M0 13.8 17.9 N0 17.9 23.3 Red Q0 30.3 39.4 True Green T0 66.5 86.6 N0 17.9 23.3 P0 23.3 30.3 Red Q0 30.3 39.4 True Green T0 66.5 86.6 N0 17.9 23.3 P0 23.3 30.3 Order Code 2ER103M100000002 (non star) 5EA103M1S0010001 (on star) 2ER103M100000001 2EA103M100000004 2EA103M100000005 (non star) 5EA103M1S0010002 (on star) Notes: 1. Flux is measured with an accuracy of ± 10%. 2. All true green and blue emitters are built with InGaN. 3. All red emitters are built with AlGaInP. Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 5
Mechanical Dimensions Emitter Type Dimension 2ER103M100000001 Circuit 6.50 5.69 1.05 Lens 2.70 Housing g Lead Lead 2ER103M100000002&2EA103M100000005 Circuit Lens Housing g Lead Notes: 1. All dimensions are in mm. 2. Lambertian and side emitting series slug has polarity as anode. 3. It is important that the slug can t contact aluminum surface. It is strongly recommended that there should coat a uniform electrically isolated heat dissipation film on the aluminum surface. Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 6
2EA103M100000004 Circuit Lens Lead Housing Notes: 1. All dimensions are in mm. 2. Lambertian and side emitting series slug has polarity as anode. 3. It is important that the slug can t contact aluminum surface. It is strongly recommended that there should coat an uniform electrically isolated heat dissipation film on the aluminum surface. LED Package with Star Dimensions and Polarity 5EA103M1S0010001 5EA103M1S0010002 Edixeon Pad Star Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 7
Characteristic Curve Spectrum Normalized Luminous Flux 1.0 0.8 0.6 0.4 0.2 0.0 400 420 440 460 480 500 520 540 560 580 600 620 640 660 680 70 Wavelength(nm) Color Spectrum for White series at T J =25 C Radiation Diagram Normalized Relative Intensity Intensity(%) 100 80 60 40 20 True Green Red Measure Direction 0-100 -80- -60-40- -20 002 2004 406 608 801 100 Angular (Degree) 100 Normalized Relative Intensity(%) 80 60 40 20 True Green Red Measure Direction 0-100 -80- -60-40- -20 002 2004 4006 608 8001 100 Angular (Degree) Lambertain angle at T J =25 C for Edixeon RGB series Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 8
Normalized Relative Radiometric(%) 100 80 60 40 20 Red True Green Measure Direction 0-100 -80- -60-40- -20 02 20 04 06 40 08 60 0180 00100 Angular (Degree) Lambertain angle at T J =25 C for Edixeon RGB series (2EA103M100000004) Luminous Flux & Forward Current Normalized Luminous Flux Forward Current (ma) Forward current & relative luminous at T J =25 o C for Edixeon RGB series Wavelength & Forward Current 550 540 Wavelength(nm) Wavelength(nm) 530 520 510 500 490 480 470 True Green Wavelength(nm) 460 450 50 150 250 350 450 550 Forward Current(mA) Forward Current (ma) Wavelength & forward current for True Green and color Edixeon RGB series Forward Current (ma) Wavelength & forward current for Red color Edixeon RGB series Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 9
Relative Intensity & Junction Temperature Normalized Intensity Junction Temperature( o C) Junction temperature & power rate for Edixeon RGB series Junction Temperature( o C) Wavelength characteristic for Edixeon RGB Red chip Wavelength(nm) Wavelength(nm) Wavelength(nm) Junction Temperature( o C) Wavelength characteristic for Edixeon RGB True Green chip Junction Temperature( o C) Wavelength characteristic for Edixeon RGB chip Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 10
Reflow Profile The following reflow profile is from IPC/JEDEC J-STD-020D which provided here for reference. Classification Reflow Profiles Profile Feature Preheat/Soak Temperature Min (T smin ) Temperature Max (T smax ) Time (ts) from (T smin to T smax ) Ramp-up rate (TL to T P ) Liquidous temperature (TL) Time (tl) maintained above TL Peak package body temperature (T P ) (1) Classification temperature (T C ) Time (tp) within 5 C of the specified classification temperature (Tc) (2) Average ramp-down rate (T p to T smax ) Time 25 C to peak temperature Low-Temp,Pb-Free Assembl 150 C 200 C 60-120 seconds 3 C/ seconds max. 217 C 60-150 seconds 255 C~260 C 260 C 30 seconds 6 C/second max. 6minutes max Notes: 1. Tolerance for peak profile temperature (Tp) is defined as a supplier minimum and a user maximum. 2. Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 11
Reliability NO. Test Item Test Condition Remark 1 Temperature Cycle 2 Thermal Shock -40 C~100 C 30, 30, mins -40 C~100 C 15, 15 mins 10 sec 100 Cycle 100 Cycle 3 Resistance to Soldering Heat T SOL =260 C, 30 sec 3 times 4 Moisture Resistance 25 C~65 C 90% RH 24 hrs / 1 cycle 10 Cycle 5 High-Temperature Storage T A =100 C 1,000 hrs 6 Humidity Heat Storage T A =85 C RH=85% 1,000 hrs 7 Low-Temperature Storage T A =-40 C 1,000 hrs 8 Operation Life test 25 C 1,000 hrs 9 High Temperature Operation Life test 85 C 1,000 hrs 10 High Humidity Heat Life Test 85 o C, 85%RH 1,000 hrs 11 ON/OFF Test 30 sec ON, 30 sec OFF 10W times Failure Criteria Item Criteria for Judgment Min. Max. Lumen Maintenance 85% - Δu'v' - 0.006 Forward Voltage - Initial Data x 1.1 Reverse Current - 10 μa Resistance to Soldering Heat No dead lamps or visual damage Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 12
Pa rt N o: E DE W- KL C8 -B 3 Group : UZ 1V 03 Co lor: Whit e Qu anti ty: 100 0 艾笛森光電股份有限公司 ED ISON OPTO CO PORA TION In spec ted by : A4 100000 05 Di rec tive C omplia nce Te l +86-2- 8227 6996 Fa x +8 6-2- 82 27-6 997 4F N o. 800 Chun g- Chen g., C hun g- Ho C ity Taip ei. Taiw an Product Packaging Information Tape and Reel Dimension Cover Tape Carrier Tape Leader Length 20 Pockets Edixeon Emitter Humidity Indicator 17" Reel Seal Label Moisture absorbent material Label Moisture proof bag 1000pcs LEDs inside RO HS 2 bags in 1 box 5 boxes in 1 carton Note : 445*410*415 (Tolerance : ±5mm) Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 13
Revision History Versions Description Release Date 1 Establish order code information 2012/12/05 2 Update the Luminous Flux Characteristic 2013/01/30 3 Add Reflow & Reliability 2014/05/26 4 Add On star Information 2015/06/12 About Edison Opto Edison Opto is a leading manufacturer of high power LED and a solution provider experienced in LDMS. LDMS is an integrated program derived from the four essential technologies in LED lighting applications- Thermal Management, Electrical Scheme, Mechanical Refinement, Optical Optimization, to provide customer with various LED components and modules. More Information about the company and our products can be found at Copyright 2015 Edison Opto. All rights reserved. No part of publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photo copy, recording or any other information storage and retrieval system, without prior permission in writing from the publisher. The information in this publication are subject to change without notice. For general assistance please contact: service@edison-opto.com.tw For technical assistance please contact: LED.Detective@edison-opto.com.tw Copyright 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 4 14